TROTEC PSCS 11-20V Cordless drill driver User Manual
- June 5, 2024
- TROTEC
Table of Contents
PSCS 11-20V Cordless drill driver
PSCS 11-20V
EN
ORIGINAL INSTRUCTIONS CORDLESS DRILL DRIVER
TRT-BA-PSCS11-20V-TC2016-16-007-EN
Table of contents
Notes regarding the instructions …………………………………… 2 Safety
…………………………………………………………………………. 2 Information about the device………………………………………… 8
Transport and storage………………………………………………… 10 Start-
up…………………………………………………………………….. 10 Operation ………………………………………………………………….. 14
Available accessories…………………………………………………. 16 Errors and
faults………………………………………………………… 16 Maintenance ……………………………………………………………… 17
Disposal ……………………………………………………………………. 17
Wear safety glasses Information marked with this symbol indicates that you
should wear eye protection.
Wear a protective mask Information marked with this symbol indicates that you
should wear a protective mask.
Wear protective clothing Information marked with this symbol indicates that
you should wear protective clothing.
Wear protective gloves Information marked with this symbol indicates that you
should wear protective gloves.
You can download the current version of the instructions and the EU
declaration of conformity via the following link:
Declaration of conformity …………………………………………… 18
PSCS 11-20V
Notes regarding the instructions
Symbols
Warning of electrical voltage This symbol indicates dangers to the life and
health of persons due to electrical voltage.
Warning of explosive substances This symbol indicates dangers to the life and
health of persons due to potentially explosive substances.
Warning This signal word indicates a hazard with an average risk level which,
if not avoided, can result in serious injury or death.
Caution This signal word indicates a hazard with a low risk level which, if
not avoided, can result in minor or moderate injury.
Note This signal word indicates important information (e.g. material damage),
but does not indicate hazards.
Info Information marked with this symbol helps you to carry out your tasks
quickly and safely.
Follow the manual Information marked with this symbol indicates that the
instructions must be observed.
https://hub.trotec.com/?id=42025
Safety
General Power Tool Safety Warnings
Warning Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury. Save all warnings and instructions for future reference. The term
power tool in the warnings refers to your mainsoperated (corded) power tool or
battery-operated (cordless) power tool.
General Power Tool Safety Warnings Work area safety
· Keep work area clean and well lit. Clutter or dark areas invite accidents.
· Do not operate power tools in explosive atmosphere, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may
ignite the dust or fumes.
· Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2
cordless drill driver PSCS 11-20V
EN
General Power Tool Safety Warnings Electrical safety
· Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
· Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
· Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
· Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
· When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
· If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
General Power Tool Safety Warnings Personal safety
· Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective
equipment such as a dust mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce personal injuries.
· Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
· Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
· Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situation.
· Dress properly. Do not wear loose clothing or jewellery. Keep your hair and
clothing away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
· If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
· Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause
severe injury within a fraction of a second.
General Power Tool Safety Warnings Power tool use and care
· Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
· Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must be
repaired.
· Disconnect the plug from the power source and/or remove the battery pack, if
detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
· Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
· Maintain power tools and accessories. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
· Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
· Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
EN
cordless drill driver PSCS 11-20V
3
· Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
General Power Tool Safety Warnings Battery tool use and care
· Recharge only with charger specified by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of fire when used with
another battery pack.
· Use power tools only with specifically designed battery packs. Use of any
other battery packs may create a risk of injury and fire.
· When battery pack is not in use, keep it away from other metal objects, like
paper clips, coins, keys, nails, screws or other small metal objects, that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
· Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
· Do not use a battery pack or tool that is damaged or modified. Damaged or
modified batteries may exhibit unpredictable behaviour resulting in fire,
explosion or risk of injury.
· Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or temperature above 130 °C may cause explosion.
· Follow all charging instructions and do not charge the battery pack or tool
outside the temperature range specified in the instructions. Charging
improperly or at temperatures outsides the specified range may damage the
battery and increase the risk of fire.
General Power Tool Safety Warnings Charger use and care
· This charger can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
· Never insert non-rechargeable batteries into the charger. A charger that is
suitable for one type of battery pack may create a risk of fire and explosion,
when used with another battery pack or non-rechargeable batteries.
· Only charge the Li-Ion battery “Multiflex 20 2.0 DC” (capacity of 2.0 Ah =
5 battery cells) with the charger “Multiflex 20 2.0 AC”. The battery voltage
must match the battery charging voltage of the charger.
General Power Tool Safety Warnings Service
· Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
· Never service damaged battery pack. Service of battery packs should only be
performed by the manufacturer or authorized service providers.
Device-specific safety warnings for cordless drill drivers
· Secure the workpiece. The grip of tensioning devices or a vice is more
secure than holding the workpiece only by hand.
· Hold the power tool firmly. When tightening or loosening screws, high
reaction torques can occur temporarily.
· Immediately switch off the power tool if the insertion tool blocks. Beware
of high reaction torques causing a kickback.
· Hold the power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory or fasteners may contact hidden wiring.
Cutting accessory contacting a “live” wire may make exposed metal parts of the
power tool “live” and could give the operator an electric shock.
· For any work on the device, as well as during transport or storage, set the
switch for the rotational direction to centre position (locked). This prevents
unintentional starting of the power tool.
· Regularly check the tool holder for wear or damage.
· Wait until the power tool has come to a standstill, before putting it down.
4
cordless drill driver PSCS 11-20V
EN
Safety instructions when using long drill bits
· Never operate at higher speed than the maximum speed rating of the drill
bit. At higher speeds, the bit is likely to bend if allowed to rotate freely
without contacting the workpiece, resulting in personal injury.
· Always start drilling at low speed and with the bit tip in contact with the
workpiece. At higher speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in personal injury.
· Apply pressure only in direct line with the bit and do not apply excessive
pressure. Bits can bend causing breakage or loss of control, resulting in
personal injury.
Intended use Only use the device PSCS 11-20V: · for screwing in and loosening
screws, · for drilling in wood, plastic, ceramic and metal, whilst adhering to
the technical data. We recommend using the power tool with original Trotec
accessories.
Foreseeable misuse The device is not intended for drilling in concrete or
natural stone. Any other use than the one described in the chapter “Intended
use” is regarded as reasonably foreseeable misuse.
Personnel qualifications People who use this device must: · have read and
understood the instructions, especially the
Safety chapter.
Safety signs and labels on the battery and the charger
Note Do not remove any safety signs, stickers or labels from the device. Keep
all safety signs, stickers and labels in legible condition.
The following safety signs and labels are attached to the battery:
Warning of explosion risk! These symbols indicate the following: Do not expose
the battery pack or tool to fire or excessive temperature! Do not let the
battery come into contact with water or fire! Avoid direct sunlight and
moisture. There is a risk of explosion!
Never charge the battery at ambient temperatures below 10 °C or above 40 °C.
Charging improperly or at temperatures outsides the specified range may damage
the battery and increase the risk of fire.
Observe the correct disposal of the battery! This symbol indicates the
following: Ensure that the battery is disposed of correctly and never dispose
of it in waste water or public waters. The battery contains irritating,
caustic and toxic substances that pose significant risks to people and the
environment.
The following safety signs and labels are attached to the charger:
This symbol indicates the following: Read the instructions or operating manual
before charging the battery.
This symbol indicates the following: Only use the charger for charging the
battery in dry interior spaces. Do not charge the device outdoors.
EN
cordless drill driver PSCS 11-20V
5
Personal protective equipment
Wear eye protection. With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.
Wear a protective mask. It saves you from inhaling harmful dusts generated
when processing workpieces.
Wear protective gloves. They protect your hands from burns, crushing injuries
and skin abrasions.
Wear tight-fitting protective clothing. This protects you from the draw-in and
entanglement hazard posed by rotating parts.
Residual risks
Warning of electrical voltage Electric shock from insufficient insulation.
Check the device for damages and proper functioning before each use. If you
notice damages, no longer use the device. Do not use the device when the
device or your hands are damp or wet!
Warning of electrical voltage Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage Before any work on the device, remove the mains
plug from the mains socket and the battery from the device! Hold onto the
mains plug while pulling the power cable out of the mains socket.
Warning of electrical voltage There is a risk of a short-circuit due to
liquids penetrating the housing! Do not immerse the device and the accessories
in water. Make sure that no water or other liquids can enter the housing.
Warning of explosive substances Do not expose the battery to temperatures
above 45 °C! Do not let the battery come into contact with water or fire!
Avoid direct sunlight and moisture. There is a risk of explosion!
Warning of hot surface The insertion tool might still be hot after the
application. Burn hazard when touching the insertion tool. Do not touch the
insertion tool bare-handed! Wear protective gloves!
Warning Toxic dusts! The harmful / toxic dusts produced during operation pose
of risk to the health of the operator and persons in the vicinity. Wear eye
protection and a dust mask!
Warning Do not process materials containing asbestos. Asbestos is considered
carcinogenic.
Warning Make sure not to hit power, gas or water lines when working with a
power tool. If necessary, use a pipe detector to check the wall you want to
drill in or slit open.
Warning Risk of injuries caused by flying parts or bursting tool heads.
Warning Dangers can occur at the device when it is used by untrained people in
an unprofessional or improper way! Observe the personnel qualifications!
Warning The device is not a toy and does not belong in the hands of children.
Warning Risk of suffocation! Do not leave the packaging lying around. Children
may use it as a dangerous toy.
Caution Vibration emissions can cause a health hazard if the device is used
for an extended period of time or if it is not properly handled and
maintained.
Caution Keep a sufficient distance from heat sources.
6
cordless drill driver PSCS 11-20V
EN
Note If you store or transport the device improperly, the device may be
damaged. Note the information regarding transport and storage of the device.
Note Only change the rotational direction when the device is at a standstill!
Otherwise the device might be damaged.
Note Set the torque and rotational direction according to the operating mode.
A wrong selection may damage the device.
Behaviour in the event of an emergency / emergency stop function
Emergency stop:
Removing the battery results in the function of the device stopping
immediately. Leave the battery out in order to secure the device against
accidental switch-on.
Behaviour in the event of an emergency: 1. Switch the device off. 2. In the
event of an emergency, remove the battery from the
device: Hold the release button of the battery and pull the battery off the
device as described in chapter “Removing the battery”. 3. Do not insert the
battery if the device is defective.
EN
cordless drill driver PSCS 11-20V
7
Information about the device
Device description
The cordless drill driver PSCS 11-20V has two speed levels: while the first
speed level is suitable for screwing, drilling can be performed using the
second speed level.
The integrated torque selection, including one drilling setting, allows you to
use the optimum power for every application, adapted to the material and screw
size.
The keyless drill chuck with automatic spindle lock further enables an easy
and tool-free exchange of the insertion tools.
The integrated LED work lamp offers an improved illumination of the workpiece
or working surface,
and the optionally mountable belt clip facilitates transport and provides
faster access to the device.
The battery comes with its own battery level indication. As a result you can
check the current charging status without having to connect it to the device.
Device depiction
12
3
4 5
6 17
7 16
No. Designation 1 Keyless drill chuck 2 Torque selection 3 Gear selection (2
speed levels) 4 Clockwise / counter-clockwise rotation, lock 5 On/off switch
(speed regulation) 6 Handle 7 Attachment for belt clip 8 Battery 9 Quick
charger 10 Red battery LED (battery charging) 11 Bits 12 Belt clip 13 Green
battery LED (quick charger ready for operation) 14 3-stage battery level
indication 15 Unlocking button 16 Battery holder 17 LED work lamp
Scope of delivery · 1 x Cordless drill driver · 1 x Rechargeable battery · 2 x
Bits (50 mm) · 1 x Quick charger · 1 x Belt clip · 1 x Transport case · 1 x
Manual
15
8
14
9 13
10
12
11
8
cordless drill driver PSCS 11-20V
EN
Technical data
Parameter
Value
Model
PSCS 11-20V
Nominal voltage
20 V
Idle speed 1. Speed level 2. Speed level
0 400 rpm 0 1550 rpm
Torque settings
25 +1
Chucking range
max. 13 mm
Max. drilling diameter Wood Metal
30 mm 13 mm
Max. torque
35 Nm
Weight
1.7 kg
Battery
Multiflex 20–2.0 DC
Type
Li-ion
Nominal voltage
20 V
Capacity
2 Ah
Quick charger
Multiflex 20–2.0 AC
Input
Nominal voltage
230 240 V / 50 Hz
Power input
65 W
Output
Nominal voltage
21.5 V
Charging current
2.4 A
Fusing
3.15 A (slow-blowing)
Charging time
1 h
Protection class
II /
Sound values according to EN 62841
Sound pressure level
72.20 dB (A)
Sound power level
83.20 dB (A)
Uncertainty K
3 dB (A)
Vibration information according to EN 62841
Vibration emission value for drilling in metal ah
Uncertainty K
1.643 m/s2 1.5 m/s2
Information on noise and vibration: · The specified total vibration and noise
emission values
were measured by means of a test procedure standardized in EN 62841 and can be
consulted for the comparison of one power tool with another.
· The specified total vibration and noise emission values can also be used for
preliminary load assessment.
Caution
Vibration emissions can cause a health hazard if the device is used for an
extended period of time or if it is not properly handled and maintained. · The
actual vibration and noise emission may differ from the stated values during
operation of the power tool. This depends on how the power tool is used and
especially on the type of workpiece being processed. Try to keep the vibration
load to a minimum. Exemplary measures for reducing the vibration load include
wearing gloves during operation of the tool and the limitation of working
hours. All parts of an operating cycle must be considered for this (e.g. times
at which the power tool is switched off and times when it is switched on but
runs without load).
EN
cordless drill driver PSCS 11-20V
9
Transport and storage
Note If you store or transport the device improperly, the device may be
damaged. Note the information regarding transport and storage of the device.
Transport
For transporting the device, use the transport case included in the scope of
delivery in order to protect the device from external influences.
Before transporting the device, observe the following: · Switch off the device
by setting the switch for clockwise/
counter-clockwise rotation to centre position (lock).
· Hold onto the mains plug while pulling the power cable of the charger out of
the mains socket.
· Allow the device to cool down.
· Remove the battery from the device.
· Remove the tool from the tool holder.
The supplied Li-ion batteries are subjects to the requirements of dangerous
goods legislation.
Observe the following when transporting or shipping Li-ion batteries: · The
user may transport the batteries by road without any
additional requirements.
· If transport is carried out by third parties (e.g. air transport or
forwarding company), special requirements as to packaging and labelling must
be observed. This includes consulting a dangerous goods specialist when
preparing the package.
Only ship batteries if their housing is undamaged. Mask open terminals
with tape and pack the battery in
a way that it cannot move inside the packaging. Please also observe any
other national regulations.
Storage
Before storing the device, observe the following: · Switch off the device by
setting the switch for clockwise/
counter-clockwise rotation to centre position (lock).
· Hold onto the mains plug while pulling the power cable of the charger out of
the mains socket.
· Allow the device to cool down.
· Remove the battery from the device.
· Remove the tool from the tool holder.
· Clean the device as described in the Maintenance chapter.
· For storing the device, use the transport case included in the scope of
delivery in order to protect the device from external influences.
· Do not store Li-ion batteries which are completely discharged. Storing
discharged batteries can lead to a deep discharge and thus damage the battery.
When the device is not being used, observe the following storage conditions: ·
Dry and protected from frost and heat
· Ambient temperature below 45 °C
· Protected from dust and direct sunlight inside the transport case
Start-up
Unpacking the device · Take the transport case out of the packaging.
Warning of electrical voltage Electric shock from insufficient insulation.
Check the device for damages and proper functioning before each use. If you
notice damages, no longer use the device. Do not use the device when the
device or your hands are damp or wet! · Check the contents of the transport
case for completeness and look for damages.
Warning Risk of suffocation! Do not leave the packaging lying around. Children
may use it as a dangerous toy. · Dispose of the packaging material according
to the national regulations.
10
cordless drill driver PSCS 11-20V
EN
Charging the battery
Note
The battery can be damaged in case of improper charging. Remove the charger’s
mains plug before inserting or removing the battery. Never charge the battery
at ambient temperatures below 10 °C or above 40 °C.
The battery is partially charged upon delivery to avoid damage to the battery
caused by a deep discharge.
Prior to initial start-up and when the battery is low (only the red LED in the
battery level indication (14) is illuminated), the battery should be charged.
To do so, please proceed as follows: 1. Slide the battery (8) onto the quick
charger (9) upside
down until it locks in place.
Inserting the battery 1. Set the switch for clockwise / counter-clockwise
rotation (4) to centre position (lock). 2. Slide the battery (8) onto the
device until it locks in place.
4
8 8
1 h
9 13
Removing the battery
1. Set the switch for clockwise / counter-clockwise rotation (4) to centre
position (lock).
2. Detach the battery (8) from the device by pressing and holding the
unlocking button (15, I.) and pulling the battery off the device (II.).
10
2. Insert the mains plug of the quick charger (9) into a properly fused mains
socket. ð The red battery LED (10) lights up. ð Charging requires approx. one
hour.
3. Wait until the red battery LED (10) goes off and the green battery LED
(13) lights up. ð The battery (8) is fully charged.
4. Hold onto the mains plug while pulling the power cable of the quick
charger (9) out of the mains socket. ð The battery (8) and the quick charger
(9) may have become warm during charging. Allow the battery (8) to cool down
to room temperature.
5. Take the battery (8) out of the quick charger (9) by pressing and holding
the release button (15) and pulling the battery (8) off the quick charger (9).
4
II. I.
8 15
3. If required, charge the battery (8) as described in the section Charging
the battery.
EN
cordless drill driver PSCS 11-20V
11
Checking the battery charging status
The battery comes with an integrated battery level indication.
The battery status is displayed as follows by the three LEDs of the battery
level indication (14):
LED colour
Meaning
Green Orange Red
maximum charge / power
Orange Red
medium charge / power
Red
weak charge Recharge the
battery.
1. Press on the battery icon (18) on the battery (8). ð You can read the battery status from the battery level indication (14).
4. Insert the appropriate (drill) bit into the drill chuck.
14
18
Tool change
The device is equipped with a fully automatic spindle lock. When the tool is
at a standstill, the motor’s drive train is locked so that the keyless drill
chuck can be opened. Please proceed as follows to remove or insert tools: 1.
Set the switch for clockwise / counter-clockwise
rotation (4) to centre position (lock). 2. Turn the keyless drill chuck (1)
counter-clockwise to open
it.
5. Tighten the keyless drill chuck (1) by turning clockwise.
3. If necessary, take the (drill) bit out of the drill chuck.
12
cordless drill driver PSCS 11-20V
EN
Torque selection / drilling setting
Using the torque selection, you can choose the desired, optimal torque
setting.
Info
When unscrewing, note the setting of the rotational direction! On the
clockwise / counter-clockwise rotation direction indicator (4) you can see in
which direction the screws will be screwed.
Do not use the drilling setting
for screwing!
Two-speed gear
Note
Only use the gear selection when the device is at a standstill! Otherwise the
device might be damaged. 1. Slide the gear selection (3) to the desired
position.
· Select a low torque for smooth-running screws or soft materials.
· Select a high torque for tight screws and hard materials as well as for
unscrewing.
· For drilling, select the drilling setting indicated by the
symbol .
ð Speed level 1: Speed of up to 400 rpm, suitable for all screwing
applications.
ð Speed level 2: Speed of up to 1550 rpm, suitable for drilling.
EN
cordless drill driver PSCS 11-20V
13
Mounting the belt clip Optionally, you can mount the belt clip included in the
scope of delivery to the device. 1. Set the switch for clockwise / counter-
clockwise
rotation (4) to centre position (lock). 2. Loosen the screw at the attachment
(7) for the belt clip. 3. Fasten the belt clip (12) to the belt clip
attachment (7) by
means of the screw.
4
7 12
Operation
Tips and notes on handling the cordless drill driver General information: ·
Check the tool in the keyless drill chuck for correct fit
before every application. It must be firmly locked and centred in the drill
chuck. · Screw bits are marked with their size and shape. If you are unsure,
check whether the bit can be firmly tightened in the keyless drill chuck
without clearance. · The centre position of the clockwise/counter-clockwise
rotation switch (lock) is suited for work breaks or (drill) bit exchange.
Screwing: · In case of soft wood, screws can be screwed in without pre-
drilling. · In case of hard wood or large screws, it is recommended to use a
drill for pre-drilling. · When using countersunk screws, the drill hole should
be countersunk beforehand. · Especially smaller screws and bits may be damaged
when selecting an excessive torque and / or speed at the tool.
Drilling in general: · Take short breaks regularly during drilling. When doing
so,
take the drill bit out of the drill hole so that the drill bit can cool down.
· Secure the workpiece in a tensioning device or vice.
· Select the speed depending on the material characteristics and the size of
the drill bit:
High speed for small drilling diameter or soft material Low speed for
large drilling diameter or hard material · Use a suitable aid to mark the
intended location of the drill hole.
· Select a low speed for spudding.
Drilling in metal: · Use suitable metal drill bits (e.g. drill bits made of
high-speed steel (HSS)).
· For larger drilling diameters, use a smaller drill bit for pre-drilling.
· To achieve ideal results, the drill bit should be cooled with a suitable
lubricant.
· Metal drill bits may also be used for drilling in plastic.
Drilling in wood: · Use drill bits suitable for wood.
· Place a block of wood under the workpiece or drill in from both sides so
that the wood cannot break off when it is being drilled through.
· Use a wood drill bit with centring tip. For deep drill holes, use an auger
bit; for large drilling diameters, use a Forstner bit.
14
cordless drill driver PSCS 11-20V
EN
Selecting the rotational direction
Note Only change the rotational direction when the device is at a standstill!
Otherwise the device might be damaged.
The motor’s rotational direction can be changed by means of the switch for
clockwise / counter-clockwise rotation (4). 1. Press the switch for clockwise
/ counter-clockwise
rotation (4) in all the way on that side towards which the motor shall rotate.
I.
II.
Switching the device on and off
The device has an infinitely variable speed control. The more firmly you push
the on/off switch (5), the higher is the speed. 1. Check whether the tool
clamped in and the torque setting
selected are suitable for the intended application. 2. Check whether the
workpiece is secured and the worktop
prepared correspondingly. 3. Press and hold the on/off switch (5) during
screwing or
drilling. ð The device operates with the previously selected
settings. ð The LED work lamp (17) is illuminated.
4
I. Screwing in
II. Unscrewing
2. Carry out a short test run to see whether the rotational direction matches
the intended application. A wrong rotational direction may damage the tool and
/ or workpiece.
3. If required, set the switch for clockwise / counterclockwise rotation (4)
to centre position (lock) to block the on/off switch (5).
5
17
4. Let go of the on/off switch (5) to stop the device. ð The LED work lamp
(17) turns off. Info The motor has an integrated brake that quickly stops the
motor once you let go of the on/off switch (5).
Shutdown 1. Set the switch for clockwise / counter-clockwise
rotation (4) to centre position (lock). 2. If required, allow the device to
cool down. 3. Remove the battery from the device (see Start-up chapter). 4.
Remove the tool from the device (see Start-up chapter). 5. Clean the device
according to the Maintenance chapter. 6. Store the device according to the
Storage chapter.
EN
cordless drill driver PSCS 11-20V
15
Available accessories
Warning Only use accessories and additional equipment specified in the
instructions. Using insertion tools or accessories other than those specified
in the instructions may cause a risk of injury.
Accessories Multiflex 20V 2.0 Ah spare battery Screw bit set, 32-piece Wood drill bit set, 15-piece Metal drill bit set HSS, 15-piece
Article number 6.200.000.303 6.200.001.001 6.200.001.101 6.200.001.131
Errors and faults
The device has been checked for proper functioning several times during
production. If malfunctions occur nonetheless, check the device according to
the following list.
Troubleshooting tasks which require the housing to be opened must only be
carried out by an authorized specialist electrical company or by Trotec.
Light smoke or odour is emitted during the first use: · This is not a fault.
These phenomena disappear after a
brief runtime.
The battery does not charge: · Check whether the battery is correctly
connected to the
quick charger.
Slide the battery into the quick charger in a way that the battery terminals
engage in the quick charger. The battery must lock in place in the quick
charger.
· Check the power connection.
· Check the power cable and mains plug for damages.
· Check the fuse (home).
· Check the quick charger for damages. Should the quick charger be damaged,
stop using it. Contact the Trotec customer service.
· Check the battery terminals for dirt. Remove any dirt.
· The battery might be defective and have to be replaced. Only use batteries
of the same type.
The device does not start: · The battery power might be too low. Recharge the
battery.
· Check whether the battery is correctly connected to the device.
Slide the battery onto the device in a way that the battery terminals engage.
The battery must lock in place in the device.
· Check the position of the clockwise/counter-clockwise rotation switch. The
switch must be pressed in all the way. If the clockwise/counter-clockwise
rotation switch is in centre position (lock), the on/off switch is blocked.
· Check the battery terminals for dirt. Remove any dirt.
Info
Wait for at least 10 minutes before switching the device back on.
The drill bit does not penetrate / hardly penetrates the
material: · Check whether the correct torque setting is selected. The
drilling setting
should be selected.
· If necessary, increase the speed by switching to a high speed level (2nd speed level).
· Check whether the correct drill bit is selected.
· Check whether the device is set to counter-clockwise rotation. For drilling, it is necessary to switch over to clockwise rotation.
· Check whether the characteristics of the material require the use of a hammer drill or impact drill.
The on/off switch cannot be pressed: · Check whether the clockwise/counter-
clockwise rotation
switch is in centre position (lock). Set the desired rotational direction to
unlock the tool.
Note Wait for at least 3 minutes after maintenance and repair work. Only then
switch the device back on.
The device still does not operate correctly after these checks:
Please contact the customer service. If necessary, bring the device to an
authorised specialist electrical company or to Trotec for repair.
16
cordless drill driver PSCS 11-20V
EN
Maintenance
Disposal
Activities required before starting maintenance
Warning of electrical voltage Do not touch the mains plug or the battery with
wet or damp hands. · Switch the device off.
· Allow the device to cool down completely.
· Remove the battery from the device.
Warning of electrical voltage Maintenance tasks which require the housing to
be opened must only be carried out by authorised specialist companies or by
Trotec.
Notes on maintenance Inside the device, there are no parts that need to be
maintained or lubricated by the user.
Safety signs on the battery and the charger Check the safety signs attached to
the battery and the charger at regular intervals. Replace illegible safety
signs!
Cleaning The device should be cleaned before and after each use.
Note The device does not have to be lubricated after cleaning.
Warning of electrical voltage There is a risk of a short-circuit due to
liquids penetrating the housing! Do not immerse the device and the accessories
in water. Make sure that no water or other liquids can enter the housing. ·
Clean the device with a soft, damp and lint-free cloth. Make sure that no
moisture enters the housing. Protect electrical components from moisture. Do
not use any aggressive cleaning agents such as cleaning sprays, solvents,
alcohol-based or abrasive cleaners to dampen the cloth.
· Dry the device with a soft, lint-free cloth.
· Dry the bits with a soft, lint-free cloth.
· Remove any drilling dust and, if applicable, wood chips from the keyless
drill chuck.
· Keep the connecting terminals on the device and charger clean.
· Keep the ventilation openings free from dust deposits to prevent overheating
of the motor.
The icon with the crossed-out waste bin on waste electrical or electronic
equipment stipulates that this equipment must not be disposed of with the
household waste at the end of its life. You will find collection points for
free return of waste electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local administration. You
can also find out about other return options that apply for many EU countries
on the website https://hub.trotec.com/?id=45090. Otherwise, please contact an
official recycling centre for electronic and electrical equipment authorised
for your country.
The separate collection of waste electrical and electronic equipment aims to
enable the re-use, recycling and other forms of recovery of waste equipment as
well as to prevent negative effects for the environment and human health
caused by the disposal of hazardous substances potentially contained in the
equipment.
Li-Ion
In the European Union, batteries and accumulators must not be treated as
domestic waste, but must be disposed of professionally in accordance with
Directive 2006/66/EC of the European Parliament and of the Council of 6
September 2006 on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.
EN
cordless drill driver PSCS 11-20V
17
Declaration of conformity
Declaration of conformity in accordance with the EC Machinery Directive
2006/42/EC, Annex II, Part 1, Section A
We Trotec GmbH declare in sole responsibility that the product designated
below was developed, constructed and produced in compliance with the
requirements of the EC Machinery Directive in the version 2006/42/EC.
Product model / Product: PSCS 11-20V
Product type:
cordless drill driver
Year of manufacture as of: 2021
Relevant EU directives: · 2011/65/EU: 01/07/ 2011
· 2012/19/EU: 24/07/2012 · 2014/30/EU: 29/03/2014 · 2015/863/EU: 31/03/2015
Applied harmonised standards: · EN 55014-1:2017
· EN 60745-2-2:2010
· EN 62841-1:2015
· EN 62841-2-1:2018
Applied national standards and technical specifications: · EN 55014-2:2015
Manufacturer and name of the authorised representative of the technical
documentation:
Trotec GmbH
Grebbener Straße 7, D-52525 Heinsberg
Phone: +49 2452 962-400 E-mail: info@trotec.de
Place and date of issue: Heinsberg, 20.07.2021
Detlef von der Lieck, Managing Director
18
cordless drill driver PSCS 11-20V
EN
Trotec GmbH
Grebbener Str. 7 D-52525 Heinsberg
+49 2452 962-400 +49 2452 962-200
info@trotec.com www.trotec.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>