Zhongshan B03-BB03B ELECTRONIC BABY AND MOTHER SCALE User Manual

Zhongshan B03-BB03B ELECTRONIC BABY AND MOTHER SCALE

Device instruction

• Scale body
  Weighing scale.

• Detachable Trays
  Assembly two pieces of detachable trays together to a full tray for baby weighing.

• Assembly groove
  To put trays in.

• ON/OFF/ Tare button

  •  Press the button to switch on/off the scale;
  •  Press the button “Tare”, if you put a towel on the scale before put baby
    on it, make the display back to 0.00.

• Unit button

  •  Press the button to switch unit: kg / lb / st:lb.
  •  Long press (2~3 seconds) the button to change the display direction.

Product Specification

1.  Size: 650x320x88mm
2. Material: Full ABS plastic.
3.  Capacity: 20KG for baby weighing mode; Max. 200kg for adult mode.
4.  Accuracy: D=5g (Weight in 50g~20kg); D=50g (weight in 20kg~120kg).
5.  Unit: kg, lb, st:lb.
6.  Touch ON/OFF.
7.  4 high precision strain gauge sensors.
8.  Tare function.
9.  Auto-lock/hold function (easier weighing of moving babies-the result is automatically locked weight).
10.  Low battery and overload indication.
11.  LED display size: 90x26mm.
12. Touch switch display direction.
13.  Power: 3×1.5V AAA battery

Device Installation

• Trays Installation for baby used
  • to lace the scale on hard & flat surface. Do not weight on carpet or any soft surface as it may affect accuracy.
  • Put two pieces of split trays into each groove, make trays in a parallel line, be sure they are in the right place perfectly, then pull two trays in opposite direction.
  • Press the safety buckle, to lock trays.
• Trays Disassembling
  • ull the safety buckle.
  • Pull two trays in opposite directions to split them.
  • Pick up the trays, and stock them in dry and flat place
• Insert Battery )Insert the batteries (3×1.5V AAA) into the battery compartment, then put on the battery cover. Make sure the positive and negative contacts are properly aligned. Remember to take off all batteries if no used scale in a long time, to protect the Scale

Device Operation

1.  Weight in baby mode
2.  Please use the scale one the hard & flat surfaces. Do not weigh on the carpet or any soft surface as it may affect accuracy;
3.  Insert batteries, press the “ON/OFF” button to turn on scale;
4.  Assembly trays perfectly, as above Part II1-1 instruction;
5. After the display comes” 0.009″, long-press the “UNIT” button to make the display direction as same as reader s side;
6. Put baby on the trays safety to weighting

• Auto-lock function

  •  Please use the sc face. Do not weight on carpet or any soft surface as it may affect accuracy;
  •  Insert batteries, press “ON/OFF” button to turn on scale;
  •  Assembly trays perfectly, as above Part -1 instruction;
  • After display comes “ 0.00kg ” , long press “UNIT” button to make the display direction as same as reader’ s side;
  • Put baby on the trays safety to weighting; Do not move baby off from the tray when scale is working, the data will auto lock aft kers.

• Reset and tare function

  •  Press “TARE” if you need to put a towel/cloth on the tray before baby in,make the display turns to “ 0.00 ”.
  •  Press “TARE”, if data is locked and keep the last one when you need to weight another baby, make display turns to “ 0.00” , then put a new baby on it. ( this function is repeatable)

• Overload Indication
  If the weight is over loaded “max capacity”, LED display shows “ O-LD ”.

• Low Power Indication
  When LCD display shows “ LO ”, Please replace the new battery with correct polarity.

• Auto Off without any operation after 60 seconds.

Weight in Mother mode

1.  Please use the sc face. Do not weigh on carpet or any soft surface as it may affect accuracy;
2.  Disassembling trays as above Part -2 instruction;
3.  Insert batteries, press the “ON/OFF” button to turn on scale;
4. After display comes “ 0.00kg ” , long press “UNIT” button to make the display direction as same as reader’ s side;
5.  Stand on the scale surface to weighting.

Connect with AiLink APP

1.  Open the APPand the Bluetooth of the phone.After entering the APP,click the “+” button in the right corner as shown in Figure 1.
2.  The APP automatically scans nearby devices when entering the interface to add devices,as shown in Figure 2.
3.  Click the scanned device to add automatically,and it will be displayed after successful addition as shown in Figure 3.
4.  Select the weighing position on the APP and click “Start using”.
5.  Set the units on the APP.
6.  Select or add family members that eed to be measured in the APP.
7. The device is connected successfully,please start measuring on the upper scale.

Safety precautions

1. When in use, the scale should be placed on flat,dry and hard surface.
2. Use to this device for its intended purpose at home.
3. Do not overload the scale’s capacity, the max.is 120kg.
4. Avoid shaking or hitting the scale.
5. Do not submerge in water.
6. When in storage, do not place anything on the scales
7. The optimal temperature for operating and storing the scales is 5 C-40C.

References

• Heimilistæki | HT.is

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>