outline FASTQC-LS Fast Quality Control User Manual
- June 5, 2024
- outline
Table of Contents
FASTQC-LS
FAST QUALITY CONTROL
User Manual
SAFETY REGULATIONS
In order to avoid risks for the user’s and other people’s safety, as well as annulling the warranty, it is advisable to read the suggestions in this section for the correct use of the product.
- Do not expose the unit to rain or use it in locations with a high humidity level.
- Ensure that no liquids or solid objects accidentally enter the unit; should this occur, stop using the unit and contact OUTLINE or specialist staff.
- When connecting the unit, ALWAYS check ground connection as required by technical and safety norms.
- If the original connector cable is worn or damaged, it must be replaced with another of the same type (in perfect condition).
- Carry out connections in an orderly manner, only allowing access to experienced specialist staff.
- The unit must only be opened and/or repaired by specialist staff.
- For any requirements of a technical nature, contact OUTLINE or authorized staff.
- The unit is dedicated to moving heavy or bulk objects. For this reason, it must be used under the supervision of experienced personnel.
DISPOSAL OF WASTE MATERIALS
Your product is designed and manufactured with high-quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2012/19/EU and subsequent amendments. This means that the product must NOT be disposed of with other household-type waste. It is the users’ responsibility to dispose of their waste electrical and electronic equipment by handing it over to an approved processor. For more information about where you can send your equipment for recycling, please contact your local distributor. The correct disposal of your old product will help prevent potential negative consequences for the environment and human health.
CONFORMITY AND WARRANTY
All the Outline electro-acoustic and electronic devices are in conformity with
the provisions of EC/EU directives (as stated in our CE declaration of
conformity).
The CE declaration of conformity is attached to the product warranty
certificate and is shipped with the product.
SYSTEM DESCRIPTION
The target of this device is to identify macroscopic damages (like disconnected wires, blown coils, etc…) for each way of the Outline speakers quickly and without the need of an external mains power. In order to perform the measurement, you have to connect a single speaker to one connector on the device via a short link cable, select the measurement preset and to push the “MEASURE” button. The result is shown on the display and via the colored LEDs for each active way.
UNPACKING
After unpacking the device, check very carefully for any damage. If any
damage is found, please notify your dealer. It is advisable to keep the
packaging for use in the event of the unit being transported in the future.
FRONT PANEL
-
- POWER EXCLUSION: connects and disconnects the battery. To turn on the device push one of the four buttons; about thirty seconds after the last activity the device automatically switches off (no power consumption). In order to reactivate it press one of the four buttons;
-
- 9V BATTERY HOUSING: standard single 9V battery housing;
- 3 & 4) CONNECTORS: two connectors are available (one NL4 and one LKI8) to connect the loudspeaker to test;
-
- DISPLAY: shows the name of the selected preset, the name of each way and, during the test phases, more information about the detected issues;
-
- REPORT: test results for each way are also shown via colored LEDs.;
-
- “MEASURE” BUTTON: run the measurement;
-
- “BACKLIGHT” BUTTON: enables and disables the display backlight. Ten seconds after the last use, the backlight turns off automatically; to reactivate it press one of the buttons.
- 9 & 10) SCROLL BUTTONS: used to scroll the list of the measurement presets.
DEVICE USE
-
Power up: after checking the presence of the battery and its good condition switch the power exclusion button(1) in the active position. Push any button to activate the device. (7/8/9/10).
During the start-up, the display shows the firmware version. Afterward, the temperature measured by the internal sensor and the estimated battery charging level are shown. In this configuration, it is possible to change the intensity of the backlight via the two arrow buttons. (9 and 10) -
Measurement preset selection: push the “MEASURE” button(7) to open the list. Scroll it with the arrow buttons (9 and 10) in order to select the preset corresponding to the enclosure to test. The display will show the name of the speaker in the first row and the name of each way in the second one, as is reported in the label attached to each outline speaker.
-
Measuring: push the “MEASURE” button(7).
You will hear a “click” and you will see the results of the test. For each way the resistance is measured and compared to the limits saved in the measurement preset. If the detected value is within the limits, the green LED of the corresponding way will light up, otherwise one of the two red LEDs will come up and the loudspeaker will have to be tested more thoroughly. In addition, the display will alternate the name of the way with the result of the test.
The display will show:
Ok: Value within the limits
OPC: Open Circuit
Los: Low Resistance
HiR: High Resistance -
Execution of a subsequent test: push again the “MEASURE” button(7).
-
Selection of a different preset: push the arrow buttons (9 and 10) in order to scroll the list and repeat step 3.
NOTE: via the “No One” preset you can measure the resistance of each way and the display will show the numerical values.
OVERALL DIMENSIONS
NOTES
Outline carries out ongoing research for product improvement. New
materials, manufacturing methods and design upgrades are introduced to
existing products without prior notice as a routine result of this philosophy.
For this reason, any current Outline product may differ in some aspect from
its description, but will always equal or exceed the original design
specifications unless otherwise stated.
© Outline 2021
Operating manual product code: Z OMFASTQC
Release: 20211015
Printed in Italy
OUTLINE S.R.L.
Via Leonardo da Vinci, 56
25020 Flero (Brescia) Italy
Tel.: +39 030.3581341
Fax +39 030.3580431
info@outline.it
www.outline.it
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>