Clarke CS400D Digital Electronic Safe Instruction Manual

CAUTION: Do not keep the override keys inside the safe!
DIGITAL SAFE
MODEL NO: CS400D
PART NO: 7710185
OPERATION & MAINTENANCE
INSTRUCTIONS

INTRODUCTION

Thank you for purchasing this CLARKE Digital Safe.
Before attempting to operate the safe, it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you can look forward to the safe giving you long and satisfactory service.

SPECIFICATION

REPLACEMENT OVERRIDE KEY

A small label is located on the front of each safe with a key number. The number will start with either the letter “J” or “G” followed by several digits. This number must be registered with us in the event you require a replacement key.
Please complete the registration form at the back of this manual and send it to the address stated with the form. If you fail to register the safe we will not be able to provide you with a replacement key.
We recommend that in addition to sending the completed form you remove the label from the safe and fix it to the space below. Please retain this document for future reference.
Fix or record the key number here

BEFORE USE

OPENING THE SAFE FOR THE FIRST TIME

1. Remove the small plastic cover (B) on the front panel.

2. Insert the override key into the key hole and turn it counterclockwise, at the same time, turn the doorknob (A) clockwise direction to open the safe.
   NOTE: Never keep the override keys inside the safe itself.

3. Replace the small plastic cover (B) with the front panel.

INSTALLING THE SAFE
The safe should be secured vertically to a wall, shelf, or to the floor using the expansion bolts (supplied).
• There are holes (8 mm) on the rear and bottom of the safe for securing to a wall or the floor.

INSTALLING THE BATTERIES
The safe requires 4 x size “AA” (1.5V) batteries.

1. Open the safe.
2. Remove the battery cover plate on the back of the door and install the batteries.
3. Ensure the batteries are fitted with the correct polarity.
4. The use of alkaline batteries is recommended.

PROGRAMMING THE CODE

1. With the safe door open and the batteries installed.

2. Press and release the red button on the rear of the lock housing.
   • you will hear two beeps.
   • The yellow light will be on at the same time.

3. Enter the code you want to use (3-8 digits) as a combination.

4. Confirm within 15 seconds by pressing the letter “A” or “B”.
   • The safe “bleeps” twice and the yellow light will go off, your personal code is now set.

5. Test the safe using the new combination immediately.

USING YOUR SAFE

TO OPEN THE SAFE

1. Enter your personal code followed by the letter “A” or “B”.
   • you will hear a beep and the green light on the front of the safe will light up.

2. Turn the doorknob in a clockwise direction to open the door within 5 seconds.
   • If you, or an intruder uses the incorrect group of numbers, it will not open, if the incorrect combination is used 3 times consecutively, you must wait for 20 seconds before trying again.
   • If the incorrect combination is selected a further 3 times, you must wait approximately 5 minutes before trying again.
   BATTERY REPLACEMENT WARNING
   If the batteries are low, the red light (in the middle of the number panel) will illuminate.
   MANUAL OVERRIDE
   • See “Opening the safe for the first time” on page 3.

DECLARATION OF CONFORMITY

Hymnal Street.Epping.Essex CM16ALG
DECLARATION OF CONFORMITY
This is an important document and should be retained.

We hereby declare that this product(s) complies with the following UK legislation: Supply of Machinery (Safety) Regulations 2008.
The following standards have been applied to the product(s): EN ISO 12100:2010, EN 11148-6:2012.
The technical documentation required to demonstrate that the product(s) meet(s) the requirement(s) of the aforementioned legislation has been compiled and is available for inspection by the relevant enforcement authorities.
This product was placed on the market: in 2013
Product Description: Air Impact Wrench
Model number(s) : CAT23C
Serial batch Number : N/A
Date of Issue : 25/02/2021
Signed:

Fitzwilliam Hall Fitzwilliam Place, Dublin 2
DECLARATION OF CONFORMITY
This is an important document and should be retained.

We hereby declare that this product(s) complies with the following directive(s):
2006/42/EC Machinery Directive.
The following standards have been applied to the product(s):
EN ISO 12100:2010, EN 11148-6:2012.
The technical documentation required to demonstrate that the product(s) meet(s) the requirement(s) of the aforementioned directive(s) has been compiled and is available for inspection by the relevant enforcement authorities.
The CE mark was first applied in 2013
Product Description: Air Impact Wrench
Model number(s): CAT23C
Serial/batch Number: N/A
Date of Issue : 25102/2021
Signed:

A SELECTION FROM THE VAST RANGE OF

| QUALITY PRODUCTS
AIR COMPRESSORS
From DIY to industrial, Plus air tools, spray guns, and accessories.
GENERATORS
Prime duty or emergency standby for business, home, and leisure.
POWER WASHERS
Hot and cold, electric and engine driven – we have what you need
WELDERS
Mig, Arc, Tig, and Spot. From DIY to auto/industrial.
METALWORKING
Drills, grinders, and saws for DIY and professional use.
WOODWORKING
Saws, sanders, lathes, mortisers, and dust extraction.
HYDRAULICS
Cranes, body repair kits, and transmission jacks for all types of workshop use.
WATER PUMPS
Submersible, electric, and engine-driven for DIY, agriculture, and industry.
POWER TOOLS
Angle grinders, cordless drill sets, saws, and sanders.
STARTERS/CHARGERS
All sizes for car and commercial use.|
PARTS & SERVICE: 0208 988 7400
Parts Enquiries Parts@clarkeinternational.com
Servicing & Technical Enquiries Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
INTERNATIONAL Hemnall Street, Epping, Essex CM16 4LG
www.clarkeinternational.com

IMPORTANT
In order to be able to obtain a replacement key.
Please detach and complete this safe registration form (see reverse), Then return it to:
Clarke International
Product Registration Department
Shrubland Road
London
E10 7RB

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>