Flexispot F8LD Desk Mount Dual Monitor Mount Installation Guide
- June 4, 2024
- FLEXISPOT
Table of Contents
Flexispot F8LD Desk Mount Dual Monitor Mount
Package Included
- Arm x 1 PC
- monitor plate x 2 PCS
- Bottom support 1 x 1 PC
- Anti-slip rubber 1 x 4 PCS
- Anti-slip rubber 2 x 4 PCS
- Cable cover x 1 PC
- Bottom support 2 x 1 PC
- Bolt x 1 PC
- Anti-slip rubber 3 x 1 PC
- Washer x 1 PC
- Butterfly knob x 1 PC
- 6x6mm Hex key x 1 PC
Attachment Screw Set
Tools Needed for Assembly
Installation Steps
STEP 1: Preparations before installing monitor
- Verify that the monitor has holes at VESA spacings, either 100 x 100mm or 75 x 75mm. If it does not have this pattern, the monitor cannot be installed.
- Remove the monitor’s original fixed base. Be careful not to scratch the screen.
STEP 2 – Option A: Install bracket to the desk
This option is for desks without a grommet hole.
- Attach the bottom support 1 (3) to the arm (1) by tightening screws (C) with 4 x 4mm hex key (E).
- Turn the mount upside-down and put anti-slip rubber 2 (5) onto the bottom support 1 (3).
- Put anti-slip rubber 1 (4) onto the top of knob.
- Please select the appropriate mounting holes according to the thickness of desk.
- Position the bottom clamp against desk surface and fully tighten clamp knob.
STEP 2 – Option B: Install bracket using bolt through hole in the desk
This option is for desks with a grommet hole.
- Insert the bolt (8) into the hole of the bottom support 2 (7) to the base by tightening screws (C) with 4 x 4mm hex key (E).
- Turn the mount upside-down and put anti-slip rubber 2 (5) onto the bottom support 2 (7).
- Insert the bottom support into the desk hole.
- Attach anti-slip rubber 3 (9) onto the washer (10).
- Screw in the washer with the butterfly knob.
STEP 3 – Option A: Attach panel monitor to monitor plate
- Add washers (D) to appropriate screws (A or B) – depending on monitor hole size.
- Attach the monitor to monitor plate (2), and tightening screws (A or B) with 5 x 5mm hex key (F).
Note: Attach all four screws through monitor plate and tighten securely.
STEP 4:Attach monitor to the arm
Attach monitor to the connecting plate and confirm locking.
STEP 5: Adjust arm to balance your monitor
After the adjustment, if the monitor appears to droop or sag, please use hex key (F) to fasten the bolt.
. STEP 6: Using cable management system
PRODUCT SPECIFICATION
CAUTION
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children.
- Make sure these instructions are read and completely understood before attempting installation. If you are unsure of any part of this installation, please contact a professional installer for assistance.
- The desk or mounting surface must be capable of supporting the combined weight of the mount and the monitor, otherwise, the structure must be reinforced.
- Proper tools must be used. A minimum of two people are required for this installation. Failure to install properly can result in property damage.
- Check joint parts every two months, making sure the screws have not loosened.
This product was designed to be installed on a desk. Before installing, make sure the mount will support the combined load of the equipment and hardware. Never exceed the maximum load capacity 22 lbs (10 kg), or else it may result in product failure.
Note:
This product is intended for indoor use only. Use of this product outdoors
could lead to product failure.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>