amibot Spirit Robot Vacuum User Manual

June 10, 2024
amibot

Spirit Robot Vacuum

amibot-Spirit-Robot-Vacuum-product-image

Product Overview

The AMIBOT Spirit Premium robot vacuum comes with a 2-in-1 compartment, 2 microfiber cleaning pads, 2 HEPA filters, 4 side brushes, a cleaning tool, and a remote control. The Spirit Premium
Station version includes 2 dust bags and an auto-empty station. The robot vacuum has a power button, home base button, and a laser module on the top. The bumper and bin are located on the side, and the bottom has gap sensors, power sensors, side brushes, a battery cover, side wheels, a castor, central brush cover, central brush, and a tank.

Product Usage Instructions

  1. Place the home base in an open space with access to a power outlet.
  2. Charge the robot vacuum by pressing the power button until it turns on and then pressing the home base button to start charging.
  3.  Attach the side brushes to the robot vacuum.
  4. Fill the tank with water and attach a cleaning pad to the 2-in-1 compartment.
  5. Select the cleaning mode on the remote control or robot vacuum.
  6. Press the OK button to start cleaning.
  7. Monitor the indicator lights and sounds for notifications such as low battery or full bin.
  8. Empty the bin and replace the HEPA filter as needed.
  9. Clean the side brushes and central brush cover regularly using the cleaning tool.
  10. For the Spirit Premium Station version, replace the dust bag in the auto-empty station when full.

Please refer to the user manual for troubleshooting tips and warranty information. Contact AMIBOT customer service for any additional questions or concerns.

Recommendations

  • AMIBOT Spirit Premium works with the AMIBOT HOME mobile app (available for Android and iOS). All of its functions can be accessed from the app.
  • The remote control supplied only offers the basic functions of a robot vacuum cleaner.
  • AMIBOT Spirit Premium is designed to be used inside.
  • AMIBOT Spirit Premium is designed for a maximum surface area of 220 m².
  • AMIBOT Spirit Premium is designed for routine floor cleaning. It is not intended to replace heavy-duty cleaning.
  • AMIBOT Spirit Premium needs a headway of at least 11 cm so that it can go under furniture.
  • AMIBOT Spirit Premium cannot go over thresholds over 1  cm thick, otherwise it automatically stops or reverses.
  • AMIBOT Spirit Premium is not designed to be used on long-pile carpets, which could cause the robot to freeze or reverse.
  • AMIBOT Spirit Premium must be used on flat surfaces.
  • If the robot could come across a gap while cleaning, please secure the area and check that the gap sensors are clean.
  • AMIBOT Spirit Premium is not designed to vacuum water or other liquid products.
  • Do not use the appliance on damp floors.
  • Please switch the appliance off before handling it (manually moving it, maintenance, storing it away).
  • The remote control requires 2 x LR03-type batteries (AAA). They are not supplied with the robot.
  • The laser module located on the top of the robot is fragile. Never press or pull on it as you risk damaging it.

Product overview

Product contentsamibot-Spirit-Robot-Vacuum-01

  1. AMIBOT Spirit Premium robot
  2. 2-in-1 compartment
  3. 2 x microfibre cleaning pads and base
  4. 2 x HEPA filters
  5. Home base and power adapter (Spirit Premium version)
  6. 4 x side brushes
  7. Cleaning tool
  8. Remote control (batteries not included)
  9. User manual
  10. 2 x dust bags (Spirit Premium Station version)
  11. Auto-empty station (Spirit Premium Station version)
Product diagram

Robot top viewamibot-Spirit-Robot-Vacuum-02

  1. Power button
  2. Home base button
  3. Laser module
  4. Bumper
  5. Bin

Robot side view

  1. Wall sensor

amibot-Spirit-Robot-Vacuum-03

Robot bottom viewamibot-Spirit-Robot-Vacuum-04

  1. Gap sensors
  2. Power sensors
  3. Side brushes
  4. Battery cover
  5. Side wheels
  6. Castor
  7. Central brush cover
  8. Central brush
  9. Tank

2-in-1 compartment and cleaning pad baseamibot-Spirit-Robot-
Vacuum-05

  1. Filter housing
  2. Prefilter
  3. HEPA filter
  4. Refill cap
  5. Dustbin release button

Product overview

  1. amibot-Spirit-Robot-Vacuum-06 Drip nozzles
  2. Cleaning pad Velcros

Home base (Spirit Premium version)

  1. Power indicator light
  2. Charging contacts
  3. Power terminal
  4. Integrated cable tidy
  5. Recess for cable
  6. Coveramibot-Spirit-Robot-Vacuum-07

Auto-empty station (Spirit Premium Station version)

  1. Power indicator light
  2. Infrared emitter
  3. Auto-empty inlet
  4. Auto-empty station pins
  5. Power cord port

amibot-Spirit-Robot-Vacuum-08

  1. Cover
  2. Dust bag connector
  3. Dust bag
  4. Dust evacuation tube
  5. Fan cover amibot-Spirit-Robot-Vacuum-08

Remote control amibot-Spirit-Robot-Vacuum-10

  1. AUTO mode
  2. Directional arrow buttons
  3. MAX mode
  4. Mute button
  5. Light button
  6. Home base button
  7. Start/pause button
  8. Auto-empty station button (Spirit Premium Station ver-sion)
  9. Water flow button
  10. AREA TO CLEAN mode button

Operation

Mobile app
The AMIBOT HOME app offers access to all the functions listed in this manual.

Downloading
Download the AMIBOT HOME mobile app available for Android and iOS, then create an account. To do this, follow the steps in the app directly.

Pairing a device

IMPORTANT: You must make sure that your Wi-Fi router is connected to the 2.4 GHz band and not the 5 GHz band so that you can pair your robot with the AMIBOT HOME app. Please check your router settings or contact your Internet provider’s customer service department.

Add the robot using the “+” button on the app’s home page.

To activate the robot’s pairing mode, hold the power button and home base button at the same time for around 5 seconds. Then follow the steps indicated on your smartphone.

Once the robot is correctly paired to your smartphone, go to its settings and control it remotely.

Sharing the robot
You can control the robot on several smartphones at a time. To do this, the robot must be shared.
Go to the robot’s page and click on the Pencil icon at the top right of the screen. Select Share Devices then Add Sharing. Enter the email address of the user you want to share the robot with. The user must have already downloaded the AMIBOT HOME app and created their account.

NOTE:

  • You need to have one AMIBOT Home user account per smartphone.
  • To remove a user from a robot share, go to the device’s sharing settings, select the user you would like to remove and swipe to the left. Then click on Delete. The user can also remove the robot directly via these same settings by clicking on Remove robot sharing.

Operating the robot
The robot has a laser and smart gyroscope system. It uses a precise route and marks out the area it will clean in squares.

Thanks to the laser and AMIBOT HOME mobile app, you can follow the robot’s cleaning route in real time via the map.

NOTE: For the purposes of continuous improvement, updates to the AMIBOT HOME mobile app may lead to some settings being changed.

Charging
Assembling the home base (Spirit Premium version)amibot-Spirit-Robot-
Vacuum-12To plug in the home base, open the cover under the robot and plug in the power cable. Wind the cable around integrated cable tidy and thread through the recess. Then put the cover back on again. Place the home base on a level surface next to a wall, at a right angle to the floor. Keep a distance of at least 1.5 m in front of the base and 0.5 m at either side.

NOTE: When your AMIBOT Spirit Premium robot is on its home base, make sure that your robot is switched on and the home base power light is on.

Assembling the auto-empty station (Spirit Premium Station version) amibot-
Spirit-Robot-Vacuum-13Plug in the auto-empty station using the power cable. Place the home base on a level surface 6 cm from the wall. Keep a distance of at least 1.5 m in front of the base and 0.5 m at either side. Place the dust bag in its compartment in the auto-empty station.

Once cleaning is complete, the robot goes to auto-empty at its auto-empty station and then charges from the front.

NOTE:

  • When your AMIBOT Spirit Premium robot is on its auto-empty station, make sure that your robot is switched on and the station’s power light is on.
  • The auto-empty station must be placed on a smooth, flat surface, otherwise the robot may not empty effectively.

Switching on the robotamibot-Spirit-Robot-
Vacuum-14 Press the power button for 3 seconds. The robot is ready to be charged.

Charging the robot  The battery can only be charged on the home base.

NOTE:

  • The robot must be switched on while it is being charged.
  • Do not place a mirror or other highly reflective object within a distance of at least 15 cm from the home base.
  • Do not place the home base in direct sunlight.
  • When the robot’s battery is completely flat, the power button’s indicator light flashes red. While charging, the indicator light flashes blue. Once fully charged, the indicator light is steady blue.
  • If the battery is weak while the robot is cleaning, it automatically returns to its home base. The home base must therefore be switched on.
  • If the robot is not used for a long period of time, you are recommended to fully charge the battery, switch off the robot and store it in a cool, dry place.

Vacuum modeamibot-Spirit-Robot-Vacuum-16To use the vacuum mode, attach the dustbin to back of the appliance.

Mopping mode
Attaching the cleaning pad amibot-Spirit-Robot-
Vacuum-17

Attach the cleaning pad (Figure 1) to the base using the Velcros on the underneath (Figure 2).

Preparing and inserting the 2-in-1 compartment

amibot-Spirit-Robot-Vacuum-18 Open the water tank’s refill nozzle (Figure 1) and carefully pour in clean water with some floor cleaner.

NOTE:

  • For optimum performance, the water tank must have at least 50 ml of liquid.
  • For optimum cleaning, check the dilution ratio indicated on the detergent bottle.
  • Only use floor cleaner products. Prolonged use of any other product, such as white vinegar, essential oils, black soap or bleach, could damage the water tank.
  • A cleaning pad must be attached to the back of the robot whenever there is water in the water tank.

Inserting the 2-in-1 compartment

Thanks to the 2-in-1 compartment, the robot can vacuum and mop hard floors at the same time. Clip it on the cleaning pad attachment to the back of the robot, which automatically detects the tank. The robot is ready to start its mopping cycle.

When the robot is turned on for its cleaning cycle, the automatic pump in the water tank is activated to clean hard floors.

NOTE:

  • You can regulate the water tank’s water flow intensity via the remote control (see page 10).
  • Do not use the water tank on rugs or carpets.
  • Empty the water tank and remove the cleaning pad attachment from the robot before charging it.

Tips: When using the mopping mode, remove the central brush from its compartment to prevent risk of oxidation. This will make cleaning the robot easier!

Auto-emptying of robot
After each cleaning in suction mode (only), the robot will automatically empty its dust tank on its station.
The automatic emptying is carried out via the flap located underneath the robot. It is therefore essential to remove the H2O mop holder.

amibot-Spirit-Robot-Vacuum-20The robot then moves backwards on its station in order to position the dust tank discharge valve on the station’s suction circuit inlet. Once in contact, the automatic emptying starts. The robot then positions itself on its station from the front, in order to recharge. The frequency of emptying can be adjusted in the robot settings, from the AMIBOT HOME application.

NOTES :

  • It is necessary to remove the H2O mop holder from the robot in order to perform an automatic emptying.

amibot-Spirit-Robot-Vacuum-21

Starting the robot
Attach the 2-in-1 compartment and switch the robot on. Wait a few seconds to let it start up, then press the power button on the robot or the AUTO button on the remote control.

The robot starts its cleaning cycle in AUTO mode.amibot-Spirit-Robot-
Vacuum-22

NOTE:

  • If the robot is in standby mode, press the power button on the robot once or the AUTO button on the remote control to come out of standby.
  • The robot’s cycle can be interrupted and it can be manually controlled using the remote control.

Daily
Scheduling can only be performed via the AMIBOT HOME mobile app. Set your preferred daily cleaning times via the mobile app.

Cleaning modes
The robot has five cleaning modes. These cleaning modes can be selected via the remote control or the AMIBOT HOME mobile app. AUTO and AREA TO CLEAN mode can also be selected via the robot.

AUTO mode

amibot-Spirit-Robot-Vacuum-23 Press the power button on the robot or the AUTO button on the remote control. The robot uses its laser to scan the room to optimize its movements. It divides the room into areas in a zig-zag fashion to vacuum any debris and dust.
During an AUTO mode cleaning cycle, the robot may take a short break, so it can scan the room in real time and adapt its movements.

MAX mode

amibot-Spirit-Robot-Vacuum-24 The MAX mode is useful for floors that are extremely dusty. The robot has three vacuum levels. Press the MAX button on the remote control to increase or decrease the robot’s vacuum level.

NOTE: MAX mode is only accessible when the robot is in vacuum mode. It cannot be selected while the water tank is inserted. However, you can regulate the water flow intensity via the remote control.

SPOT mode

amibot-Spirit-Robot-Vacuum-25

This mode is the most effective when cleaning a particularly dirty area. With SPOT mode, the robot concentrates on a 1.5  m  x  1.5  m area. At the same time, it activates its MAX vacuum power to vacuum the dust from the floor more easily.

AREA TO CLEAN mode amibot-Spirit-Robot-Vacuum-26

The robot’s AREA TO CLEAN mode is available to clean a particular area. With this mode, the robot cleans an area of 1.8 m x 1.8 m. To use this mode, you need to place the robot in the area you want to clean and press the Home base button on the robot for 3 seconds or the AREA TO CLEAN button on the remote control.

HOME mode

amibot-Spirit-Robot-Vacuum-27

If you need to charge the robot at any time while in use, you can do so by pressing the Home base button. The robot will automatically go back to its home base once it has completed its cleaning cycle (the time it needs to search depends on the distance between the home base and if there are any obstacles along its route).

Pause
To pause the robot, press the power button on the robot or the OK button on the remote control.

Stopping the robot
When the robot finishes its cleaning cycle, it goes back to its home base. Press the power button on the robot or the OK button on the remote control to manually stop the robot.
With the Spirit Premium Station version, the robot automatically empties the dust in its compartment when it returns to the auto-empty station. The frequency with which the compartment empties automatically can be modified directly via the application.

Switching off the robot

Press the power button for 5 seconds.
The robot is switched off.

NOTE: never switch off the robot when it is on the home base.

Maintenance

Side brushesamibot-Spirit-Robot-Vacuum-29Unclip the side brushes by gently pulling them upwards and rinse them under clean water. Wait until they are completely dry before reusing them.
Check that the left brush is marked with an “L” and the right brush is marked with an “R”. The engraved letters on the side brushes and the robot are there to guide you.
NOTE: Side brushes must be replaced if you notice that their original shape has changed.

Side wheels and castor

Wipe the side wheels with a dry cloth to remove built up dust.

Pull firmly on the castor block to remove it. Then remove all the debris from inside the cavity using a soft cloth. Use a slotted screwdriver to remove the castor from its frame and wipe it clean. Remove the hair and other debris caught around the axle.

Compartments and filters
Dustbinamibot-Spirit-Robot-Vacuum-31

You should empty the dustbin every time the robot completes a cleaning cycle. Remove the dustbin by pressing the release button and empty it by opening the cover located on the underneath. Then check that there is no dirt obstructing the robot’s vacuum system.

Filters
Open the dustbin to access the filters and clean them.

  1. The HEPA filter cannot be cleaned, otherwise it would become damaged. To extend the filter’s life, gently shake it outside to remove any small dust particles that may have gathered. If the HEPA filter is damaged, it is advisable to replace it to keep up the efficiency of the robot’s filter.
  2. Carefully shake the pre filter and protection filter to remove any dust particles and rinse it with clean water. Let it completely dry before putting it back in the dustbin.

Water tankamibot-Spirit-Robot-Vacuum-32

Empty the water tank of any remaining water and rinse it with clean water. Regularly check that the tank’s two drip nozzles are not obstructed by debris or limescale. Clean them with a soft cloth. Wait until the water tank is completely dry before reusing it.

Gap and power sensors

amibot-Spirit-Robot-Vacuum-33 The gap and power sensors on the bottom of the robot and on the home base must be regularly cleaned with a soft cloth. Never let the sensors get wet.

Central brushamibot-Spirit-Robot-Vacuum-34

Unclip the central brush’s cover underneath the robot and remove the main brush. Clean the cavity using a soft cloth and remove dust and hair caught around the brush. Run under clean water for optimum cleaning. Wait until it is fully dry before putting it back.

Microfibre cleaning padsamibot-Spirit-Robot-
Vacuum-35
The microfibre cleaning pads are machine washable at 30° maximum or may be hand-washed with clean water and your usual washing detergent.
NOTE: Accessories need to be replaced in accordance with how frequently the robot is used and the amount and type of debris that it picks up.

Auto-empty station (Spirit Premium Station version)amibot-Spirit-Robot-
Vacuum-36

Empty the auto-empty station whenever it is necessary. Open the auto-empty station hood, then remove the dust bag by pulling on the tab (the bag is automatically sealed).
Insert a new dust bag.
To ensure an optimum use of the auto-empty station, regularly clean the charging sensors using a soft cloth. Also make sure the fan cover is kept clean.

Indicator lights and sounds

Robot status Instructions
Cycle starting Steady blue indicator lights
Cleaning process scanning Steady blue indicator lights
Charging Flashing blue indicator lights
Charging complete Steady blue indicator lights
**** Weak battery **** Red indicator lights
**** Home button Flashing blue indicator lights
**** Malfunctions (error) **** Red indicator lights
Robot not connected to the app Flashing pink indicator lights

NOTE: you can switch the indicator lights off by pressing the Light button on the remote control.

Robot status Instructions
Robot on “Power on”
Robot off “Power off”
Cycle starting “Cleaning start”
Cleaning cycled paused “Cleaning paused”
Cleaning cycle complete, return to the home base “Cleaning complete, back to

charge station”
Looking for home base| “Start recharge”
Charging| “Recharging”
Charging complete| “Recharging complete”
Dustbin inserted| “Dustbin in position”
Water tank inserted| “Water tank in position”
Weak battery| “Battery is low, please charge”
Connected| “Connected”

Troubleshooting

Please contact AMIBOT technical department in the following cases:

  • If the appliance has been dropped, damaged or come into contact with water.
  • If the power cable is damaged.
  • If the battery is defective.

Tables: Malfunctions and possible causes
To avoid breakdowns/malfunctioning, regularly check and clean the appliance accessories.

No. Sounds Cause Solution
01 “Oh dear! I cannot find the dust collector” The dustbin is not inserted
correctly. Check that the dustbin is inserted correctly.
02 “Please check if the radar on top has been covered or blocked” The laser
is frozen. Carefully clean the laser and place the robot on a flat surface.
03 “Please place me in a new location and try again” Position problem.

Place the robot on a flat surface and restart a cleaning cycle.
04| “Please scrub the cliff sensor, and restart me from a new location”| Problem with the gap sensors. The sensors are dirty.| Check the gap sensors and clean them using a soft cloth.
05| “Please scrub the front sensor, and restart me from a new location”|

The bumper’s sensors are dirty.

|

Clean the bumper’s sensors using a soft cloth.

06| “Please scrub the right-hand sensor, and restart me from a new location”| The wall sensor is dirty.|

Clean the wall sensor using a soft cloth and place the robot somewhere else.

07| “Please scrub the radar housing on top, and restart me from a new location”| The laser module is dirty.| Check the laser and clean it thoroughly. Be sure

to remove any dust that could prevent it from working, using a soft cloth.

08| “Please check if the bumper has been blocked in some way”| Problem with the bumper. The bumper is frozen.| Check the bumper and place the robot somewhere else.
09| “Master, please clean the dustbin and filters”| The dustbin is full or the filters are dirty.|

Empty the dustbin and clean the filters (see the Maintenance section).

10| “Dust container has been removed, please clean the container and filter”| Error n.09 means that the dustbin is not correctly inserted.| Insert the dustbin correctly.
11| “Please check if my wheels have become blocked somewhere”| Problem with the wheels and/or the castor.| Check the wheels and the castor and remove any elements likely to be blocking them.
12| “Please check if the main brush has become stuck”| Problem with main brush. The main brush is frozen.| Check the main brush and remove any dust or objects likely to be blocking it.
13| “Please check if the side brushes have become stuck”| Problem with side brushes. The side brushes are dirty or frozen.| Check the side brushes and remove any elements likely to be blocking them.
14| “What’s going on? Where is the docking station?”| The robot cannot find its home base.|

Check that the home base is correctly positioned and on. Manually place the robot on its home base.

15

| “Oh dear! Program error, please restart me”|

Error with the robot.

| Please turn off and restart the robot. If the problem persists, please contact the AMIBOT after-sales service.

16

|

“Low battery, please recharge”

| The robot battery is too weak.|

Charge the robot using its home base.

17| “To shut me down, please place me away from the docking station”| The robot will not shut down because it is on the home base.| Take the robot off the home base and press the power button for 5 seconds.
18| “Wi-Fi lost, please follow the App instruction for reconnection”| The robot is not connected to the AMIBOT HOME app.| Connect the robot to the smartphone via the AMIBOT HOME mobile app.
19| “Locating failed, map rebuilding”| Location problem.| The robot has lost its location. Please give the robot time to rescan its environment.
20|

“Collecting fan motor error”

| Problem with the fan.| Turn off the robot and then let it cool down. Turn it back on. If the problem persists, please contact the AMIBOT after-sales service.
21| The dust bag is not installed”| The dust bag is not inserted.|

Check that the dust bag is correctly inserted in the auto-empty station.

To avoid breakdowns/malfunctioning, regularly check and clean the appliance accessories.

No. Problem Cause Solution
01 The appliance does not switch on.
  1. The appliance is not switched on.
  2. The appliance has run out of battery.

|

  1. Switch the robot on.
  2. Charge the robot using its home base.

02| The robot does not charge any more.|

  1. The robot is not correctly positioned on the home base or it is not plugged in correctly.
  2. The robot is not switched on.

|

  1. Correctly reposition the robot and place its power sensors on the home base sensors.
  2. Switch the robot on.

03| The robot does not move correctly|

  1. The floor is wet.
  2. The dustbin is not attached correctly.
  3. The   central   brush is not inserted correctly.

|

  1. Dry the floor.
  2. Remove and reinsert the dustbin.
  3. Remove and reinsert the brush in its cavity.

04| Appliance suction lost|

  1. The dustbin is full
  2. The central brush or the side brushes are blocked.

|

  1. Empty the dustbin, clean the motor and the filters.
  2. Remove any hair and debris from the brushes. Check that there is no dirt obstructing the robot.

05| The appliance is hard to manoeuvre.|

  1. The wheels are jammed.
  2. The gap and obstacle sensors are dirty.
  3. Problem with the laser module.

|

  1. Clean the vacuum wheels and remove the hair and other debris caught up around them.
  2. Gently clean all of the sensors on the appliance.
  3. Clean the laser module gently with a soft cloth.

06| Scheduling does not work correctly.|

  1. The robot is not switched on.
  2. The robot battery is weak.
  3. The dustbin is full.
  4. Scheduling has been cancelled.

|

  1. Switch the robot on.
  2. Recharge the robot before starting a new cleaning cycle.
  3. Remove the dustbin and empty it before reinserting it.
  4. Check the schedule on the mobile app and reschedule the cleaning cycle, if necessary.

07| Unable to pair the robot with the smartphone|

  1. The smartphone is not connected to the home Wi-Fi network.
  2. The Wi-Fi network is over 2.4 GHz.
  3. The distance between the robot and the smartphone is too great.
  4.  The robot is already paired with another smartphone.

|

  1. Connect your smartphone to the home Wi-Fi network.
  2. Connect your robot to a
  3. 2.4 GHz network.
  4. Move closer to the robot with your smartphone.
  5. Ask the owner user for permission to share the robot.

08| The robot is offline|

  1. The robot has run out of battery.
  2. The robot is not on its home base and is hibernating.

|

  1. Charge the robot using its home base.
  2. Manually exit the robot from hibernate. Press the power button on the robot.

09| The auto- empty station struggles to pick up the dust from the bin|

  1. The dustbin is full
  2. The auto-empty station is not inserted correctly

|

  1. Replace the dust bag if necessary
  2. Place the auto-empty station on a flat surface

If none of the above-mentioned steps provide a solution for your problem, please contact the AMIBOT after-sales department.

Warranty and after-sales service

Support in France
Our AMIBOT customer service department is ready to help you:
By email: support@amibot.tech

NOTE: The warranty does not cover damage caused by rusting, a collision or misuse. Accessories are not covered by the warranty.

Technical specifications

AMIBOT Spirit Premium robot

Classification Specification Value
Dimensions: Diameter 350 mm
Height 100 mm
Weight: 3.6 kg
Electrical specifications Voltage: 14.4 V
Power: 50 W
Battery type 5200 mAh Lithium ion
Noise level 70 dB
Input 24 W
Dust bin capacity: 300 ml
Charge type Automatic
Cleaning Cleaning speed 16.8 m/min
Cleaning modes AUTO, SPOT, MAX, AREAS TO CLEAN, HOME BASE
Charge time 540 min
Max. cleaning time 220 min
Accessories Side brushes, central brush, HEPA filters, cleaning pads, remote

control

Auto-empty station

Classification Specification Value
Dimensions: Length 242 mm
Width 220 mm
Height 393 mm
Weight: 3.4 kg
Settings Voltage: 220 W
Motor power 1050 W +/- 15%
Vacuum time 10 s +/-2
Noise level 85 dB
Capacity 3 l
Water tank capacity: 200 ml
Motor rotation speed 43 000 r/min

NOTE: These specifications could be modified with the objective of continual improvement.

Safety instructions and precautions

Operating conditions
When using an electrical appliance, basic precautions should always be followed, which include:

  • This appliance is not intended to be used by children or any person with reduced physical, sensory or mental capacities, unless they have been given supervision or instruction concerning use of the device from a person responsible for their safety.
  • Do not allow children to play with the appliance.
  • Children should not clean or perform maintenance on the appliance without supervision.
  • The appliance must be kept out of children’s reach while switched on.
  • The appliance must not be used if it has suffered a fall or presents visible signs of damage.
  • Do not use the appliance in extremely hot or cold environments (below 0˚C, above 40˚C).
  • To reduce the risk of electrical shock, do not place the appliance near water or other liquids apart from when using the robot’s water tank.
  • Do not touch the power plug or the appliance with wet hands.
  • For household use only.
  • Only use accessories recommended or supplied by the manufacturer.
  • Please make sure your power supply voltage matches the power voltage marked on the power adapter.
  • Store the appliance away from heat and flammable materials.
  • Do not pull on the appliance’s power cable to avoid causing possible damage.
  • Make sure you do not insert objects in the laser module.
  • Keep the power cable away from sources of heat.
  • Do not use the appliance if the power cable or plug are damaged.
  • Warning: Only use the home base and the power cable supplied by the manufacturer to charge the battery.
  • The robot batteries must only be replaced by qualified persons.
  • Only use AMIBOT Spirit Premium as described in this manual.

Recycling instructions

For EU countries

Robot
Do not incinerate the appliance, even if it is severely damaged. The batteries can explode in a fire.
Do not dispose of this product with other household waste to prevent possible harm to the environment or human health. Recycle the appliance responsibly to promote sustainable reuse of material resources. To recycle your used appliance, please use the return and collection systems or contact the retailer where the product was purchased. They can safely recycle this product.

Battery:
The battery must be removed and discarded according to local laws and regulations.

Batteries
Used batteries must be removed from the appliance and discarded in an appropriate manner.

Packaging
Packaging is necessary, it protects our appliances against possible damage during transportation. If you need to return your robot to the AMIBOT after- sales department or customer service department, the original packaging is the best protection against damages.
If you wish to dispose of your AMIBOT packaging, you can do so after the withdrawal period has expired. AMIBOT packaging is recyclable and should be recycled correctly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals