LAZER VOLVO V60 Bumper Beam Mounting Kit Instruction Manual

June 9, 2024
LAZER

LAZER VOLVO V60 Bumper Beam Mounting Kit Instruction Manual
LAZER VOLVO V60 Bumper Beam Mounting Kit

WHAT’S INCLUDED

  • Side Bracket Kit (1118K-B)
  • M6 Fasteners

ALSO REQUIRED

  • 1x Linear-18 (Standard, Elite or Elite with i-LBA)
  • 1x One-Lamp Harness

DIFFICULTY LEVEL

DIFFICULTY LEVEL

TOOLS REQUIRED

TOOLS REQUIRED

PRE-INSTALLATION CHECKS

Ensure battery is disconnected.

STEP 1
Installation Instruction

Locate and remove the x6 silver torx 25 screws from under the front bumper
Installation Instruction

STEP 2
Installation Instruction

Remove the x2 plastic push rivets holding the front ‘under bonnet’ plastic cover in place.
Installation Instruction

STEP 3

Remove the front ‘under bonnet’ plastic cover to reveal the x5 torx 25 screws on the top of the bumper.
Installation Instruction

STEP 4

Undo the x5 torx 25 screws on the top of the bumper.
Installation Instruction

STEP 5

Undo the x6 torx 25 screws inside the front wheel arch.

Peel back the liner to access the bolts securing the front bumper.

Repeat for both sides.
Installation Instruction

STEP 6

Undo the x2 8mm bolts holding the bumper into place.

Repeat for both sides.
Installation Instruction

STEP 7

The bumper can now be removed and placed on a protective surface.
Installation Instruction

STEP 8

The bumper can now be removed and placed on a protective surface.
Installation Instruction

STEP 9

Remove the adhesive rubber strip that is on the lower aluminum impact bar
Installation Instruction

STEP 10

Mark out 400mm from each edge of the lower aluminum impact bar.
Installation Instruction

STEP 11

Drill a 6.5mm hole all the way through the impact bar where you have marked out.

Installation Instruction

STEP 12

Mount the Linear side brackets to the included bigger side brackets (1118K-B).

Then mount the bigger side brackets (1118K-B) to the Linear-18 as shown

STEP 13

Fix the lamp to the reverse of the impact bar as shown using the included 40mm M6 bolt and fasteners.
Installation Instruction

STEP 14

Ensure the Linear-18 is working correctly before re-assembling the vehicle.

(Wiring Instructions on the next page)
Installation Instruction

WIRING INFORMATION

LAZER WIRING KIT

Mount the relay and connect the live and earth connections.

Tidy-up all wiring using cable ties.
WIRING INFORMATION 

WIRING WITH SWITCH

Run the switch cable through the factory grommet.

Drill a 20mm hole and install theswitch.
WIRING INFORMATION 

WIRING WITH SPLICE

The purple high beam trigger can be fed through the bulkhead grommet, located under the inspection panel as shown.

Please test the wires for a 12V signal beforehand
WIRING INFORMATION 

CAN INFORMATION

All vehicles with factory LED headlights will require a Canbus Interface.

The CAN wiring is located at the CEM (Body Control Module), in the Black/Green wiring connector, behind the dash pocket at the lower driver’s side dash aera
CAN INFORMATION 

CAN HI – GREY / BROWN
CAN LO – YELLOW / PURPLE
CAN INFORMATION 

TECHNICAL SUPPORT

Email: sales@lazerlamps.com
Phone: +44 (0)1992 677374

Lazer Lamps Ltd, Units 1&2 Harlow Mill Business Centre,
Riverway, Harlow, Essex. CM20 2FD. United Kingdom

MADE IN THE UK
Facebook icon /LAZERLAMPS
Instagram icon /LAZERLAMPS

Lazer logoWWW.LAZERLAMPS.COM

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals