Goldair GCT330 2400W Ceramic Tower Heater with WiFi SMART HOME User Manual
- June 5, 2024
- GOLDAIR
Table of Contents
GCT330 2400W Ceramic Tower Heater with WiFi SMART HOME
User Manual
Operating Instructions
2400W CERAMIC TOWER HEATER WITH WIFI/SMART HOME
Model: GCT330
General Care and Safety Guide
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS ARE OUTLINED IN THIS MANUAL.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they are supervised or have been given instruction concerning the use of the appliance by a person responsible for their safety.
-
Children should be supervised to ensure that they do not play with the appliance.
-
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
WARNING: You must not cover this appliance. Covering this appliance presents a fire risk and will activate the safety fuse; permanently disabling the unit.
WARNING: Do not use this appliance in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.
WARNING: To reduce the risk of fire, keep textiles, curtains, or any flammable material a minimum distance of 1 meter from the air outlet. -
Use only the voltage specified on the rating label of the appliance.
-
Keep all objects at least 1 meter from the front, sides, and rear of the appliance.
-
This appliance is intended for household use only and not for commercial or industrial use.
-
Indoor use only.
-
Use this appliance only as described in this manual. Any other use is not recommended by the manufacturer and may cause fire, electric shock or injury.
-
Do not use the appliance if it has been dropped or damaged.
-
The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills.
-
Never use the appliance to dry clothes.
-
Always unplug appliances when not in use.
-
When the appliance has been unpacked, check it for transport damage and ensure all parts have been delivered. If parts are missing or the appliance has been damaged, contact the Customer Services Team.
-
Do not use if there are visible signs of damage to the appliance.
-
Do not connect the appliance to the main supply until completely assembled and adjusted.
-
Ensure hands are dry before handling the plug or main unit.
-
Ensure the appliance is on a flat, stable, heat-resistant surface.
-
Do not operate with the cord set coiled up as a heat build-up is likely, which could be sufficient to become a hazard.
-
Carry out regular checks of the supply cord to ensure no damage is evident
-
Do not operate this appliance with a damaged cord, plug, or after the appliance malfunctions or has been dropped or damaged in any manner. Take to a qualified electrical person for examination, electrical service, or repair.
-
Do not twist, kink, or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always ensure that all cord has been removed from any cord storage area and is unrolled before use.
-
It is recommended that this appliance is plugged directly into the wall socket. Power boards are not rated to supply power to high-wattage appliances.
-
A correctly specified, an undamaged extension cord may be used with this appliance provided it is used in a safe manner.
-
Do not remove the plug from the power socket until the appliance has been switched off.
-
Do not remove the plug from the power socket by pulling the cord; always grip the plug.
-
Do not place a cord under the carpet or cover it with rugs or furniture. Arrange the cord so it cannot be tripped over.
-
Don’t place appliances on bedding or on thick & long carpet where the openings may get blocked.
-
Switch off and use the handle provided when moving
-
Do not place the appliance close to a radiant heat source.
-
Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire, or damage to the appliance.
-
Do not sit on the appliance.
-
Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) and rinsed in hot soapy water only. Always remove the plug from the mains supply before cleaning.
-
Do not operate in areas where petrol, paint, or other flammable liquids are used or stored.
-
Do not use this appliance in the immediate surroundings of a bath, a shower, a swimming pool, or other liquids.
-
The appliance must not be immersed in any liquids.
-
There are no user-serviceable parts installed in the unit.
-
Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards.
-
This unit is not supposed to be used in or around locations where foodstuffs, works of art or delicate articles of science, etc. are stored.
-
If your appliance does not work or is not working properly, contact the place of purchase or the Customer Services Team.
-
The remote control supplied with this appliance uses a 2 x AAA battery.
Operating Your Heater
Always choose a safe location for the heater, keeping in mind the safety
precautions outlined. Ensure all packaging has been removed from the unit
before use. Please follow the below instructions.
WARNING: In order to avoid overheating or fire, do not cover the heater.
WARNING: Keep all objects at least 1 meter from the front, sides, and
rear of the appliance.
WARNING: Do not use this heater with a programmer, separate timer,
remote-control system, or any other device that switches the heater on
automatically, since a fire risk exists if the heater is covered or positioned
incorrectly.
WARNING: Never leave this heater unattended when in use. Ensure the
heater is on a flat, stable, heat-resistant surface. Once the heater is in a
safe operating position and all switches are in the off position, insert the
power plug into the main outlet and switch it on.
CAUTION: Ensure the power cord is not tight because if pulled it may
partially pull the plug from the socket. A partially inserted plug will
overheat the plug and socket and could result in fire.
HEATER CONTROL
Ensure the heater is on a flat, stable, heat-resistant surface. Once the
heater is in a safe operating position and all switches are in the off
position, insert the power plug into the main outlet. Turn the Power Switch at
the back of the heater to the ‘I’ position. The heater is now in STANDBY mode.
The heater can be operated by the touchscreen control panel, remote control or
via the Goldair App. When an operation has been selected, the relevant LED
light on the control panel will display.
– ON/OFF: Turns the heater ON/OFF while in STANDBY mode. The LED light
will display the current room temperature and begin to blow out room
temperature air. After turning the unit OFF, the fan will continue to run for
about 30 seconds to reduce the residual heat inside the unit. After 30
seconds, the heater device will stop running. Do not remove the plug directly
while the power is still running to avoid damaging the device.
– ‘+’ and ‘ -‘ : Increase/Decrease the desired temperature and puts the
heater into Auto (Ai) mode. When the temperature is set more than 4 higher
than the room temperature, the heater will run on high mode. When the set
temperature is equal to or less than 4 higher than the room temperature, the
heater will run on low mode. When the set temperature is equal to or lower
than the room temperature, the heater will run on fan mode and blow out room
temperature air.
– MODE : Change the mode between Low heat, High heat, and Fan.
– TIMER: Turns on Timer. When the heater is ON, use the Timer to set the
timer to turn the heater OFF. This will activate the Timer’ LED. When the heater is OFF, use the Timer to set the timer to turn the heater ON. This will activate theReservation’ LED. Increase timer amount by 1 hour each time you
press the TIMER button, up to a maximum of 9 hours. Use the ‘+’ and ‘’
controls to set the desired temperature, and once the LED stops flashing the
timer function has been set.
– SWING: Turns oscillation ON/OFF
WiFi Downloading and Setting up APP
This APP is supported only on 2.4GHz Wi-Fi channels. Please ensure your
phone is 2.4GHz capable
Note this device will only work within your home WIFI system.
This does not operate on 3G or 4G internet connections.
You will need a connection to your home Wi-Fi.
Download the Goldair mobile AP
- Open the APP Store or Google Play on your mobile phone.
- Open ‘Search’ and enter ‘Goldair’
- Click ‘GET’ and begin to download and install.
Once downloaded to your phone open the APP
- Tap REGISTER near the bottom of the screen.
- Read and agree to the Privacy Policy.
- Add your email address.
- Tap ‘Obtain verification code’
You will then receive an email with a verification code.
- Enter the verification code from your email.
- Create a password.
- Then tap confirm.
If you haven’t received a verification code via email, tap the resend button,
and when the verification code is received follow the above steps.
Your APP is now registered and ready for pairing to your device.
Pairing APP to Heater
Details for pairing this heater to the Goldair App can be found at the below website link. Either scan the QR code below or enter the website into your browser.
https://goldair.co.nz/goldair-app
Operating Your Heater
SAFETY devises
This appliance has three protection devices:
- Tilt Switch – this will automatically turn the appliance off if the appliance is not in the correct operating position.
- Resettable Thermal Link – this will automatically disconnect the power to the appliance at a pre-set overheat temperature. After cooling down it will reset and power on again. If this occurs, investigate what is causing the appliance to overheat.
- Thermal Fuse – this disconnects the appliance permanently in case of overheating. (It is nonresettable).
CAUTION: The appliance generates heat during use. Precautions must be taken to prevent the risk of burns, scalds, fires or other damage to persons.
CARE AND CLEANING
The heater requires regular cleaning to ensure trouble-free operation:
- Unplug the heater from the mains supply before cleaning.
- Ensure that the heater has been allowed to cool down completely before cleaning.
- The common cause of overheating is deposits of dust or fluff in the appliance.
- Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills.
- Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and dirt.
- Never use solutions such as petrol, thinners, or polishing agents. ·
- Ensure the heater is dry before plugging back into the main supply.
- Do not attempt to dismantle the heater. · There are no user-serviceable parts. For service or repair, contact an authorized electrical service technician.
PROOF OF PURCHASE
To receive a warranty retain the receipt as proof of purchase.
TECHNICAL SPECIFICATION
Model No: GCT330
Supply: 230-240VAC 50Hz
Wattage: 2300-2400W
SUPPORT AND TECHNICAL ADVICE
Goldair New Zealand
Monday Friday 8 am-5 pm
Phone +64 (0)9 917 4000
Phone 0800 232 633
info@cdb.co.nz
Goldair Australia
Monday Friday 8 am-5pm
Phone +61 (0)3 9365 5100
Phone 1300 465 324
info@cdbgoldair.com.au
Two Year Warranty
Thank you for purchasing this Goldair product. Your product is warranted
against faults and manufactured when used in normal domestic use for a period
of two years. For non-domestic use, Goldair limits the voluntary warranty to
three months.
Goldair undertakes to repair or replace this product at no charge if found to
be defective due to a manufacturing fault during the warranty period.
This warranty excludes damage caused by misuse, neglect, shipping accident,
incorrect installation, or work carried out by anyone other than a qualified
electrical service technician.
PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY.
The benefits given to you by this warranty are in addition to other rights and
remedies available to you under the law in relation to the goods or services
to which this warranty relates.
In Australia, our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure.
In New Zealand, this warranty is additional to the conditions and guarantees
of the Consumers Guarantee Act (1993).
Goldair New Zealand
DB Goldair PO Box 100-707
N.S.M.C
Auckland
Phone +64 (0)9 917 4000
Phone 0800 232 633
www.gold air.co.nz
Goldair Australia CDB Goldair Australia Pty
PO Box 574 South Morang Victoria, 3752
Phone +61 (0)3 9365 5100
Phone 1300 GOLD AIR (1300 465 324)
www.goldair.com.au
Goldair Two-Year Warranty (IMPORTANT: Please complete and retain this
warranty card)
Name………………………………………………………..
Address……………………………………………………….
Place Of Purchase……………………………………..
Name Of Product………………………………………
Attach a copy of the purchase receipt to this warranty card
Date Of Purchase…………………………………….
Model Number………………………………………………….
Due to continual design improvements, the product illustrated in this User
Manual may differ slightly from the actual product.
New Zealand
PO Box 100707,
North Shore Mail Centre,
Auckland, 0745
www.goldair.co.nz
Australia PO Box 574,
South Morang, Victoria, 3752
www.goldair.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>