myStage B2K Bluetooth Speaker and Microphone User Manual

myStage B2K Bluetooth Speaker and Microphone

OVERVIEW

• LED Color:
• Power LED:
• 3 colors RED/ BLUE /YELLOW /BT LED:
• BLUE /MIC LED: BLUE

Turn On/Off

1. Turn On: When the speaker is off, press the power button ( O,2 seconds) When the power is turned on, the power LED ight turns blue. When the power is turned on, the speaker will play the notification sound (POWER ON)
   When charging, press the power button shortly, then the speaker will turn on.

2. Turn Off: When the speaker is on, press the power button (,2 seconds).
   When the power is turned off, the power LED will flash on red light twice, then it will be turned off.
   When the power is turned off, the speaker will play the notification sound (POWER OFF) When charging, press the power button shortly, then the speaker will turn off.

3. When it is in Bluetooth mode and the speaker doesn’t pair anything within 10 minutes, the speaker turns off automatically.
   If the speaker is plugged thru USB memory or AUX, it doesn’t turn off automatically.

4. When Bluetooth or MIC LED is working on, the LED light is flashing.

Speaker volume control (Music volume)

1. The volume controller can control music volume only not microphone volume,
2. There are ten music volume levels, Vol, O means no sound, Sound level starts from Vol.
3. you press the Vol UP button (+) shortly, the volume level goes up to just 1 level,
4. you press the Vol UP button (+) for about 2 seconds, the volume level can go to the max volume level Vol9.
5. the volume level is Vol 5 and it changed, the changed volume level will be retained, which ill be the initial volume level next time,
   If you press the Vol DOVWN button () shortly, the volume level goes down to just 1 level, If you long-press the Vol DOWN button () for about 2 seconds, the volume level will be mute
   In mute mode, press the Vol UP button (+) or Vol DOWN (, the music volume will be back to the previous level, There is notification sounds for each volume level,.

Play (USB or Bluetooth)

1. Play: When the speaker is paused or stopped, press the play/pause button (Iu) shortly.
2. Pause: When the speaker is playing, press the play/pause button ( >u ) shortly.
3. Previous: Press the left button () shortly on the navigator,
4. Next: Press the right button (-0) shortly on the navigator,

Input mode

1. if you long-press play/pause button ( >I) for about 2 seconds, you can set the input mode

2. The input order is following like this: BluetoothUSBAUX Bluetooth
   Each input mode has its own notification sound. (“Bluetooth MODE”, “USB MODE”, “AUX MODE”)
   USB, AUX mode can only be changed when USB, AUX is plugged into the speaker.
   0f a USB memory isn’t plugged into the USB port, the input order is following like this: Bluetooth AUX Bluetooth)
   The default input is Bluetooth

3. If the USB memory is plugged into the USB port, the USB is the default input mode.

4. When the speaker is set on another mode, like a USB memory is being plugged into the speaker, the speaker will turn into USB mode and play the file by itself, which is in the USB memory.

Connect a Bluetooth device

1. Bluetooth ID: “B2K- MAGIC SING”

2. If you turn on the speaker, the speaker will be trying to connect a Bluetooth device.
   When the speaker is trying to connect a Bluetooth device, Bluetooth LED will iash.

3. If the pairing doesn’t succeed within 30 seconds, the speaker will stop connecting by itself. In this case, Bluetooth LED will be turned off.

4. if you want to connect a Bluetooth device, long-press the left button ()on the navigator.

5. If the speaker connects to a Bluetooth device, the speaker will play the notification sound (Bluetooth connected)
   In this case, Bluetooth LED will flash.

6. If you want to disconnect a Bluetooth device, long-press the left button (8-) on the navigator.
   In this case, the speaker disconnects to the Bluetooth device and then searches for another Bluetooth device to pair with it.
   While doing this, Bluetooth LED is flashing.

Microphone

1. Turn on: When the microphone is turned off, long press the right button () for about 2 seconds on the navigator.
   When the microphone is turned on, Mic LED il lash. If the microphone is connected to the speaker, Mic LED light will remain turned on. When the microphone is turned on, the speaker will play the notification sound.

2. Turn off: When the microphone is turned on, long press the right button()for about 2 seconds on the navigator.

3. When the microphone is turned off or disconnected, Mic LED will flash.
   If the microphone can’t be succeeded to connect within 5 minutes, the microphone will be turned off automatically.

EQ mode

Select the 4 types of EQ mode by the remote control
[DEFAULT]: Default mode
[MEGA BASE]: Bass boost mode
.[POP]: Optimizing for pop
[MAGICSINGJ: Optimizing for a MAGIC SING karaoke app

Notification sound

lf the notification sound key is turned on, the speaker plays the notification sound.
These buttons contain notification sounds: Power, Input, Volume, EQ mode f the notification sound key is turned off, all notification sounds won’t be played through the speaker.

LOW Battery indication

1. When the battery is going down below 20%, Power LED will flash on orange light every 1 second.
2. When the battery is going down below 5%, Power LED wil fash on orange light every 1/2 second. The speaker will play the notification sound (“Low Battery”) every 1 minute.

Charging

1. USB cable (Micro5pin) is plugged into the port at the back of the speaker, the battery starts to charge and Power LED will lash on red light.
2. When fully charged, Power LED will turn red light and then it will stop charging.

Remote Control

1. Power: I you press the power button on the remote control, the speaker will finish the power-saving mode or it will be the power-saving mode. When finishing the power saving mode,
   the speaker will play the notification sound (“POWER ON +MODE) When it’s going to the power-saving mode, a red LED light will flash twice and the speaker will play the notification sound (OF

2. Bluetooth: The speaker starts the pairing process again.

3. Mute: Turn on/mute. If mute is turned on, the speaker will play the notification sound (“‘MUTE”)

4. +- Volume UP/DOWN

5. Pay or pause the music.

6. Previous or next song

7. Bluetooth, USB, AUX: Select the input mode among Bluetooth, USB memory, and AUX mode

8. EQ: Select the 4 types of EQ mode. When it changes the mode, the speaker will play each of the notification sounds.

9. Voice ON/OFF : Turn on/off the notification sound.

10. Mic: Turn on/off the microphone.

Pairing the microphone

1. Standby mode: If there isn’t any button input within 10 seconds, the speaker will be on standby mode.

2. Change mode: Press the MODE button to change the mode.
   The changing order is the following like this: Mic Vol Speaker VolEcho Channel Notification sound.

3. Microphone volume: Press the “A” “button to adjust the microphone volume (0-9).

4. Speaker volume: Press the “A” “”button to adjust the speaker volume.

5. Echo volume: Press “A” V” button to adjust the echo volume.

6. Channel: Press “A” “V” button to adjust the channel from A1 to B8. (1-8)
   Initial LCD indicates the present channel When the channel is adjusted, only the frequency will be changed. It won’t pair.
   Long Press the MODE button for about 3 seconds, and the speaker will pair with a Bluetooth device as the current channel.
   During the pairing process, LED will flash for about 3 seconds. (0.7 sec ON, 0.3 sec OFF

FCC

FCC Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Part 15.21
Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement
This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment.
This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>