SNAPTAIN A10 Mini Foldable Drone User Manual

June 5, 2024
SNAPTAIN

SNAPTAIN LOGO A10 Mini Foldable Drone
User Manual Mini Foldable Drone
Please read this manual carefully before flying and keep it well for future use.

DISCLAIMER AND SAFETY GUIDELINES

  1. DO NOT look directly into the drone light.
  2. DO NOT treat the product as household waste.
  3. DO NOT fly above or near obstacles, crowds, open water, public road, high voltage power lines, or trees.SNAPTAIN A10 Mini Foldable Drone - FIG 3
  4. DO NOT use the drone in severe weather conditions. These include wind, snow, rain, smog, hail, lightning, tornadoes, or hurricanes.SNAPTAIN A10 Mini Foldable Drone - FIG 4
  5. Stay away from the rotating propellers and motors to avoid some tiny objects (e.g. hair) to get into them.
  6. This product is not a toy and is not recommended for users under age 14.
  7. Please maintain the line of sight of your drone at all times after it is powered up. Do not rely on the camera image to control your drone.
  8. This drone does not come with a GPS module. Please fly the drone within the control range and always keep an eye on the flying.
  9. This product is not intended for professional aerial drone photography.
  10. Be sure to observe all local regulations, obtain appropriate authorizations and understand risks. Please note it is solely your responsibility to comply with all flight regulations.

SNAPTAIN accepts no liability for damage, injury, or any legal responsibility incurred directly or indirectly from the use of this product. The user shall observe safe and lawful practices including, but not limited to, those set forth in these Safety Guidelines. SNAPTAIN reserves the right to update this user manual.
**** We use this symbol in this user manual to draw your attention A to some important tips.

MAINTENANCE AND CARE

  1. Thoroughly check the drone after a crash or violent impact.
  2. Do not charge the battery if it is hot. Let it cool down first.
  3. Remove the batteries from both the drone and the remote if they will not be used for a long time.
  4. Unplug the charger once the battery is fully charged.
  5. Store the drone and remote in a cool, dry place away from direct sunlight.
  6. Avoid direct contact of the camera with water or other liquids. Wipe dry with a soft absorbent cloth if it gets wet.
  7. Do not charge the battery next to inflammable materials, such as carpet, wood floors or countertops, etc., or on surfaces that are electrically conductive. Do not leave the battery unattended while charging.
  8. Please use the original battery provided. Using an incorrect type of battery may lead to fire hazards.
  9. Do not dispose of the battery in a fire or a hot oven, cut or mechanically crush the battery, as this may cause explosions.
  10. Do not leave the battery in an extremely high-temperature environment that can result in an explosion or the leakage of flammable liquid or gas.
  11. Do not expose the battery to extremely low air pressure, as this may result in an explosion or the leakage of flammable liquid or gas.

 PACKING LIST

SNAPTAIN A10 Mini Foldable Drone - FIG 11

PRODUCT OVERVIEW

Drone

SNAPTAIN A10 Mini Foldable Drone - FIG 12

Remote

SNAPTAIN A10 Mini Foldable Drone - FIG 13

  1. Photo
  2. Speed Switch(short press) Emergency Stop(long press)
  3. Video
  4. 360° Flip

SNAPTAIN A10 Mini Foldable Drone - FIG 14

1. Phone Clamp 8. LED Indicator
2. Left Control Stick 9. Right Control Stick
3. ON/OFF 10. Drone’s LED Indicators ON/OFF
4. One Key Take-off/Landing 11. Forward Trim
5. Circle Fly 12. Rightward Trim
6. Headless Mode(short press) One Key Return(long press) 13. Backward Trim
7. High-speed Rotation 14. Leftward Trim

FLIGHT PREPARATION

  1. Unfold the rear arm, then the front arm.SNAPTAIN A10 Mini Foldable Drone - FIG 15
  2. Gently pull the buckle of the propeller guard to both sides and align the slot with the motor base, then fit the propeller guard into the drone’s arm.SNAPTAIN A10 Mini Foldable Drone - FIG 16
  3. Charge the drone battery.SNAPTAIN A10 Mini Foldable Drone - FIG 17 Notes:
  • When the drone’s battery is low, there are continuous beeps from the remote and the drone’s LEDs keep flashing.
  • Please use the original battery and USB cable provided.
  • Keep the battery away from any sharp objects that could puncture the battery to avoid risks of explosion and fire.
  • It’s not recommended to charge the battery from the USB port of the PC.
  • Battery capacity may be reduced when flying in low-temperature environments. Flight time may be reduced, too. 4. Install the battery into the drone after it’s fully charged.SNAPTAIN A10 Mini Foldable Drone - FIG 18 5. Install the remote batteries.SNAPTAIN A10 Mini Foldable Drone - FIG 19* When the remote’s battery is low, there are continuous beeps from the remote and its LED indicator keeps flashing. 6. Unfold the phone clamp to mount your mobile device. SNAPTAIN A10 Mini Foldable Drone - FIG 20 7. Replace the propellers when it’s needed. (Optional)

SNAPTAIN A10 Mini Foldable Drone - FIG 21

  1. Loosen the screws, then remove the cap.
  2. Take out the propellers.
  3. Fit the spare propellers into the drone according to the mark (A/B) on them.
  4. Install the cap and tighten the screws.

Note: Please do not overtighten the screws. Gently rotate the propellers by hand after installation to check if they are rotatable, if not, please loosen the screw and check again.

FLIGHT OPERATION GUIDE

IMPORTANT

  • Make sure you power on the drone first, then the remote on each flight.
  • Do repeat the pairing and calibration procedure each time the drone or remote is restarted.
  • For all flight functions and modes, the operator and tail of the drone must be aligned.
  • We recommend flying in the open air and within the control range for beginners.

Remote Operation Guide
Pair the Remote with the Drone
Step 1:

Press and hold the ON/OFF button till the drone’s LEDs start flashing to turn on the drone. Then place the drone on a flat surface with the head forward.SNAPTAIN A10 Mini Foldable Drone - FIG 22

Note: The drone will be off automatically if you do not operate it about 6mins after powering on the drone.
Step 2:
Press and hold the ON/OFF button to turn on the remote; you will hear a beep from the remote and its LED indicator starts flashing.SNAPTAIN A10 Mini
Foldable Drone - FIG 23

**Notes:* The remote will be off automatically if you do not operate it about 6mins after powering on the remote.

  • Press and hold the ON/OFF button again to turn off the remote.
    Step 3:
    Push the Left Control Stick forward to the top, then pull it back to the bottom. Pairing is successful when the LEDs of the drone turn solid on from flashing.SNAPTAIN A10 Mini Foldable Drone - FIG 24

2. Flight Calibration
Move both control sticks to the lower left at 45°; you’ll hear a beep from the remote. Calibration completes when the LEDs of the drone turn solid on from flashing.SNAPTAIN A10 Mini Foldable Drone - FIG 25

**Note: Please calibrate the drone after a crash or impact.
3. Flight Instructions
Take-off
Option 1:** Press the button to take off.![SNAPTAIN A10 Mini Foldable Drone

Option 2:
Simultaneously push the Left Control Stick to the lower left at 45° and the Right Control Stick to the lower right at 45° (or push the Left Control Stick to the lower right at 45° and the Right Control Stick to the lower left at 45°) until the four propellers start rotating, then slowly push the Left Control Stick forward to take off.

SNAPTAIN A10 Mini Foldable Drone - FIG 28

Option 3:
Place the drone on your palm with the head of the drone in the front, then gently throw it into the air.SNAPTAIN A10 Mini Foldable Drone - FIG
29

Landing
Option 1: Press the button to land the drone.SNAPTAIN A10 Mini Foldable
Drone - FIG 30

Option 2:
Slowly pull the Left Control Stick backward to land the drone until the propellers stop rotating.SNAPTAIN A10 Mini Foldable Drone - FIG
31

Flight Directions
Left Control Stick

| | Push the Left Control Stick forward and the drone will ascend; pull it backward and the drone will descend.
---|---|---
| | Pull the Left Control Stick leftward and the drone will rotate to the left; pull it rightward and the drone will rotate to the right.

Right Control Stick

| | Push the Right Control Stick forward and the drone will fly forward; pull it backward and the drone will fly backward
---|---|---
| | Pull the Right Control Stick leftward and the drone will fly leftward; pull it rightward and the drone will fly rightward.

Flight Trimming

| SNAPTAIN A10 Mini Foldable Drone - FIG 63| If the drone drifts forward or backward when hovering, press the Backward Trim button or the Forward Trim button to adjust.
---|---|---
| SNAPTAIN A10 Mini Foldable Drone - FIG 64| If the drone drifts leftward or rightward when hovering, press the Rightward Trim button or the Leftward Trim button to adjust.

Speed Switch
The drone is set to low speed by default.
Press the SPEED button once for Medium speed and there are two beeps from the remote. Press it again for High speed and there are three beeps from the remote.
SNAPTAIN A10 Mini Foldable Drone - FIG 65

Press it the third time to get back to Low speed and there is one beep from the remote.
Headless Mode
Short press the button to activate Headless Mode; LEDs on the drone start flashing.
In this mode, the drone will fly following the direction of the Right Control Stick regardless of the position of your drone’s head or tail.SNAPTAIN A10 Mini Foldable Drone - FIG 66

Press the same button to exit this mode; LEDs on the drone turn solid.
360° Flip
Fly the drone to a height over 2m, then press the 3D FLIP button to activate the 360° Flip function. Next, move the Right Control Stick to flip the drone accordingly.SNAPTAIN A10 Mini Foldable Drone - FIG
67

Notes:

  • There are continuous beeps from the remote when you activate this function. If you do not move the Right Control Stick about 5s after you press the 3D FLIP button, the function will be canceled and the remote will stop beeping.
  • This function can’t be activated when the battery of the drone is low.
    One Key Return
    Press and hold the button, then the drone will fly toward its back following a path parallel to its original take-off path. The LEDs on the drone keep flashing when the drone is returning.
    Press and hold the button again or move the Right Control Stick forward to cancel this mode, or the drone will keep flying back.SNAPTAIN A10 Mini
Foldable Drone - FIG 40

High-Speed Rotation
Press the button to make the drone rotate at high speed.
Press the button again or move the Right Control Stick in any direction to exit this mode.SNAPTAIN A10 Mini Foldable Drone - FIG
41

Note: This function can’t be activated when the battery of the drone is low.
Circle Fly
In the case of barrier-free within a 5m radius around the drone, press the button to fly the drone in a circle.
Press the button again or move the Right Control Stick in any direction to exit this mode.SNAPTAIN A10 Mini Foldable Drone - FIG
42

Note: This function can’t be activated when the battery of the drone is low.

Photo/Video
Please connect the drone to your mobile device first (refer to Page20), then go to the App Snaptain Air to check your photos and videos.
Press the button to take a photo.SNAPTAIN A10 Mini Foldable Drone - FIG
46

Press the button to start recording a video; press it again to stop recording and save the video.SNAPTAIN A10 Mini Foldable Drone - FIG
47

Altitude Hold/Hover
This is one of the default settings of the drone. When you release the Left Control Stick after an ascent/descent action, the drone will hover at the current flight height. For a stable flight, press the trim buttons to adjust accordingly.
Emergency Stop
Press and hold the and fall SPEED button, then the drone will stop in the air and fall.SNAPTAIN A10 Mini Foldable Drone - FIG 48

Note: It’s NOT recommended to use this function during normal flights for landing, which may result in serious damage to your drone.

App Operation Guide
1. App Downloading and Installation
Download and install Snaptain Air into your mobile device from App Store”/Google Play or by scanning the QR code below.

SNAPTAIN A10 Mini Foldable Drone - QR Code 1For Android 4.4 or later| SNAPTAIN A10 Mini Foldable Drone - QR Code
2For iOS 9.0 or later
---|---

Note: Google Play is a trademark of Google Inc., and App store™ is a trademark of App Inc.
2. Pair the App with the Drone
Step 1:
Press and hold the ON/OFF button till the drone’s LEDs start flashing to turn on the drone. Then place the drone on a flat surface with the head forward.
Step 2:
Go to the Wifi settings of your mobile device and connect to the Wi-Fi Snaptain-A10-xxxxxx.
Step 3:

Open the Snaptain Air App and slide to the interface of A10. Tap Function Display and ON/OFF to turn on the App. LEDs on the drone turn to solid at a successful connection.SNAPTAIN A10 Mini Foldable Drone - FIG
49

Step 4:
Tap , then tap to calibrate the drone.

Notes:

  • If Snaptain-A10-xxxxxx is not listed or the App doesn’t show the preview image, please restart the drone and search the Wifi of the drone again.
  • Make sure the Wifi Snaptain-A10-xxxxxx is only connected to one device.
  • The drone’s Wifi has no Internet access. To prevent your mobile device from automatically switching to cellular data, it’s recommended that you turn off cellular data when connecting to the drone’s Wifi.
    3. Function Overview of the AppSNAPTAIN A10 Mini Foldable Drone - FIG
52
1. Back 6. G-Sensor Mode
2. Photo 7. App ON/OFF
3. Video 8. 360° Flip
4. Media Gallery 9. One Key Return
5. Speed Switch 10. More
A. Gestures for photo/video J. Trim forward/backward
--- ---
B. Drone Battery Status K. Forward/Backward/ Leftward/Rightward
C. Turn Left/Turn Right/ Ascend/Descend L. Trim leftward/rightward
D. VR Mode M. Scale
E. Headless Mode N. Emergency Stop
F. Trajectory Flight O. Wifi Signal
G. Calibration P. Trim clockwise/ anticlockwise
H. Voice Control Q. One Key Take-off
I. One Key Landing

Note: The Left/Right Control Stick appears when you tap on the blank area on the left/right side of the screen.
More:
Tap to show or hide icons from D to H.
Photo:
Tap once to take a photo.
Video:
Tap once to start recording, tap again to end, and save the video.
Media Gallery:
Tap to check the photos and videos saved to the mobile device.
G-Sensor Mode:
Tap to activate this mode. The drone will fly following the inclines of your mobile device in its landscape orientation.
VR Mode:
VR device (not included) is required to activate VR Mode.
Calibration:
Tap to calibrate the drone directly.
If the LEDs of the drone flash quickly after a sudden impact, please tap to calibrate the drone.
Voice Control:
Take off, landing, forward, backward, left, right.
Gestures for Photo/Video:
Tap to activate this function. Within a distance of 2-3m between you and the camera, please face the camera and make an gesture with your right hand to take a photo, a gesture to start/end recording a video.
Wifi Signal:
Check the Wifi status of the drone to avoid losing control. When it drops to 2 or 1 bar, please do not fly the drone far away.
Battery Status:
Check the battery status of the drone.
Trajectory Flight:
Tap to activate this mode. Draw a path in the blank area on the right side of the screen and the drone will fly following the path.
Tap to modify flight distance and time accordingly. Tap again to exit this mode.

SNAPTAIN A10 Mini Foldable Drone - FIG 62

Note: To fly the drone with the remote and see the image through your mobile device in the App operation mode, tap the ON/OFF icon to OFF, then pair the drone with the remote again.

 PARAMETERS

Motor 716 Coreless
Control Range <- 80m
FPV Range <- 25m
Maximum Flight Relative Height  15m
Flight Time  7mins
Charging Time  45mins
Photo Format  JPG
Video Format  MP4
Storage Save to the mobile device
Mobile APP Requirement Android 4.4 or later, iOS 9.0 or later

TROUBLESHOOTING GUIDE

Ql. How to avoid losing my drone?
* Make sure the distance between the drone and the remote/App is effective.

  • We recommend flying the drone on windless days. If you insist on flying the drone in the wind, we recommend flying at HIGH speed.
  • It’s essential to calibrate the drone before flying.
    Q2. Drone LEDs do not light up.
    * Ensure that you’ve turned on the drone.
  • Replace or charge the drone battery.
    Q3. Drone LEDs keep flashing, but the drone never responds to any command from the remote.
    * Pair the drone and remote again.
  • Replace or charge the drone battery.
  • Make sure the batteries of the remote have enough power.
    Q4. The flight is not stable.
  • Return the drone and restart it to do a flight calibration as instructed.
  • Make the flight trimming accordingly.
  • Fly the drone when the weather is good.
    Q5. The response from the drone to the control is not sensitive.
    * Make sure the distance between the drone and the remote is effective.
  • The remote signal may interfere, please land the drone and go to another place to fly it.
    Q6. The connection between the drone and the App is frequently lost.
    * Make sure the distance between the drone and the mobile device is effective.
  • Make sure your mobile device is not connected to another network.
    Q7. The App doesn’t respond to voice commands.
  • Ensure the drone App has access to the audio function of your mobile device.
    Q8. Some of the functions don’t work in the App.
    * Make sure the switch for the App is ON.
    Q9. The drone will fly beyond the control range.
  • Activate the Headless Mode, then move the Right Control Stick to fly the drone back.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

For R/C QUADCOPTER
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISEDC Warning
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

For R/C QUADCOPTER
The device is in compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. The minimum distance from the body to use the device is 20cm.

For Remote
The device is in compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.

CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

| The symbol indicates DC voltage
---|---
| RECYCLING

This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
The user has the choice to give his product to a competent recycling organization or to the retailer when he buys new electrical or electronic equipment. This product can be used across EU member states.

Recycle Icon| BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY
---|---
****| Refer to the user manual and relevant text.
| Operate the product according to the instructions.

Manufacturer
Shenzhen VanTop Technology & Innovation Co., Ltd.
Manufacturer address: 5
02, 5th Flr. BLDG 4, VinQi Technology Park, No. 65 Lishan Road, Taoyuan Street,
Nanshan District, Shenzhen, China
EC/REP
BellaCocool GmbH
PettenkoferstraRe 18,10247,
Berlin, Germany
info@bellacocool.de 
SNAPTAIN SUPPORT
US: support@snaptain.com
CA: support@snaptain.com
UK: support.uk@snaptain.com

| SNAPTAIN A10 Mini Foldable Drone - QR Code 4| SNAPTAIN A10 Mini Foldable Drone - QR Code 5
---|---|---
https://qrs.ly/3zbd6ne
www.snaptain.com | https://qrs.ly/kvbd6nc
@snaptainofficial| https://qrs.ly/3zbd6ne
@snaptain_official

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals