outline KI-SP Series Powerful Flexible Speaker User Manual

outline KI-SP Series Powerful Flexible Speaker

SAFETY REGULATIONS

Please read this manual carefully and in its entirety. It contains important information regarding safety issues, including guidelines for general safe use of rigging systems as well as advisories on government regulations and liability laws. The suspension of large, heavy objects in public places is subject to numerous laws and regulations at the national/federal, state/provincial, and local levels. The user must assume the responsibility for making sure that the use of any rigging system and its components in any particular circumstance or venue conform to all applicable laws and regulations in force at the time.

GENERAL SAFETY RULES

• Carefully read this manual in all its parts
• Respect the working load limits and maximum configurations of the elements and of any third-party component (such as suspension points, motors, rigging accessories, etc…)
• Do not incorporate any accessory not provided by Outline; all damaged or defective components must be replaced only by equivalent parts approved by Outline
• Ensure personnel health and safety, ensure that no one is standing under the system during the installation, and ensure that all personnel involved in the installation are equipped with personal safety devices
• Always double-check that the elements are correctly connected before suspending the system.

DISPOSAL OF WASTE MATERIALS

Your product is designed and manufactured with high-quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the Euro-pean Directive 2012/19/EU and subsequent amendments. This means that the product must NOT be disposed of with other household-type waste. It is the users’ responsibility to dispose of their waste electrical and electronic equipment by handing it over to an approved reprocessor. For more information about where you can send your equipment for recycling, please contact your local distributor. The correct disposal of your old product will help prevent potential negative consequences for the environment and human health.

CONFORMITY AND WARRANTY

All the Outline electro-acoustic and electronic devices are in conformity with the provisions of EC/EU directives (as stated in  our CE declaration of conformity).  The CE declaration of conformity is attached to the product warranty certificate and is shipped with the product.

SERIES DESCRIPTION

Conceived and manufactured to give clients a flexible and easy-to-use product introduction to Outline, the new Ki series brings the engineering quality, distinctive lines and audio performance that have made the Italian brand an international reference point in sound reinforcement. Both Ki10 SP and Ki12 SP’s compact dimensions, audio performance and thoughtful design make them ideal solutions for a wide variety of permanently installed applications. Ki10 SP and Ki12 SP self-powered loudspeakers are equipped with 10” and 12” LF transducers respectively, both of which feature a 2.5” voice coil for high power and reliability. A 1.5” diaphragm compression driver provides the HF reproduction. The Outline-designed passive crossover networks fit-ted to both models also make them very efficient in terms of amplifier channels and external control.
Both products also feature another Outline first, a brand new design of the rotatable waveguide. Many comparable loudspeakers offer this facility but Out- line’s Ki-series are the first to allow the installer to quickly and easily rotate the entire horn and HF section without any disassembly of the loudspeaker. This piece of original engineering offers a real advantage in small rooms or those with low headroom, as the HF horn can be quickly adjusted to ensure the required dispersion (100° x 50° or 50° x 100°) regardless of the orientation of the cabinet.

OPERATION (ROTATABLE HORN)

It is possible to rotate the Ki’s horn without removing the front grille. Just unlock the four screws and spin the wheel using the two openings on the front of the speaker. Then retighten the screws to lock the horn in the new position. Please note that when the horn is in a vertical position it is shown through two dedicated red dots in the openings (one on each side as shown in the figure below).

OVERALL DIMENSIONS

KI10-SP OVERALL DIMENSIONS

KI10-SP OVERALL DIMENSIONS

RIGGING INSTRUCTIONS

This series offers many rigging possibilities: eighteen M8 points are available for multiple purposes. The loudspeaker can be rigged using the appropriate wall mount accessories (WME75 for Ki10, WHH100-B, TH100-B, and STAND-WALL1 for both). Outline recommends to always use a secondary safety device when the system are rigged. The loudspeaker can also be mounted directly on a 35 mm speaker stand.

AMPLIFICATION

The amplifiers are directly integrated into the cabinet. The amplifier module is completely autonomous and designed to be immediately ready for use (plug & play) once connected to the power. The integrated DSP allows the management of the input signal and control through the dedicated section available by connecting to the processor with a USB cable (type B). Before doing this connection, you need to download and install the ArmoníaPlus, amplifiers management software Below you will find the elements offered by the management panel:

PRESET
Outline has made available four presets that are potentially useful in any situation.On the rear panel there is a button for selecting one of the available presets. These presets are named according to the needs they were designed for:

• FLAT;
• BASS BOOST;
• LOUDNESS, for low volume listening;
• PRESENCE, for a speech application.

TECHNICAL SPECIFICATIONS KI10 SP

OUTLINE S.R.L.
Via Leonardo da Vinci, 56 25020 Flero (Brescia) Italy Tel.: +39 030.3581341 Fax +39 030.3580431 info@outline.it

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>