LAZER VW Caddy 2021+ Bumper Beam Mounting Kit Instruction Manual

June 3, 2024
LAZER

LAZER VW Caddy 2021+ Bumper Beam Mounting Kit

LAZER-VW-Caddy-2021+ Bumper-Beam-Mounting-Kit-PRODUCT.

TECHNICAL SUPPORT

aaron@lazerlamps.com / sales@lazerlamps.com
TELL: +44 (0)1992 945601 / +44 (0)1992 677374

WHAT’S REQUIRED

  • 1x Linear-18
  • 1x Single Lamp Harness Kit
  • 1x Bumper Beam Clamp Mounting Kit (Part no.)
  • Optional: 1x Lazer CAN interface (if your vehicle has LED headlights and you are unable to find a 12V signal from the highbeam headlight trigger.

DIFFICULTY LEVEL

TOOLS REQUIRED

LAZER-VW-Caddy-2021+-Bumper-Beam-Mounting-Kit-FIG-1

  • METRIC SOCKET SET
  • WIRE STRIPPERS AND RACHET CRIMPERS
  • WIRE CUTTERS
  • T-25 TORX SCREWDRIVER
  • PLASTIC TRIM TOOLS

PRE-INSTALLATION CHECKS

Ensure battery is disconnected

BUMPER REMOVAL

STEP 1: Push the clip leaver on the bonnet release forward.
STEP 2: Pull the bonnet release catch up and remove.
STEP 3: Remove the x4 Torx 25 screws securing the top of the grille.
STEP 4: Remove the x9 Torx 25 screws under the bumper.
STEP 5: Remove the 3 Torx 25 screws from both sides of the inner wheel arch lining.
STEP 6: Gently pull the edge of the bumper out on both sides.
STEP 7: On the Left Hand side of the vehicle, unplug the electrical plugs attached to the bumper.
STEP 8: The bumper can now be removed and set safely to one side.

FITTING YOUR LAMP

STEP 1: Remove the Polystyrene insert from the crash bar.
STEP 2: Brackets will need to be assembled with the side brackets as shown.LAZER-VW-Caddy-2021+-Bumper-Beam-Mounting-Kit-
FIG-11
STEP 3: Install the brackets at either side including the Linear side mounting brackets, around the crash bar.
STEP 4: Install Linear 18 lamp onto the brackets and make any necessary adjustments to the side and bumper beam brackets to ensure lamp is sitting central.
STEP 5: Cut the 4 inner vertical veins off of the bumper and Remove any excess material to give a flush fitting, this can be done via sanding, filing or rotary tool.
Take care not to damage the paint on the bumper. LAZER-VW-Caddy-2021
+-Bumper-Beam-Mounting-Kit-FIG-15
STEP 6: Connect the Lazer wiring harness as shown below:
STEP 7: Reposition bumper and make any required adjustments to lamp height and depth.
Test the light function before reinstalling bumper screws.

WIRING INFORMATION

For instructions on wiring a Linear-18 Elite with Intelligent Low-beam, please refer to the instruction leaflet in the lamps box.

IMPORTANT INFORMATION
When you start any VW MY06+ after having the battery disconnected the dashboard will display multipule errors. To reset the errors please follow steps below:

  1. TURN ENGINE ON
  2. TURN WHEELS FULL LOCK TO LEFT
  3. TURN WHEELS FULL LOCK TO RIGHT
  4. SWITCH IGNITION OFF
  5. RESTART VEHICLE AND ERRORS WILL DISAPPEAR

WWW.LAZERLAMPS.COM
+44 (0)1992 677374
sales@lazerlamps.com
ADDRESS: Lazer Lamps Ltd, Units 1&2 Harlow Mill Business Centre, Riverway, Harlow, Essex. CM20 2FD. United Kingdom

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals