Auverte C590 USB Rf-Bridge User Manual
- June 5, 2024
- AuVerte
Table of Contents
Auverte C590 USB Rf-Bridge
Functions
- Connects a laptop and tablet with the AuVerte Rf mesh network.
- Infrared (IR) code capture for HVAC and A/V remote controls
The C590 is a companion product that is used in conjunction with the AvEWB
software. The bridge performs as a transparent and bi-directional router that
connects the PC application to actively participate in the AuVerte Rf mesh
network.
- C5xx Ondur Thermostat
- GK101 Optical Door/Window Sensor
- GK104 Aux. Temperature/Humidity Sensor
Specifications
User Interface
| Display | OLED white, 128×64 pixels |
|---|---|
| Keys | Three capacitive touch sensors (up, mode, down) |
| Keypad backlight | LED, white |
| Temperature sensor | 10 °C to 35 °C, accuracy +/- 1 °C |
| Light sensor | Measurement of environmental light level for automatic backlight |
control
Radio
| Standard | IEEE 802.15.4 |
|---|---|
| Frequency band | ISM 2.4 GHz |
| Interference immunity | DSSS (Direct sequence spread spectrum) |
| Data rate | 250 kbps |
| Antenna | Build-in |
| Indoor range | Up to 50 m (150 ft) |
| Transmit power | +3 dBm |
| Receiver sensitivity | -95 dBm |
| Channels | 16 (11 to 26, default 25) |
| Protocol | AuVerte mesh, IPv6 over 802.15.4 with forward error correction (FEC- |
ECC)
Software
| IPv4 | ICMP, IP, UDP, DHCP |
|---|---|
| IPv6 | ICMPv6, IP, UDP |
| Encryption | AES128 |
| Hashing | SHA256, AES-CMAC |
| Key Exchange | ECDH |
| Routing | UDP – AuVerte mesh |
IPv6 – IPv6 over 802.15.4
App Security| DTLS
Cyber security| Packet authentication, packet inspection, certificate-based
access control, configurable encryption keys with no backdoors
Device
| Power | 5VDC from USB port |
|---|---|
| USB connect | USB Type-C |
Environmental and Physical Specification
| Dimensions | 48.8mm x 28.5mm x 19mm |
|---|---|
| Weight | 0.060 kg (2.1 oz) |
| Operating temperature | 10 °C to 40 °C (50 °F to 104 °F) |
| Storage temperature | -20 °C to 70 °C (–4 °F to 158 °F) |
| Operating humidity | 10 % to 95 %RH, non-condensing |
| Storage humidity | 5 % to 90 %RH, non-condensing |
| Electromagnetic emissions | FCC Part 15 Class A EN 62311 (EMR) |
ETSI EN 300 328 (2.5GHz ISM Band)
ETSI EN 301489 (EMC)
Safety approvals| EN 60950
Environmental| RoHS
Cleaning| Mild cleaning liquid, soft towel
Recycling| 32g ABS, 7g polycarbonate, 21g electronics
Ordering Information
| Part numbers | 003090.C590 USB Rf-Bridge |
|---|---|
| Package content | USB Rf-Bridge |
| Color Options | n Default |
| Options | None |
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.