SHIDU H1 PA Speaker Instruction Manual

SHIDU H1 PA Speaker

Welcome to using SHIDU digital speaker. H1 Plus is a multifunctional portable speaker with Bluetooth and voice amplifier functions, also can play music through a TF card and USB flash driver. Please enjoy it after reading the user manual.

Main features

1. 30W output, 5.25-inch full-range speaker;
2. Support Bluetooth 5.0;
3. Rechargeable 3.7V 4400mAh A-grade lithium battery;
4. Support audio input and audio output;
5. Support ECHO effect, FM radio;
6. Support TF card, USB flash drive playback;
7. UHF wireless microphone.

Technical Parameters

STRUCTURE INFORMATION

1. Power on/off the Long press it for 3 seconds and the display screen lights up means power on. Long press it again for 3 seconds, and the display screen light out means power off.
2. Recording
3. Mode selection

• Short press “M” to select Bluetooth mode / USB flash drive mode /TF card mode / FM mode/UHF mode.
• In music play mode, long press “M” for 3 seconds to switch to a single song repeat. The screen will display “ONE”, long-press the “M” key again to switch back to all repeat and the screen will display “ALL”.

1. Previous: Short press to select the previous audio file.
2. Play/Pause:
3. In audio playing mode, short press it to pause; short press it again to play:
4. In any mode, double press the” ” button to close the voice prompt of the speaker, and double press “ ” the button again to turn on the voice prompt of the speaker.
5. Next: Short press to select the next audio file.
6. Music volume: Rotate the knob clockwise to “ + ” to continuously increase the music volume; rotate the knob to”-” to decrease the music volume.
7. MIC volume: Rotate the knob clockwise to “ + ” to continuously increase the MIC volume; rotate the knob to “ – ” to decrease the MIC volume.
8. ECHO
9. MIC 1 input
10. MIC 2 input
11. Audio input
12. Audio output
13. USB port: Support USB flash drive play, with a voice prompt “USB flash driver playing’. Maximum support 32GB USB flash drive.
14. TF card slot: Support TF card play, with a voice prompt TF card playing'”. Maximum support 32GB TF card.
15. DC 5V: Please use the DC 5V 2A power adapter to charge the speaker.

Playing from TF card/USB flash drive

The speaker will automatically play the music file after inserting the TF card/USB flash drive, and the previous song and the next song can be selected by short pressing the   button.

Recording Function

To record

1. Connected the wireless or wired microphone, then insert the storage (USB flash drive or TF card).
2. Long press “REC” key to start recording, and the display will indicate the time. Short press the “REC” key again to stop recording, it would save the audio file and play the recording.

To play a recording

Insert a USB flash drive or TF card with recording files. Short press the “REC” key to play back recordings. It will play the last recording by default. Short press to select the previous and next recordings.

FM Function

Switch on the speaker, short press “M” to choose the FM mode with the screen showing radio frequency; Long press Ito enters into automatic channels searching after searched successfully, the device will save the channel automatically. Please press to choose the saved channels.

Bluetooth Function

Please pair with your Bluetooth device as follows:

Step 1: Turn on the amplifier and short press the “M” key to switch to Bluetooth mode. A voice will prompt “Bluetooth is waiting for connection”. The screen will display “blUE” and keep 1ashing.

Step 2: From your mobile setting, turn on the Bluetooth function. Then search for “H1 PLUS” and connect. Bluetooth pairing is completed with a voice prompt “Bluetooth is connected’. And the bLUE “display will stop 1lashin9. When playing music, please keep the amplifier close to the Bluetooth-enable device to maintain a stable connection.

Charging the device

• When working, the battery icon on the screen flash continuously, indicating that the battery is low, please charge it in time. Please use the standard adapter to charge. Please unplug the adapter timely after fully charged, the charging time is normally 5-6 hours.
• In order to achieve the best effect when using the speaker for the first time, it is recommended to be fully charged before use.
• Please use the standard 5V 2A charger to charge the device.

Wireless Microphone Operation

Switch ON/ OFF

Long press “ ” on the wireless microphone to switch it on. The screen display will show a default frequency point. Long press “ ” on the power-on state will turn off the microphone and the screen goes out.

Notes: It will enter into screen protection mode after 10 seconds. Short press the” ” button and the screen will blinking.

Pair the UHF Wireless MIC Manually (This operation is used when the MIC is no sound)

a.Switch on the speaker, select UHF mode, and long press “M” to enter into UHF wireless pairing status with “UHF” flashing on the screen.
b.Switch on the UHF wireless MIC by long press . The screen will display the current frequency point. Quick press “ ” button 3 times and the current frequency point will flash, which means wireless MIC has paired with the speaker successfully.

Battery Indication of UHF Wireless MIC

In working status, it has sufficient battery power with “ ” indication shown on screen; it’s a low battery with indication showed on screen, and please change the battery timely.

Note: Please open the battery cover properly and put it on the batteries. (Please note the positive & negative anode.)

Remote function:(Not included)

1. Normally, the remote control should be in front of the receiving window and within the scope of 6M & 30°.
2. Please point the remote control toward the receiving window and avoid the obstacle.
3. Please avoid the strong light.
4. Please don’t use old & new batteries at the same time.

Note: Please refer to the real product.

Trouble Shooting

Switch on the speaker but no sound

1. No audio input: Please use other better audio files;
2. Haven’t turned on the volume: Please adjust the volume properly.
3. No power of speaker: Charge the speaker to see whether Screen has been lightened.

With sound distortion

1. The volume is too high: Please turn down the volume properly
2. The speaker is broken: Please contact us for maintenance.

No sound with MP3 playing

1. The audios’ format in USB flash drive or TF card is Wrong: Please turn the format to MP3;
2. Chaotic procedure with the wrong operation: Please restart the speaker,
3. Have not inserted the USB flash drive /TF card properly:
4. Please insert the USB/TF card properly.

Can only work several minutes after charged

1. The battery Is broken: Please change a new same battery
2. The connecting cable of the battery is loosened or disconnected: Please contact us Tor maintenance
3. Hasn’t full charged the speaker: Please full charge it before using.

SHIDU Guarantee

• 100% SHIDU Guaranteed Product Satisfaction.
• We promise a 1-year warranty.
• If you have any questions, please feel free to contact us, we will try our best to provide you with the best service.
• www.10shidu.com
• Email: service@10shidu.com

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following Two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>