LAZER FORD Transit Custom Bumper Beam Install for Triple-R 1250 Instruction Manual

June 3, 2024
LAZER

LAZER FORD Transit Custom Bumper Beam Install for Triple-R 1250 Instruction Manual

TECHNICAL SUPPORT

aaron@lazerlamps.com / sales@lazerlamps.com
+44 (0)1992 945601 / +44 (0)1992 677374

WHAT’S REQUIRED

  • FORD TRANSIT CUSTOM 2018+ MOUNTING KIT
  • TRIPLE-R 1250 STANDARD, SMARTVIEW or ELITE WITH I-LBA
  • ONE-LAMP HARNESS KIT (INCLUDED WITH SMARTVIEW & ELITE I-LBA)
  • DASHBOARD CONTROLLER (REQUIRED FOR SMARTVIEW ONLY)
  • CANM8 CANDUO (REQUIRED FOR SMARTVIEW ONLY)

DIFFICULTY LEVEL

DIFFICULTY LEVEL

TOOLS REQUIRED

TOOLS REQUIRED
TOOLS REQUIRED

PRE-INSTALLATION CHECKS

  1. Ensure battery is disconnected.

BUMPER REMOVAL

STEP 1
Remove the x2 T30 screws on each headlight.
BUMPER REMOVAL

STEP 2
Unplug the headlights on both sides.
BUMPER REMOVAL

STEP 3
Lift out both headlights.
BUMPER REMOVAL

STEP 4
Remove x12 plastic push rivets.
BUMPER REMOVAL

STEP 5
Remove number plate.
BUMPER REMOVAL

STEP 6
Remove the x2 13mm bolts behind number plate.
BUMPER REMOVAL

STEP 7
Remove x4 T30 screws from under bumper.
BUMPER REMOVAL

STEP 8
Remove the x2 T25 screws on the inside of both wheel arches.
BUMPER REMOVAL

STEP 9
Unplug bumper loom connector located behind washer resovoir.
BUMPER REMOVAL

STEP 10
Gently pull both corners of the bumper out.
BUMPER REMOVAL

STEP 11
Unclip retaining clip on both sides under headlight.
BUMPER REMOVAL

STEP 12
Pull top centre of bumper up and unclip the retaining clips on both sides of the vehicle.
BUMPER REMOVAL
BUMPER REMOVAL

MOUNTING YOUR TRIPLE-R 1250

STEP 1
Remove part of the radiator support bar as shown as you will need this space for the light to fit in place.
MOUNTING

STEP 2
Fix each Centre Mount to the Bumper Beam brackets as shown using the supplied: bolt, 3x nuts, spring and penny washer (centrally on the middle mounting slot).
MOUNTING
MOUNTING

STEP 3
The rotating feature will need to be removed and turned round so that the M5 grub screws are showing at the front of the mount instead of behind.
MOUNTING
MOUNTING

STEP 4
Mark where you will mount the Bumper Beam Brackets to the bumper beam as per the measurements shown.
MOUNTING

STEP 5
Drill the 5mm pilot holes for the rivets for the Bumper Beam Brackets (2 rivets per bumper beam bracket).
MOUNTING

STEP 6
Using a rivet gun, rivet the Bumper Beam Brackets into place.
MOUNTING

STEP 7
The Triple-R 1250 Smartivew can now slide onto the Centre Mounts, once in place, tighten the M5 grub screws on the Centre Mounts.
MOUNTING

STEP 8
Assemble Stay bar and place in lamp channel to mark where you will bend the Stay Bar in order to mount it to a secure surface.
MOUNTING
MOUNTING

STEP 9
Bend the Stay Bar where you have marked and secure to the vehicle using a self tapping screw and to the lamp using the M5 grub screws included in the kit.

Be sure to avoid the Red highlighted area as this is where a Air-Bag sensor is located.
MOUNTING

STEP 10
Prepare the grille ready to be re-fitted to the vehcle.
Cut the main grille underneath the ford badge as per the measurements shown.
MOUNTING

STEP 10.1
MOUNTING

WIRING

Please refer to Lamp instructions when connecting a Triple-R 1250 Elite with I-LBA.
Steps 4 onwards is for Triple-R 1250 Smartview only.

STEP 1
Live (red wire) should be taken from the 10mm stud next to engine fusebox.
WIRING

STEP 2
Ground should be taken from 10mm bolt in front of the engine fusebox.
WIRING

STEP 3
Switch can be fed through the cab through the bulkhead, alternatively the light can be connected directly to the highbeam (Grey wire at the back of the headlight)
Cable entry for the vehicle is located on the far right of the bulkhead.
You will need to feed the live and earth cable as well as the lamp cables through here.
WIRING

STEP 4
Remove the right hand cupholder.
WIRING

STEP 5
Undo the x2 T25 torx screws below the cup holder.
WIRING

STEP 6
Remove the lower cover and unscrew the T25 torx behind.
WIRING
WIRING

STEP 7
Remove the panel beneath the steering wheel.
WIRING

STEP 8
Pull the trim forward and unplug the light switch, then completely remove panel. Remove light switch and plug back in to stop noise.
WIRING

STEP 9
Unscrew the 3x T25 screws holding in the right hand panel and remove to reveal the interior fusebox.
WIRING

STEP 10
Live, earth and Smartview lamp wires can be brought through to fusebox area.
WIRING

STEP 11
Ignition feed for ATU can be taken from the yellow/grey wire in the black plug by the door.
WIRING

STEP 12
Plug in the ATU as per wiring diagram incuded with Triple-R Smartview Quick- start guide.

Run the cable for the Dashboard Controller (recommended location shown).
WIRING

STEP 13
Red wire in the black plug by the door is 12V live for CanM8 T30 bolt below can be used as ground/earth for CanM8.
WIRING

STEP 14
Locate the OBD plug on the right hand side, undo the 2x 8mm nuts to get access for the canbus wiring to install the CanM8.
WIRING

CAN-M8 DUO INTERFACE INFOMATION

INTERFACE

RED > 12V LIVE RED WIRE
BLACK > GROUND/EARTH T30 BOLT
WHITE > OBD PIN 3 (GREY/ORANGE)
BLUE > OBD PIN 11 (PURPLE/ORANGE)

INSTALLATION CHECKS

  1. Ensure battery is re-connected properly.
  2. Test light bar is working fully before re-assemblying vehicle.

Logo
Thank you for choosing a Lazer Lamps product.

Lazer Lamps Ltd | Units 1-2 Harlow Mill Business Centre | Riverway | Harlow | CM20 2FD | UK | +44 (0) 1992 677374 | www.lazerlamps.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals