neat NFD1 Bar Pro Pad Zoom Rooms System User Manual
- June 5, 2024
- neat
Table of Contents
NFD1 Bar Pro Pad Zoom Rooms System
User Manual
Neat Bar Pro packs a stack of tech into a simple and elegant slimline device.
It’s capable of driving three large screens, has two extreme resolution
cameras, a multiple microphone array, and three full-range speakers.
Ideal for delivering superior-quality audio, video, and other unique capabilities to your huddle, focus, the meeting, and conference rooms, Neat Bar Pro comes with a dedicated Neat Pad controller and integrated environmental sensors.
Simple setup
All you need is in the box.
including mounts. cables and clear instructions. So it’s easy for anyone to
install and set up, above or below one. two or three screens. 
Neat Bar Pro
Neat Bar comes with everything you need to get started, including cables. wall mount. screen mount and table stand.
In the box
Neat Bar Pro: Video conferencing device
HDMI cable: 6.5ft (2m)
Ethernet cable: 9.8ft (3m)
Power cord: 9.8ft (3m)
Mount adapter. wall mount. screen mount and table stand
4x M8 screw (0.94 in / 24 mm) for VESA mount
4x M6 screw (0.94 in / 24 mm) for VESA mount
2 x spacer (to secure parallel TV mount)
15 mm hex key for the screen mount
1×2 mm hex key for the mount adapter
2 additional screw bags for dual or triple screen setup
4x M8 screw (0.94 in / 24 mm) for VESA mount
2 x 4x M6 screw (0.94 in / 24 mm) for VESA mount
4x spacer (to secure alignment of all screens)
Screws for mounting to the wall are not included. Mounting on a wall should only be performed by qualified personnel in line with applicable facility and state regulations. The wall and the mounting equipment must safely withstand the load of the product.
Neat Pad
Neat Pad works as a Controller for Neat Bar and can also be configured as a Scheduling Display for the Meeting Room. It comes with everything you need to get started, including cables and mounting options.
In the box
Neat Pad: 8-inch touch screen
2 x Ethernet cable: 9.8ft (3m) + 16.4ft (5m)
PoE power adapter
Mount adapter, side mount, and wall mount| 4M4 screw (0.30 in / 7.5 mm) for
the wall mount
3M4 screw (0.19 in / 4.7 mm) for the side mount
12.5 mm hex key for the adapters
1×2 mm hex key to secure Neat Pad to the wall mount
---|---
Screws for mounting to the wall are not included. Mounting on a wall should only be performed by qualified personnel in line with applicable facility and state regulations. The wall and the mounting equipment must safely withstand the load of the product.
Mounting & releasing
Mounting
Slide Neat Bar onto the selected mounting option (1). When fully inserted tilt
Neat Bar back to horizontal and check if it is secure by carefully pulling it
towards you. 
Releasing
Tilt Neat Bar fully forward (1). Pull towards you (2) until the unit stops and
the red release lever appears (3). Push the release lever up and pull Neat Bar
gently off the mount adapter.
Size & weight
Neat Bar Pro
| Width: 35.04 in (890 mm) | Depth: 3.15 in (80 mm) |
|---|---|
| Height: 3.15 in (80 mm) | Weight: 6.83 pounds (3.1 kg) |
Neat Pad
| Width: 7.8 in (198 mm) | Depth: 5 in (127 mm) |
|---|---|
| Height: 1.7 in (42 mm) | Weight: 1.15 pounds (520 g) |
Setup & connectivity
Setup
Use the provided cables to set up Neat Bar. Connect the cables according to
the illustration. Cables marked – are included. Cables marked – – – – are
optional and not required for basic use of the system.
Requirements for a complete setup
Display Internet connection Video service 
Environmental Requirements
Ambient operating temperature: 32° to 95° F (0°- 35° C)
Storage temperature: 5° – 149° F (-15° – 65° C)
Relative humidity: 20% to 80%
Network standby: <8W (after 20 minutes)
Additional Product Information
https://neat.no/bar-pro
Neat Bar Pro and Neat Pad – User Manual rev02