Embassy PoolCo 5-2091-013 Standard Thru Wall Skimmer User Guide

Embassy PoolCo 5-2091-013 Standard Thru Wall Skimmer

Product Specifications

• Product Name: Standard Thru-Wall Skimmer
• Model Number: 5-2091-013
• Brand: Embassy PoolCo
• Designed for: Pool maintenance

Product Usage Instructions

Pool Preparation
The pool must be properly erected per your Pool Assembly & Installation Instructions. Ensure there is approximately 2 feet of water up the metal wall so the liner is under weight and stretched to the proper position before installing the skimmer. Note that the liner cannot be shifted after the skimmer entry holes have been cut.

Skimmer Installation

1. Remove all components from the carton including lid, basket, and hardware package.
2. Attach the standard weir assembly to the skimmer using three screws, ensuring the foam side is down.
3. Trim the liner around the skimmer wall cutouts and vacuum port cutout using a razor knife and a piece of plywood as a guide.
4. Pierce additional holes through the liner using the faceplate as a guide and insert and tighten screws through the faceplate, gaskets, liner, pool wall, and skimmer.

Routine Care & Maintenance
To keep your pool sparkling clean, follow these steps:

1. Provide a clean walkway leading to your pool entrance.
2. Rinse off the patio and area around the pool regularly.
3. Bathers should rinse off, especially their feet, before entering the pool.

Return Fitting Installation

1. Use a board to hold the liner against the return fitting cutout from inside the pool and cut away the liner from outside using a razor knife.
2. Install the return fitting u-gasket into the wall opening, ensuring the liner’s edge is trapped under the gasket. Insert the threaded end of the return fitting adaptor through the wall from inside the pool.

Frequently Asked Questions (FAQ)

• Q: How often should I clean the skimmer basket?
  A: It is recommended to clean the skimmer basket regularly to help your pool stay sparkling clean and sanitary.

• Q: What is the purpose of the vacuum port cover?
  A: The vacuum port cover is required to assure a tight seal around the vacuum adaptor when vacuuming.

Standard
Thru-Wall Skimmer
Models 5-2091-013

Your new Embassy PoolCo Thru-Wall Skimmer makes pool maintenance easier and more convenient. Leaves, insects and floating debris are pulled from the pool into the skimmer basket. Clean the basket regularly to help your pool stay sparkling clean and sanitary. The numbers in parentheses (00) refer to key numbers in the illustration on page 5.

Tools You Will Need

• Large Nail (Approx.. 2″ Long)
• Flat Head Screwdriver
• Phillips Screwdriver
• Razor Knife

POOL PREPARATION
The pool must be properly erected per your Pool Assembly & Installation Instructions. There should be approximately 2′ of water up the metal wall so the liner is under weight and stretched to proper position prior to installing skimmer. NOTE: The liner cannot be shifted after the skimmer entry holes have been cut.

SKIMMER INSTALLATION

1. Remove all components from carton. Remove lid from skimmer by sliding forward and lifting. Remove basket and hardware package from skimmer.
2. Attach standard weir assembly (7) to skimmer (3) using three screws (8). Push the weir inside the skimmer so that the foam side is down.
3. Firmly press a piece of plywood large enough to cover the skimmer wall cutouts against the liner and over the cutouts. From outside the pool, use a razor knife to trim the liner away using the edge of the rectangular wall cutout as a guide. When finished, trim away the liner around the vacuum port cutout in the same manner.
4. Install the upper faceplate u-gasket (9) into the rectangular opening making sure that the liner edges are completely under the gasket. Adjust the gasket so that the flanges lay flat against both the liner and outside pool wall. Punch out the two top corner holes using a nail. Install the lower faceplate u- gasket (10) into the vacuum port opening. Posi-tion the faceplate (15) over the gaskets and insert two large self-threading screws (14) into top corner holes and carefully push the screws through the holes which have been pierced in the liner. From outside the pool, align the skimmer body with these screws. Lightly tighten the two screws (Fig.3).
5. Using a nail and the faceplate as a guide, pierce the 13 additional holes through the liner. Insert and lightly tighten the remaining 13 screws (14) through the faceplate, gaskets, liner, pool wall, and into corresponding holes on the skimmer. Tighten all screws firmly and evenly, alternating left and right, top and bottom. NOTE: The gasket around the vacuum adaptor is required to assure a tight seal around the vacuum adaptor when vacuuming.
6. Attach vacuum port cover (12) and retainer (11) to faceplate using screw (8).

RETURN FITTING INSTALLATION

1. Locate a board large enough to cover the return fitting cutout. From inside of pool, use the board to hold the liner against the cutout in pool wall. Keep hands away from hole to avoid injury. From outside of pool, use the cutout as a guide and cut away the liner with a razor knife.
2. Install the return fitting u-gasket (17) into the wall opening making sure the liner’s edge is trapped under the gasket. Insert the threaded end of the return fitting adaptor (18) through the wall from inside pool.
3. Hold the return fitting body (16) so the hose fitting end points straight up while turning the adaptor from inside the pool. When the adaptor just begins to crush the gasket, hold the adaptor from turning while rotating the body clockwise to its straight down position.
4. If the assembly does not feel snug, rotate the return fitting body back to the up position. Rotate the adaptor inside pool an additional 1/4 turn, then rotate the body to the down position again. Repeat this procedure as required.
5. Install eyeball insert (20) into eyeball (21). Hold the eyeball inside the adaptor (18) with insert toward inside. Thread on the return fitting cover (22) to secure eyeball position so it directs flow away from skimmer opening. Do not overtighten.

CONNECTING SKIMMER TO FILTER
Install the filter and pump as far from the pool wall as possible so they may not be used as steps by children. Instructions in your Filter Owner’s Guide will tell you how to connect the skimmer to the filtering system. Follow those instructions carefully. When you have completed them, refer to your Pool Assembly & Installation Instructions to fill pool. The correct water level will be midway between the two water level marks on the skimmer faceplate. Inspect skimmer installation for leaks when pool is filled. On-going leaks from skimmer or wall fittings may cause pool wall damage which eventually may result in pool wall failure.

CAUTION: Always keep the water level in your pool between the water level markers on the skimmer faceplate. The pump must be able to draw water from the pool to operate. Never run the pump with the pool water level so low that no water passes to the pump. This may cause the pump seal to overheat and permanent damage may occur.

ROUTINE CARE & MAINTENANCE

KEEP YOUR POOL SPARKLING
You can take steps to reduce the amount of maintenance needed to keep your pool sparkling.

1. Provide a clean walkway leading to your pool entrance.
2. Rinse off patio and area around pool regularly.
3. Bathers should rinse off (especially their feet) before entering pool.
4. Maintain the proper chemical balance in your pool. Hot days will cause chemicals to dissipate rapidly.
5. Remove floating leaves and debris with a leaf skimmer.
6. Empty skimmer basket frequently.
7. Vacuum pool bottom to remove settled debris.

POOL CARE
Refer to Embassy PoolCo’s “Safety First Pool Use Handbook” for correct use, care, and chemical
treatment of your pool.

CHLORINE INSTRUCTIONS
ALWAYS READ AND FOLLOW CHEMICAL MANUFACTURER’S SAFETY

PRECAUTIONS FOR HANDLING CHLORINE
WARNING! DO NOT PLACE CHLORINE TABLETS IN THE SKIMMER BASKET! Putting chlorine tablets directly into the skimmer basket will destroy the basket and internal components. We recommend against adding any kind of chemicals directly into the skimmer!Please read the following instructions carefully. Chlorine is a strong chemical. Improper use could result in serious, permanent damage to the pool liner. This damage could include “white spots”, wrinkles or breakage (brittle vinyl). Such damage is not covered under warranty.

IMPORTANT: Pump should always be “ON” when adding any chemicals to pool water.

WITH DISPENSER
Dry Chlorine (tablets, sticks, granules, or powder). Use one of the following types of chlorine dispensers:

• Floating Dispenser: Use only when pump and filter are running. Dispenser must circulate in pool for safe distribution of chlorine.
• Automatic feeder (in-line or off-line).
• Chlorine generator – Approved for use. Releases chlorine from salt.

Ask your Embassy PoolCo dealer to recommend the best type of dispenser for your pool and area conditions. Follow manufacturer’s instructions for correct use.

WITHOUT DISPENSER
Dry Chlorin e: Use granules or powder only. Never pour dry chlorine directly into the pool water. Mix with pool water in a clean plastic container following chlorine manufacturer’s safety instructions. When all chlorine has dissolved, pour solution into pool water at the return fitting. Water returning to the pool will properly distribute chlorine.
Liquid Chlorine: Liquid chlorine concentrate may be poured directly into pool water. Carefully add liquid chlorine to water at the return fitting. Water returning to the pool will distribute the chlorine. Follow chemical manufacturer’s instructions for use of liquid chlorine.

EMPTY SKIMMER BASKET
Stop pump. Remove skimmer lid (2) to clean skimmer basket (1). CAUTION: Before lifting basket out, check for “STILL ALIVE” insects such as hornets, bees, etc. that could sting you. Then slowly lift basket out and empty it. Replace basket and lid. Start pump to resume normal skimmer operation. Clean basket regularly.

VACUUMING
Empty the skimmer basket prior to vacuuming. Clean the filter following manufacturer’s instructions.

1. Stop pump. Assemble vacuum head, handle and hose (A good smooth bore 1-1/2″ hose will give the best vacuuming results). Attach free end of hose to the double tapered end of vacuum adaptor (13).
2. Start pump. Hold the free end of the hose against the return fitting discharge. This will force air from the hose. When the bubbles cease to rise from the vacuum head, all the air is removed. (Fig. 5 and Fig. 6). Stop pump.
3. Bend the vacuum port cover (12) to the down position. Insert the tapered end of the vacuum adaptor with hose attached into exposed opening using a twisting motion. (Fig. 7).
4. The lid (2) performs two functions. In normal position, it covers the top of the filter. During vacuuming, this same lid becomes the sealing plate for the vacuuming. Be sure pump is “OFF”. Remove the lid, rotate it 90° and lower it inside (handle grip up) to rest above the basket. Make  sure air is not trapped under the lid. Trapped air will cause the lid to rise. CAUTION : Never attempt to install the lid in the vacuuming position while your pump is running. The lid may suddenly be drawn down into position due to the pump’s high suction action. You may injure your hands or fingers.
5. With the lid in place, start pump and operate vacuum over pool floor.
6. When finished vacuuming, stop pump. Remove the vacuum hose with vacuum adaptor attached from the pool. Clean the skimmer basket and your filter. Move the lid to the original position on top of the skimmer. Start pump to resume normal skimmer operation.

WINTERIZING (FREEZING CLIMATES)
We strongly recommend, for the protection of your skimmer, liner and pool wall, that you purchase and install the Winterizing Kit, see local dealer .This kit will allow removal and storage of your skimmer and filtering system, and should eliminate any possibility of damage due to winter peril. CAUTION: Removing the skimmer without installing a winterizing kit is very dangerous to the pool wall, liner, and pool installation, and voids any warranty. Filter damage caused by freezing temperatures is not covered by product warranty.

1. Drain pool to 6 inches below the eyeball return fitting.

2. Remove skimmer from pool, clean and store.

3. Install the Winterizing Kit per Kit instructions.

4. Remove the return fitting eyeball by unscrewing the cover. Replace the eyeball with the shut-off disc (18) and reinstall the cover.
   NOTE : The shut-off disc can be useful for plugging off the return fitting should maintenance be required on the filter or pump.

5. For spring start-up, follow instructions under SKIMMER INSTALLATION in this guide.

REPAIR & MAINTENANCE
Contact your local Embassy PoolCo dealer for original replacement parts. Retain this owner’s guide for reference when ordering parts. Periodically inspect faceplate screws for tightness. Retighten if loose.

EXPLODED PARTS

MODEL 5-2091-013 PARTS LIST (Beige)

ITEM| P/N| QTY| DESCRIPTION| ITEM| P/N| QTY| DESCRIPTION
1| 1300-1002| 1| Skimmer Basket Assy.| 14| 330-1004| 15| #12 x 27/32″ Screw
2| 1107-1357| 1| Standard Skimmer Lid w/Decal| 15| 340-1274| 1| Faceplate
3| 1121-2016| 1| Skimmer Body w/Decal| 16| 340-1773| 1| Return Fitting Body
4| 360-1794| 1| Caution Label| 17| 307-1031| 1| Return Fitting U-Gasket
5| 1121-1358| 1| Weir Float| 18| 340-1237| 1| Return Fitting Adaptor
6| 340-1600| 1| Weir Hinge| 19| 340-1240| 1| Shut-off Disc
7| 1107-1275| 1| Standard Weir Assy.| 20| 340-1278| 1| Eyeball Insert
8| 330-1008| 4| #8 x 1/2″ Screw| 21| 348-1027| 1| Eyeball
9| 307-1029| 1| Upper Faceplate U-Gasket| 22| 340-1238| 1| Return Fitting Cover
10| 307-1030| 1| Lower Faceplate U-Gasket| 23| 360-2106| 1| Operating Instructions Label
11

12

13

| 340-1271

348-1028

340-1253

| 1

1

1

| Vac Port Cover Retainer Vac Port Cover

Vacuum Adaptor

| 24

25

| 365-2031| 1

1

| Owner’s Guide Warranty Card

IMPORTANT FILTER/PUMP SAFETY

1. DO NOT install pump on a deck. It could fall into the water, causing severe electrical shock. Do not install on any surface at, above, or slightly below the top rail of the pool.
2. DO NOT allow children or adults to climb, sit, or stand on the filter or pump units. They could easily fall. Position filter and pump approximately five (5) feet from pool wall so they may not be used as steps by children.
3. CAUTION pool users to stay away from the skim-mer opening. Strong suction can pull hair into the opening, trapping the person and causing injury.
4. FAILURE to keep faceplate mounting screws
   and return fitting tight may cause leakage between skimmer and pool wall. Continued leakage may cause wall damage which eventually may result in pool wall failure.

SERVICING SAFETY TIPS

1. ALWAYS TURN “OFF” the main power switch and the Ground Fault Circuit Interrupter (GFCI) breaker switch so power is completely off before servicing your unit.
2. ALWAYS STOP PUMP before you service, tighten, or adjust the filter assembly.
3. ALWAYS BE SURE THE GROUND UNDER YOUR FEET, AND YOUR BODY, IS DRY before you touch filter or pump electrical equipment. Failure to heed this warning may cause personal injury due to severe electrical shock.
4. ALWAYS have a qualified electrician service your system if electrical problems occur.
5. ALWAYS have a qualified electrician install a Ground Fault Circuit Interrupter (GFCI) breaker at the electrical service or supply panel. Follow GFCI manufacturer’s operating instructions for testing. Failure to do so may cause personal injury due to severe electrical shock.
   CAUTION : To reduce the risk of electrical shock, connect only to grounding type receptacles. A Ground Fault Circuit Interrupter (GFCI) must be provided in accordance with Article 680 of the National Electrical Code (NEC) and local codes or ordinances.
   CAUTION: To reduce the risk of electrical shock, use only Original Equipment Manufactured (OEM) replacement parts when servicing.

IMPORTANT! Misuse of your pool may result in crippling injury and/or other dangers to life and health. Do not Dive or Jump! Do not use slides, diving boards, or any other platform or object which can be used for improper pool entry! Use only an above-ground swimming pool ladder to enter or exit your pool. It is your responsibility to secure your pool against unauthorized, unsupervised or unintentional entry. Always obey all safety rules. Remember, pool safety is everybody’s responsibility.

CHANGE OF DESIGN : Embassy PoolCo expressly reserves the right to change or modify the design and construction of any product in due course of our manufacturing procedures, without incurring any obligation or liability to furnish or install such changes or modifications on products previously or subsequently sold.
Embassy PoolCo • 315 N. Sebastian St. • West Helena, AR 72390

DB 0909-506
Made in the United States of America
Copyright © 2009

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>