MINFU BB2742 2×8 Inch Portable Party Speaker User Manual

2×8 Inch Portable
Party Speaker

Model # BB2742 Instruction
Manual Instrucciones

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING YOUR PARTY SPEAKER. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Your Speaker has an internal rechargeable battery. Improper usage may result in the Speaker becoming hot, ignite or bursting and cause injury if exposed to conditions of abuse. Be sure to follow the safety warnings listed below:

1. Do not assemble, throw away or damage the Party Speaker.
2. Store the Party Speaker in a dry place, keeping it away from damp corrosive materials and environments such as salt air.
3. Keep the Speaker away from direct sunlight, fire, and high voltage equipment Do not store the Speaker inside a car during hot weather. Remember a closed car acts as a greenhouse allowing the inside temperature to possibly reach over 200E
4. The Party Speaker is not a toy. Please keep it out of the reach of young children. Please do not discard this rechargeable device as trash. Consult your local waste collection agency for proper disposal or recycling methods. You may also contact
   Call2Recycleaat 877-273-2925 or online at call2Recycle.org* for a battery recycling drop-off location near you.

Battery Information

Your device is powered by a rechargeable battery. The full performance of a new battery is achieved only after two to three complete charge and discharge cycles. The battery can be charged and discharged hundreds of times, but it will eventually wear out.

• Do not leave a fully charged battery connected to a charger, overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time. • Never use any charger that is damaged.
• Leaving the device in hot or cold places will reduce the capacity and lifetime of the battery. The optimal temperature for the battery is between 59°F and 77°F. A device with a hot or cold battery may not work temporarily, even when the battery is fully charged.
• Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Always dispose of batteries according to local regulations. Please recycle. Do not dispose of as household waste.

BATTERY/POWERING UP SPEAKER

The BB2742 is a lithium battery-powered PA loudspeaker. Be sure that you have completely charged the battery prior to first use to maximize the battery’s lifespan. Once the power adaptor(included) is connected to a power source, it will automatically begin charging. The battery indicator light always turns red when charging and turn blue when charged fully. Upon completion of the charging, Please disconnect the unit. The battery can be recharged about 300 times in its lifetime. When not in use the speaker should always be set OFF to prevent the unit from draining the battery. When the unit is not used for prolonged periods of time, the battery will gradually lose its power. It is recommended to fully charge the battery at least every 60 days.

BATTERY CAUTION: Do not disassemble, short circuit, or expose to fire or high temperature. Properly connect specified devices. Recycle batteries according to local, state, and national regulations.
It may damage your hearing if you listen at a high volume for a long time. It is recommended you use the lowest volume possible for listening to music.
WARNING: DO NOT INGEST BATTERY, CHEMICAL BURN HAZARDOUS National Button Battery Ingestion Hotline- 800-498-8666

WARNING!
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER ON THIS SPEAKER. THERE ARE NO USER-SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO A QUALIFIED TECHNICIAN. To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not store or operate this product near any liquids, heat sources such as radiators, or heat registers. Clean only with a dry cloth. Users should exhibit extra safety when this symbol appears in this instruction manual and follow all precautions as they are stated.
Bluetooth®
Bluetooth ® Mode: Make sure the speaker is on bluetooth ® mode. Open the Bluetooth ® of the phone. Find the Bluetooth ® name of the unit called” BB-BT-SP “to connect. After a successful match, you can play the music from the speaker. You won’t need to reconnect the Bluetooth” when switching mode.

DISPLAY SYSTEM SETTINGS

1. Input Mode: The LED display screen will display the information of input mode for USB/MICRO-SD/BT/AUX /FM. When a USB flash drive /MICRO-SD Card is inserted into the USB/MICRO-SD input, the unit will automatically switch to USB/MICRO-SD mode and begin playing Mp3 audio files from the USB flash drive / MICRO-SD Card.
2. Track Number: The tracking number currently playing from the USB/TF will display.
3. FM Mode: All FM channels display here. Short Pressaplay/pause” button for auto-scan all channels. The frequency channels will be within 87.5-108.0MHz.

TRUE TWS CONNECTION

1. TWS connection: TWS connection is only for two speakers, TWS is only supported by the 2 speakers in this bundle.
2. Turn on both of the speakers, and make sure the TWS switch is set to “Slave” on one speaker and “Master” on the other speaker. The 2 speakers will then pair.
3. Press the MODE button on the speaker with the switch set to”Master” to choose AUX/USB/TF/FM. You can enjoy the music from the AUX/USB/TF/FM from the 2 speakers.
4. If need BLUETOOTH ® mode, pls repeat the above operation to make one speaker be a master speaker and another one be slave speaker, open your phone and find the Bluetooth namel1B-BT-SP” to pair, make sure you connected the master speaker, then you can enjoy the music from phone on the two speakers.

Connecting your wired microphone

1. Connect your wired microphone(included) to the Mic Input.
2. Make sure your wired microphone is in the ON position and talk normally.
3. Adjust the Mic Volume to your desired volume level.
4. Adjust the master volume as needed.

REMOTE CONTROL

1. STANDBY: I will put the unit in standby mode.
2. Input Mode Button:Toggle between USB,Micro-SD,FM,AUX,Bluetooth
3. Mute: Mute the track 4. PLAY/PAUSE
4. Previous Track: Select Previous channel
5. Next Track: Select the next channel.
6. EQ: Select EQ mode.
7. VOL-:Reduce the master volume
8. VOL+: Increase the master volume
9. REP: Repeat the playing track.
10. Press to Scan Channel in FM Mode 12-21.KEY Number for selecting the curtain track for USB or Micro-SD.

BB2742 REAR PANEL

1. VOLUME: Adjust from Min to Max
2. TREBLE: Adjust from Min to Max
3. ECHO of Microphone Adjustment: Adjust from Min to Max
4. BASS: Adjust from Min to Max
5. USB Slot/MICRO-SD
6. MODE button: Toggle between AUX, USB, MICRO-SD, FM, BT by Short Press Long Press to turn on/ off the light Previous Track Button: Select the previous track by short press Play/Pause Button by short press Next Track Button: Select next track by short press
7. AUX Input
8. Mic. Volume Knob: Adjust from Min to Max
9. POWER ON/OFF
10. Power Supply: DC 5V 1A
11. Mic. INPUT
12. TWS SWITCH

Connecting your AUX cable

1. Press the mode button until you see”AUX” on the LED screen.
2. You can connect non-Bluetooth devices like computers, and phones using your AUX cable(included), another side plug-in speaker AUX input interface.
3. Play the music from your device, and adjust the volume on your device to your desired level.
4. Adjust the master volume as needed.

Connecting your USB Device

1. Plug your USB device into the USB interface.
2. The model should switch automatically to”USB Mode’:
3. Your speaker will automatically play the first Mp3 song on your USB device.
4. Adjust the volume as needed.
5. Press the Next, Previous, Play/Pause buttons as needed.

Connecting your MICRO-SD Device

1. Plug your MICRO-SD device into the MICRO-SD interface.
2. The model should switch automatically to”TF Mode”.
3. Your speaker will automatically play the first Mp3 song on your MICRO-SD device.
4. Adjust the volume as needed.
5. Press the Next, Previous, Play/Pause buttons as needed.

TRIPOD INSTRUCTION:

1.  Take out the main column from the tripod and assemble them with a sleeve;
2. Insert the screw into the sleeve slot and fasten the screw
3. .Insert the screw into the tripod slot and fasten the screw
4. Insert the lock pin in the hole of the main column to control the height.

LIMITED WARRANTY

 ESI Cases & Accessories, Inc., warrants to the first consumer purchaser that this product, when shipped in its original container to the original purchaser will be free from defective workmanship and materials for one year and agrees that it will, at its option, either repair the defect and replace the defective product or part thereof at no charge to the purchaser for parts or labor for the time periods described. This warranty does not apply to any appearance items of the product nor to the additional excluded item(s) set forth below nor at any Product the exterior of which has been damaged or defaced which design or construction. The limited warranty described herein is in addition to applicable law.
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD FROM THE DATE OF ORIGINAL PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein or to extend the duration of any warranties beyond the time period described herein on the behalf of ESI Cases & Accessories, Inc.
The warranties described herein shall be the sole and exclusive warranties granted by ESI Cases & Accessories, Inc. and shall be the sole and exclusive remedy available to the purchaser corrections of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of ESI Cases & Accessories, Inc. to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract negligence, strict liabilities and responsibilities of ESI Cases & Accessories, Inc. be liable or in any way responsible, for any incidental of consequential damages, so the above exclusion may not apply to you. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE

Manufactured By:
ESI Cases & Accessories
44 East 32nd Street
New York, NY 10016
Tech Support: 212-883-8838
TechSupport@ESICellular.com

Return Instructions

If your speaker malfunctions during the warranty period of one calendar year (90 days for battery), contact our customer service department at 212-883-8838 to obtain troubleshooting information. If troubleshooting assistance fails to remedy the problem, you will receive a return authorization # and instructions for sending your unit to our Service Center. Your return authorization number must be clearly visible and placed on the outside of the box when the unit is returned. Enclose a copy of your original proof of purchase showing the original purchase date, along with detailed information describing the exact nature of your problem. Be sure to include your complete name, address, email address, and daytime and evening contact numbers. In addition, please send a check or money order made payable to”ESI Cases & Accessories “for the return freight amount (given to you by our service agents). All of the above must be included with your return, or your package will not be eligible for service under our warranty. The customer is responsible for packing the speaker in it’s original carton or equivalent, and for ensuring, and shipping the unit to our service center. Please make sure to pack all accessories included with your speaker so that we can properly identify any issues. All freight costs to return the unit to ESI Cases & Accessories., are the responsibility of the customer. If your speaker is under warranty, then ESI Cases & Accessories. will at its sole discretion, exchange or repair the speaker without charge for parts and labor. The customer is responsible for return freight and should include a check or money order payable to”ESI Cases & Accessories.” with your return for the return freight amount. Any shipments received without a Return Authorization number will be refused. For more details please contact our customer service department.

Send product:
ESI Cases & Accessories
44 East 32nd Street
New York, NY 10016
Tech Support: 212-883-8838
TechSupport@ESICellular.com

FCC Information

FCC ID: OGGK3BB2742 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. Federal Communications Commission (FCC) StatementThis Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV/technician for help.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Tested to comply with FCC standards. FOR HOME OR OFFICE USE. Warning: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co-located or in conjunction with any other antenna or transmitter.
© 2020 Billboard IP Holdings, LLC. All rights reserved. Billboard°, the Billboard logo, HOT 100, And associated characters, trademarks, and design elements are owned and licensed by Billboard IP Holdings, LLC.
Bluetooth is a registered trademark of Bluetooth SIG All other trademarks are property of their respective companies.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>