ZK-MG PEMENOL DC Motor Speed Controller Signal Generator User Manual
- June 5, 2024
- PEMENOL
Table of Contents
ZK-MG PEMENOL DC Motor Speed Controller Signal Generator
Brief Intro:
The module is a high-power PWM DC motor governor. It can adjust the motor
speed by adjusting the duty cycle of the output signal. It can also adjust the
output frequency to match the frequency of the output signal to the motor
frequency, allowing the motor to work more stably. It can be widely used for
drive motor/light brightness controlling/speed controlling/signal generator,
etc.
PS: This module is a PMW driver, not a voltage converter. It has no
function to change the output voltage, so the output voltage and input voltage
are the same.
Product Highlights
- Support ON/OFF output
- Soft start function
- Support set duty cycle
- Support set frequency
- Adjustable digital encoder
- Support reverse connection protection
- Support parameter memory function
- Instrument case
Parameters
- Working Voltage: DC 5V-30V
- Rated Current:5A
- Peak Current: 15A
- Power: 150W(Max)
- Work Frequency: 1KHz-99KHz
- Frequency Accuracy: 1%
- Frequency Resolution: 1KHz
- Duty Cycle: 0%-100%
- Duty Cycle Resolution: 1%
- Work temperature: -40~85℃
- Working Humidity: 0%-95%RH
How to use it ? Please note !!!
- Connect the DC 5V-30V voltage
- Press the potentiometer to turn OFF output.
- Press and hold potentiometer to enter into parameter setting mode.
- Press the potentiometer to select setting parameters.
- Rotate potentiometer to set parameter value.
- Set another two parameters as step3 and step4.
- Press and hold potentiometer to save parameters and quit setting mode to normal display mode.
- Connect load as wiring diagram.
- Press potentiometer to turn ON output.
Potentiometer introduction:
Press and hold means keeping press for more than 3 second. Default display duty cycle.
P- 1 Normal display mode:
- Press potentiometer: Turn ON/OFF output signal.
- Press and hold potentiometer: Enter parameter setting mode.
- Rotate potentiometer clockwise: Increase duty cycle value.
- Rotate potentiometer counterclockwise: Decrease duty cycle value.
P-2 Parameter setting mode:
-
Press potentiometer: Select the parameter you want to set including Lower Limit Value of duty cycle, Upper Limit Value and Output Frequency, which could be switched by yourself. Note: The lower limit of the duty cycle is displayed as “L” + two digits; The upper limit of the duty cycle is displayed as “H” + two digits or “100”; And the operating frequency is
displayed as “F” + two digits. -
Press and hold potentiometer: Save parameter and quit setting mode to normal display mode.
-
Rotate potentiometer clockwise: Increase the setting value.
-
Rotate potentiometer counterclockwise:Decrease the setting value.
Stop pads Inside: It is used to connect to an external switch button to turn ON/OFF output if user need control output by another button or controller.
Warm Tips
Please read the user manual carefully before use, make sure that the
parameters of the device you are using are within the specified parameter
range, and carefully check whether the wiring method and setting method are
correct.
Frequently asked questions
-
Q1：Why does this module cannot change the device voltage？
A1：The module is a PMW driver, which controls the controlled device by changing the frequency and duty cycle of the output signal. It is not a voltage converter, it has no function to change the output voltage. -
Q2: Why is this controller not working ?
A2：Please check whether your wiring connection and the setting method is correct, if there are still problems, don’t hesitate to contact us. -
Q3: Why does this controller cannot be turned on?
A3: The potentiometer can be used as a switch to Turn ON/OFF output signal.
Please refer to the potentiometer introduction above for specific operations. -
Q4: Why did the controller stop working after a period of use?
A4: It may be a short circuit. Please check your wiring diagram carefully for correct connection, if there are still problems, don’t hesitate to contact us.
Package Listing:
1>.1pcs High-Power PWM DC Motor Speed Controller
After-Sales:
- We have always been keen to provide customers with the best quality service at the most competitive price.
- Looking forward to get progress and growth with all of you.
- For more product questions and inquiries, please send your advice to sameiyi@163.com
- Thank you for your purchase!
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>