Clarke DH20L 20 Litre Dehumidifier (R290) User Manual

20 LITRE DEHUMIDIFIER (R290)
MODEL NO: DH20L
PART NO: 6470683

OPERATION & MAINTENANCE **INSTRUCTIONS**

INTRODUCTION

Thank you for purchasing this CLARKE 20 Litre Dehumidifier.
Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.
This guarantee does not affect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

| Recycle unwanted materials instead of disposing of them as waste. All unwanted accessories and packaging should be sorted and taken to a recycling center for disposal in a manner that is compatible with the environment.
By purchasing this product, the customer is taking on the obligation to deal with its safe disposal in accordance with the Waste Electrical and Electronic Equipment regulations (WEEE).
---|---

In effect, this means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognized disposal facility.
R290 is a refrigerant that complies with EEC environmental standards; nonetheless, the refrigerant circuit on the machine should not be punctured. At the end of its working life, consign the dehumidifier unit to a special collection center.

ELECTRICAL CONNECTIONS

**| WARNING!** READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY.
---|---

Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage.
This product may be fitted with a non-rewireable plug. If it is necessary to change the fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or due to damage, it should be cut off and a replacement fitted, following the wiring instructions shown below. The old plug must be disposed of safely, as insertion, we would emphasize the electrical hazard.

**| WARNING:** WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN/YELLOW = EARTH, BLUE = NEUTRAL, BROWN = LIVE.
---|---

• The BLUE wire must be connected to the terminal marked N or colored black.
• The BROWN wire must be connected to the terminal marked L or colored red.
• The YELLOW AND The GREEN wire must be connected to the terminal marked Eor or colored green.
  

We strongly recommend that this machine is connected to the main supply via a Residual Current Device (RCD).
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

OVERVIEW

SAFETY WARNINGS

WARNING: IF THE SUPPLY CABLE IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER, ITS SERVICE AGENT, OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD.

1. Please read these instructions carefully and retain them for future reference.
2. Position the mains cable so that it cannot be inadvertently pulled or pinched and where it does not cause a trip hazard.
3. This appliance is designed to dehumidify residential environments and MUST NOT be used for other purposes.
4. If the appliance requires repair, always contact your CLARKE dealer. ALWAYS insist on original spare parts. Repairs carried out by unauthorized persons may be dangerous and invalidate the guarantee.
5. Children SHOULD NOT play with the appliance. Cleaning and user maintenance SHOULD NOT be undertaken by children.
6. Before cleaning or maintenance operations, ALWAYS unplug the appliance from the power supply.
7. DO NOT move the appliance by pulling the power cable.
8. DO NOT install the appliance in rooms containing gas, oil, or fuel. DO NOT install near sources of heat.
9. DO NOT use the appliance on inclined surfaces.
10. Keep the appliance at least 50 cm away from inflammable substances (alcohol etc) or pressurized containers (e.g. aerosol cans).
11. DO NOT rest heavy or hot objects on top of the appliance.
12. ALWAYS transport the appliance upright. Remember to drain the tank before moving the appliance. Wait at least 1 hour after transporting the appliance before using it to allow the refrigerant gasses to settle.
13. DO NOT use the appliance outdoors.
14. DO NOT obstruct the air inlet or outlet.

R290 REFRIGERANT GAS (HYDROCARBON PROPANE)

H220: Extremely Flammable Gas.

H280: Contains Gas Under Pressure, May Explode if Heated.

R290 refrigerant gas complies with European environmental directives.
R290 has a low GWP (Global Warming Potential) of 3.
The dehumidifier contains approximately 52g of R290 refrigerant gas. The refrigerant system MUST NOT be perforated or punctured.

• DO NOT use or store in an unventilated space with an area smaller than 4m2 per unit. The room must be such as to prevent stagnation of possible leaks of refrigerant gas as there could be a danger of fire or explosion hazard should the refrigerant come into contact with electric heaters, stoves, or other sources of ignition.
• Refrigerant gas may be odorless.
• DO NOT use the product and contact the retailer for advice if damage has occurred to the unit which may have compromised the refrigerant
• Any repairs or maintenance must only be carried out on the unit by a suitably qualified engineer. Before opening and servicing the unit, the authorized engineer must be in possession of a copy of the manufacturer’s service manual and must follow the safety information contained within it to ensure all hazards are minimized.

SAFETY SYMBOLS

| Read the manual and safety instructions before use| | Do not cover when in use
---|---|---|---
| Indoor use only| |

SET UP & POSITIONING THE DEHUMIDIFIER

WARNING: DO NOT USE OR STORE THE DEHUMIDIFIER NEAR A HEAT SOURCE, AS THE UNIT CONTAINS PRESSURISED FLAMMABLE REFRIGERANT GAS (R290-HYDROCARBON PROPANE)

• Empty any water that is in the water tank before every use.
• During the running of the dehumidifier, refrain from opening doors or windows as much as possible.
• Position the dehumidifier close to a mains electrical supply socket.
• The appliance should be installed, operated and stored in a room with a floor area larger than 4m2
• Free space as indicated must be left around the dehumidifier, so as not to block the airflow.
• Make sure that the power cable is not placed where it can be inadvertently pulled or pinched and where it does not cause a trip hazard.

OPERATION

CONTROL PANEL

1. = TIMER (24HR SETUP)
   Press this button to set the length of time the dehumidifier runs for (1-24 Hours) via the LCD display. To cancel the timer, press the button twice once the timer is set.

2. = DRYING
   Press this button to start the dehumidifier drying procedure. This will prevent mold inside the dehumidifier due to dampness. The whole drying procedure takes approximately 1 hour. Press the button again to cancel the drying procedure.

3. = AIRSPEED
   Use this button to adjust the fan speed (High or Low).

4. = LCD DISPLAY – DISPLAYS HUMIDITY, TIME & ERRORS
   This displays the room humidity. When set in AUTO mode, this will display the set humidity in the percentage of humidity.

5. = HUMIDITY SETTING
   Press this button to display and change the humidity range (30% – 80%). The humidity setting is only valid in AUTO mode.

6. = MODE
   During start-up or timer start-up, press this button to select AUTO, CONTINUOUS, or DRYING modes. The indicator light will correspond with the mode selected. Long press (3 seconds) the button to select Child lock mode, and repeat the procedure to cancel/turn off the child lock mode.

7. = ON/OFF
   Press this button to turn the dehumidifier on or off.

SELECT MODE

SETTING OF TIMER – OFF

• When the dehumidifier is running, press the TIMER button to adjust the time from 1 hour to 24 hours, pressing once for each If the time exceeds 24 hours, the count will reset to 1 hour and will start the cycle again.
• At the start of the set time, the dehumidifier will turn itself off

SETTING OF TIMER – ON

• When the dehumidifier is in standby mode, press the TIMER button to adjust the time from 1 hour to 24 hours, pressing once for each hour. If the time exceeds 24 hours, the count will reset to 1 hour and will start the cycle again.
• At the end of the set time, the dehumidifier will turn itself on

AUTO MODE

• Press the MODE button and select AUTO, if the room humidity is higher than the set humidity or is between +5% or -5% of the set humidity the compressor will start and the fan will run at the set speed. If the room humidity is lower than the set humidity by -5% then the compressor will stop but the fan will run at the set speed.

NOTE: The default set humidity value is 50%.

CONTINUOUS MODE

• Press the MODE button and select CONTINUOUSly. No matter how high the relative humidity in the room is, the compressor will start, the fan will run at high speed and the air speed can be regulated via the AIRSPEED

DEHUMIDIFIER DRYING MODE

NOTE: The whole procedure takes approximately 1 hour.

HOW TO START

• Press the DRYING button to start drying within the dehumidifier.
• The dehumidifier will start at high air speed and release air continuously for 30
• The dehumidifier will reduce to low airspeed and run for 20 minutes.

HOW TO STOP

• Press the DRYING button again to cancel the drying procedure, which will return the dehumidifier to the running state before the start of the drying procedure.
• Or press the ON/OFF button to stop the drying procedure, which will return the dehumidifier to the standby state.

CHILD LOCK

• Press and hold the MODE button for 3 seconds. This will enable the child lock function. This will disable all the operational buttons on the Control
• To unlock the child lock function, press and hold the MODE button for 3

DRYING CLOTHES

Used to dry a carpet or small space or to dry wet clothes faster.

• Position the dehumidifier with the air inlet facing wet clothes/carpet, leaving enough space as indicated on page 6.

AIR CLEAN

Used to filter the air.

• The filter must be fitted for the air cleaning function to work.

EMPTYING THE WATER TANK

1. When the full indicator on the panel illuminates (FL) and the buzzer sounds 10 times, switch off and disconnect from the mains supply.
2. Carefully remove the water tank by placing your fingers in the depressions on either side of the tank and pulling outwards.
3. Lift the handle and remove the cover.
4. Discard the water.
5. Before refitting the water tank, check to confirm the indicator float moves freely.
6. Replace the cover and refit the water

NOTE: The unit will not operate unless the water tank is fitted correctly.

|
---|---

CONTINUOUS DRAINING
This function enables continuous dehumidifying without having to empty the water tank.

PREPARATION FOR CONTINUOUS DRAINING:

1. Locate the water drain cap on the rear of the machine and unscrew it.
2. Fit the drainage pipe supplied onto the water drain outlet.
3. Always replace the drain cap when not using the continuous draining procedure.

NOTE: The pipe should have an internal diameter of 9mm and an outer diameter of 12mm.
NOTE: Make sure that the drain pipe always runs downhill away from the dehumidifier and the end should be a minimum of 10cm below the water drain outlet.
NOTE: DO NOT submerge the end of the pipe in water, as this may cause water to be drawn back up into the machine.

MAINTENANCE

WARNING: ALWAYS UNPLUG THE DEHUMIDIFIER BEFORE PERFORMING ANY CLEANING OR MAINTENANCE OPERATIONS.

CLEANING THE CABINET

• Use a soft damp cloth to clean the exterior.
• Never use harsh chemicals or abrasive cleaning agents as these may damage the casing finish.
• Clean the water tank and its cover regularly to prevent mold build-up.

CLEANING THE AIR FILTER

|
---|---

1. Pull the filter cover forwards, from the bottom.
2. Remove the filter cover and lift the filter out.
3. Wash the filter under running water to remove any dust and
4. Allow the fitter to dry naturally.
5. Refitting is the reverse process.

The frequency depends on the duration and the level of dust in the environment. If the machine is being used regularly, it is recommended that you clean the filter every 2 weeks.

STORAGE

• Unplug from the main socket and empty the tank.
• Clean and reinstall the fitter.
• Cover the dehumidifier to prevent dust from getting into the workings.

TROUBLESHOOTING

| Cause| Solution
---|---|---
No operation| Plug fuse failure.| Check the fuse in the plug and replace it if necessary.
The water tank is full or placed incorrectly.| Check water tank and empty if necessary and/or check water tank positioning.
The ambient temperature is lower than 5°C or higher than 32°C.| This machine will not operate outside of these boundaries.
Dehumidifier function not effective| Room temperature too high, humidity too low.| In dry conditions, the dehumidification ability will reduce.
Air filter blocked.| Remove filter and clean, see page 12. Remove any dirt or obstruction from the air intake.
Noise is abnormal during

operation

| A dehumidifier is positioned improperly.| Check that dehumidifier is placed on a flat level surface.
Air filter blocked.| Remove filter and clean, see page12.
There is a ‘tittering’ sound.| This is the flow of the refrigerant, which is a normal

phenomenon.

Water Leak| The connection of the drainage pipe becomes loose.| Check pipe connection.
The drainage system is blocked.| Remove the obstacle and straighten out the drainage pipe.
Frosting Occurs| The ambient temperature is low and the machine is waiting to defrost,| This is a normal phenomenon and the dehumidifier has an automatic defrost function.

DISPLAY CODES

9
El| Coil Sensor Detects Anomaly, Contact Your CLARKE Dealer for Assistance.| Contact Your CLARKE Dealer for Assistance.
E2| Room Temperature Sensor Detects Anomaly, Contact Your CLARKE Dealer for Assistance.| Contact Your CLARKE Dealer for Assistance.
P1| Unit is in Defrosting State (Normal)| Normal No Action Needed.
CL| Unit is in Internal Drying State (Normal).| Normal No Action Needed.
LC| Child Lock Function is Active.| See Page 10

TECHNICAL SPECIFICATION

DECLARATION OF CONFORMITY

A SELECTION FROM THE VAST RANGE OF

QUALITY PRODUCTS

|

AIR COMPRESSORS
From DIY to industrial, Plus air tools,
spray guns and accessories.

GENERATORS
Prime duty or emergency standby
for business, home and leisure.

POWER WASHERS
Hot and cold, electric and engine
driven – we have what you need

WELDERS
Mig, Arc, Tig, and Spot.
From DIY to auto/industrial.

METALWORKING
Drills, grinders, and saws for DIY
and professional use.

WOODWORKING
Saws, sanders, lathes, mortisers
and dust extraction.

HYDRAULICS
Cranes, body repair kits,
transmission jacks for all types of
workshop use.

WATER PUMPS
Submersible, electric, and engine-driven
for DIY, agriculture, and industry.

POWER TOOLS
Angle grinders, cordless drill sets,
saws and sanders.

STARTERS/CHARGERS
All sizes for car and commercial use.

|
---|---|---

PARTS & SERVICE:
0208 988 7400
Pans Enquiries
Parts@clarkeinternational.com
Servicing & Technical Enquiries
Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
Clarke® INTERNATIONAL Hemnall Street, Epping, Essex CM16 4LG
www.clarkeinternational.com

Documents / Resources

| Clarke DH20L 20 Litre Dehumidifier (R290) [pdf] User Manual
DH20L, 20 Litre Dehumidifier R290
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>