fujifilm sx800 Long Range Surveillance Camera Owner’s Manual

fujifilm sx800 Long Range Surveillance Camera

Safety Precautions

For Your Safety
This section lists important precautions that must be followed to ensure safe and correct use of the product. Read them before using the product and observe them during use.
The 4 WARNING and 4 CAUTION indications in this document indicate the following:

WARNINGS Failure to observe warnings could result in death or serious injury.
CAUTIONS Failure to observe cautions could result in injury or property damage.

WARNINGS

• Take all steps necessary to prevent water entering the product. Failure to observe this precaution could result in fi re or electric shock. Should water fi nd its way in, disconnect the power source immediately.
• Be sure the product is installed securely. Serious accidents could result should the product fall from a height.
• When working in high places, work with a partner or partners, use a safety line, and take all other precautions necessary to ensure safety. Slipping, falling, or loss of balance could result in serious accidents.
•  When installing the camera in high places, ensure that people below keep their distance. Falling objects could cause serious accidents.
• Ensure that the surface on which the camera is installed is level. Failure to observe this precaution could cause the camera to fall, potentially causing serious accidents.

CAUTIONS

• Keep the product out of direct sunlight.
•  Do not turn the product on without first confirming that the power supply is connected correctly.
• The product could cause injury if dropped during transport. Take all precautions necessary to ensure that the product is not dropped.
• Ensure that the voltage of the power supply matches the product’s rated voltage. Incorrect voltages could damage the product or result in fi re or electric shock.
• When connecting or disconnecting the power cable, hold the plug and not the cable. Damage to the cable could result in fi re or electric shock.
• Should you detect any abnormalities such as smoke, unusual noises or smells, or the presence of foreign matter inside the product, disconnect the power supply immediately and contact the original retailer.
• Do not disassemble or modify. Failure to observe this precaution could result in electric shock or product malfunction. Mal-functions or damage resulting from customers disassembling or modifying the product are not covered under warranty.
• Do not aim the camera at the sun. Direct sunlight focused through the lens could damage the product’s internal parts.
• Install the camera base down. Installing the camera in other orientations could lead to warping that may impair product performance.

GERNEL PERCUATIONS

• Use the product only as described in this manual.
• The camera and its accessories are precision devices. Under no circumstances should they be subjected to excessive force.
• Install the camera in a housing or other location where it will not be exposed to rain, wind, dust, or direct sunlight.
• Bringing the camera abruptly from a cold location to a warm and humid environment could cause the lens to fog. Take measures to allow the camera to adapt to the new environment before subjecting it to changes in temperature and humidity.
• Replace the cap if the camera will not be used for an extended period.
•  The camera lens has a special anti-reflective coating. As a result, the back of the lens may appear spotted, but this has no effect on performance.

NOTICES

Verification
Model Number: SX800
Trade Mark: Fujifi lm

FCC RULE

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Cautions:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Warning

To assure continued compliance, follow the attached installation instructions. This includes using the provided power cord and shielded interface cables when connecting to computer or peripheral devices. Also, any unauthorized changes or modifi cations to this equipment could void the user’s authority to operate this device.
For Cor Customers In Comers In Canada
CAN ICES-3(A)/NMB-3(A)
WARNING: This equipment is compliant with Class A of CISPR32. In a residential environment this equipment may cause radio interference.
This product complies with the following EU Directives:

• RoHS Directive 2011/65/EU
• EMC Directive 2014/30/EU

Compliance with these directives implies conformity to applicable harmonized European standards (European Norms) which are listed on the EU Declaration of Conformity issued by FUJIFILM Corporation for this product or product family.
This compliance is indicated by the following conformity marking placed on the product: This marking is valid for non-Telecom products and EU harmonized Telecom products (e.g. Bluetooth).
About the Icons
The symbols on the product represent the following:

| AC
---|---

| DC
| Class II equipment (The construction of the product is double-insulated.)

Disposal of Elecisposal of Electrical  and Electronic ionic Equipment in equipment in Private Households In the e Households In the European Union, Noropean Union, Norway,, Iceland and Liechel and Liechttenstenstein:

This symbol on the product, or in the manual and in the warranty, and/or on its packaging indicates that this product shall not be treated as household waste. Instead it should be taken to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

Precautions for Use

Operating Environment

• The camera can be used at temperatures of from −10 to +50 °C (temperatures below freezing are only supported if the power supply is not interrupted) and at humilities of from 10 to 80% (no condensation).
• Prolonged use at high temperatures or humilities could degrade components, shortening product life.
• Do not install the product where it will be exposed to solvents or other chemicals.

Installation

• Do not install LAN or audio cables in close proximity to cables for fluorescent lights or other electrical devices. Failure to observe this precaution could impair sound or image quality. Move the cables if signal quality is affected.
• Using the product in close proximity to powerful electromagnetic fields, such as those produced by television transmitter antennas, electric motors, or transformers, could result in distorted or wavy pictures. Should this occur, use steel cable shielding.
• Use a Category 5 or better shielded twisted pair (STP) LAN cable for LAN connections.
• Plastic cable insulation may sometimes be damaged by crows or other birds. Protect cables using a cable conduit.
• Fix cables in place so that they are not subject to repeated vibration, friction, or tugging. Failure to observe this precaution could cause the cable to break.
• Install the product base down.

Use

• Do not aim the lens directly at the sun or other bright light sources or reflections. Failure to observe this precaution could result in deterioration of the image sensor color filter, affecting picture color.
• Do not subject the product to strong physical shocks or vibration. Failure to observe this precaution could result in product malfunction.
• Clean the product with a soft, dry cloth. Never use chemically-treated cloths or solvents such as benzine (petroleum ether), thinner, or alcohol. Failure to observe this precaution could cause warping or discoloration.
• Do not apply force to the connectors when handling the product. Failure to observe this precaution could result in the product being disconnected or damaged.

Network Settings

• You will need to supply an IP address, subnet mask, and gateway IP address.
• The frame rate may drop if multiple streams are transmitted via unicast.
• When connected to multiple devices, the product will transmit data to all devices at the rate supported by the device with the slowest receiving rate.

Introduction

Parts of the Camera

The  Control panel

Installation and Connection

Installation

Use the screw holes on the base to secure the camera to a mount or other surface.

WARNING: Attach the product securely to a surface that can safely bear the combined weight of the camera and associated hard-ware. Do not mount the camera in unstable locations or locations subject to frequent vibration or attach it to weak materials such as drywall, ALC (autoclaved lightweight concrete), concrete blocks, or plywood. Injury could result should the product fall from its mounting.
CAUTIONS:

• Use ¼ ʺ, UNC 20 thread screws with a thread engagement length of 6.5 to 10 mm.
•  Install the camera base down

A handle can be attached using the screws on top of the camera.

CAUTIONS:

• Use M4 screws with a thread engagement length of at least 4 mm and a protrusion of no more than 6 mm.
• Do not use the screw holes on top of the camera for any other purpose.

Screw hole Specification:
The specifications for the screw holes on the top and base of the camera are as follows:

Connection Schematic

The schematic below illustrates how the camera can be installed for use in IP mode.

When the camera is connected to a computer in IP mode, camera settings can be adjusted using dedicated software. An ONVIF application can be used to view the live feed and control the camera.

Operating Mode Selection: DIP Switches

Use the DIP switches to select the operating mode.

Operating mode

| DIP switch
---|---
A| B| C| D
IP| OFF| ON| OFF| OFF
RS485| ON| OFF| OFF| OFF
Stand-alone| ON| ON| OFF| OFF

Connecting to a Computer

1. Connect the supplied plug to the power cable and plug the cable into the camera power connector.

2. Use an Ethernet cable to connect the camera to a computer.

3. Select IP mode by setting DIP switch B to “ON” and DIP switches A, C and to off

TIPS: For information on using remote-control mounts or ONVIF-compatible control units, see the documentation provided with the device.

Viewing and Recording the Live Feed

The camera’s live feed can be viewed and recorded using a web browser.

Launching a Web Browser

For information on using the web browser, see the browser’s online help. To connect to the SX800, you will need to assign it an appropriate IP address. The default IP address and subnet mask assigned to the camera at shipment are as follows:

1. Turn on the camera and computer.
2. Launch a web browser.
3. Enter the product IP address in the address bar (“http://[IP address]”).
4. Enter a user name and password. At shipment, the user name and password fields are blank.
5. Click OK.

TIPS:

• Enter a user name and password, both of which can be from 8 to 15 characters long. Take all steps necessary to protect the password.
• The camera must then be re-initialized in stand-alone mode as described below.
  • Note that this deletes all existing accounts.
  • A Turn the camera off .
  • B Select stand-alone mode using the DIP switches on the rear control panel (page 7).
  • C Turn the camera on.
  • D Press and hold the OK/MENU button on the rear control panel for 3 seconds to display the menus.
  • E Select IP ADDRESS SETTINGS RESET in the setup menu. F Turn the camera off and return to Step 3 of “Connecting to a Computer” (page 8).
  • Note: For more information, see the Owner’s Manual: Stand-Alone Mode.

Preferences

Adjust camera settings.

Choosing a category (A) displays the associated settings (B).

the camera clock and adjust other system-related settings.
PTZ SETTING| Adjust settings for remote-control mounts.
SYSTEM MAINTENANCE| Restart the camera, update camera firmware, and perform other forms of system maintenance.
SECURITY| Adjust network security settings.
NETWORK SETTING| Adjust basic network settings.
PORT| Choose ports for HTTP or RTSP.
VIDEO| Adjust video system and streaming settings.
DISPLAY/OSD SETTING| Adjust display settings.
言語 /LANG.| Choose a language for camera menus and displays.

CAUTION: Do not insert or remove memory cards while the camera is on. Failure to observe this precaution could corrupt image damage the memory card.

CAMERA SETTING

Adjust basic camera settings.

AF SETAF SETTINGTING

Choose how the camera focuses when autofocus is enabled via ONVIF.

Options

CONTINUOUS AF| QUICK AF| ONE PUSH A

FOCUS  AREA

Choose how the camera selects the focus area when CONTINUOUS AF is selected for AF SETTING .

selection.

AF SENSITIVITYY

Choose how long the focus system will continue to track the current subject after a new subject enters the focus area at a diff er-ent distance from the camera. The higher the value, the longer the camera will wait before switching subjects.

IRISIRIS

Choose the aperture value (iris). See “Specifications” (page 27) for supported values.

SHUTTER SPEEDTER

Choose the shutter speed.

minimum shutter speed.
MANUAL| Choose the shutter speed manually.

GAIN

Adjust image brightness.

lighting is poor.
HYPER- AGC| Choose for automatic gain control adapted to low light conditions.

DAY/NIGHT

In day/night mode, the camera records in color when the subject is brightly lit and in black-and-white when the subject is poorly lit. This option is available when OFF is selected for EXTERNAL TRIGGER.

AUTO

| The camera selects day or night mode automatically according to lighting conditions. You can choose the lighting conditions that trigger the switch when AUTO is selected:

• DAY to NIGHT THRESHOLD : Choose the brightness threshold that triggers the switch from day to night ( 0 – 255 ).
• NIGHT to DAY THRESHOLD : Choose the brightness threshold that triggers the switch from night to day ( 0 – 255 ).
• SWITCHING SENSITIVITY : Choose how long ( 0 – 60 S ) the camera waits to switch modes once the brightness threshold is crossed.

SCHEDULED

| The camera switches to day or night mode at a selected time.

• DAY START TIME : Choose a time from 00:00 to 23:59.
• NIGHT START TIME : Choose a time from 00:00 to 23:59.

AUTO & SCHEDULED

|

• Choose a light trigger and time for switching between day and night modes.
• DAY to NIGHT THRESHOLD : Choose the brightness threshold that triggers the switch from day to night ( 0 – 255 ).
• NIGHT to DAY THRESHOLD : Choose the brightness threshold that triggers the switch from night to day ( 0 – 255 ).
• SWITCHING SENSITIVITY : Choose how long ( 0 – 60 S ) the camera waits to switch modes once the brightness threshold is crossed.
• DAY START TIME : Choose a time from 00:00 to 23:59.
• NIGHT START TIME : Choose a time from 00:00 to 23:59.

DAY| The camera operates in day mode at all times.
NIGHT| The camera operates in night mode at all times.

EXTERNAL  TRIGGER

Choose whether day/night selection is performed in response to an external trigger.

trigger. The optical filters selected for day/night are disabled.
ON(CLEAR)| Replaces the filter with clear glass. The optical filters selected for day/night are disabled.
OFF| The camera does not respond to the external trigger.

IR WAVWLENGHT

Match the IR wavelength to the infrared light source used. See “Specifications” (page 27) for supported values.

IMAGE STABILIZABILIZAATION

Choose an image stabilization option adapted to the scene.

the scene.
OIS| Reduce the effects of camera shake using optical image stabilization.
EIS| Reduce the effects of camera shake using electronic image stabilization.
OFF| Image stabilization disabled.

Lighting Triggers

Day/night selection can be configured in any of the following three ways:

Configuration

|

Description

| Configured using
---|---|---
Menu item| Option

A Auto

|

Day/night selection is performed automatically according to a schedule and/or lighting conditions.

| CAMERA SETTING >
DAY/NIGHT| AUTO ,

SCHEDULED ,
or AUTO & **SCHEDULED**

B Manual| Day/night selection is performed manually.| DAY or NIGHT
C External trigger| Day/night selection is performed in response to input from an external trigger.| CAMERA SETTING >
EXTERNAL TRIGGER| ON(VLC) ,
ON(CLEAR) ,or OFF

The optical filters chosen for day/night do not apply if a signal is received from the external trigger when ON(VLC) or ON(CLEAR) is selected for EXTERNAL TRIGGER. If no signal is received or if OFF is selected, the optical filter will function as shown in the following table.

The following table shows relation between the filter selected for day/night, image color, and wavelength:

Option

|

Filter

|

Image color

| CONFIGURATION >

CAMERA SETTING > IR WAVELENGTH

---|---|---|---
Status| Supported wavelengths
DAY| IRC| Color| Disabled| Visible light only

808 nm only

VLC| Black and white
NIGHT| CLEAR| Enabled| 950 nm, 940 nm, 850 nm, 808 nm, visible light
VLC

IMAGE QUALITY SETTING

Adjust image quality settings.

OPTICAL FILTER (DAY)

Choose an optical filter for day mode.

visible-light footage.
VLC| Enable the VLC filter, blocking visible light and recording only infrared footage.

OPTICAL FILTER(NIGHT)

Choose an optical filter for night mode.

infrared footage.

WDR

Use with high-contrast subjects to reveal details “washed out” in the highlights and lost in the shadows. Choose higher values
for high-contrast subjects.

BACKLIGHT CORRECTION

Reduce loss of detail in the shadowed areas of backlit subjects. The higher the value, the greater the effect.

HEAT HAZE REDUCTION

Reduce the wavering effect of heat haze, making the image clearer overall. The higher the value, the greater the effect.

FOG REDUCTION

Make images where the subject is obscured by fog more vivid and easier to see. The higher the value, the greater the effect.

NOISE REDUCTION

Reduce the effects of noise for a smoother picture. The higher the value, the greater the effect.

DIGITAL ZOOM

Choose the zoom factor for digital zoom.

Options

OFF| 1.25×| 1.5×| 1.75×| 2×

USE SETTING

Choose a shooting preset.

shooting non-surveillance footage at social gatherings or other events.

BRIGHTNESS

Adjust brightness. The further the slider is to the right, the greater the effect.

CONTRAST

Adjust contrast. The further the slider is to the right, the greater the effect.

SATURATION

Adjust color saturation. The further the slider is to the right, the greater the effect.

SHARPNESS

Make outlines more or less sharply defined. The further the slider is to the right, the greater the effect.

WHITE BALANCE

Match white balance to the light source (for example, sunlight or artificial lighting).

level.
CUSTOM 1/CUSTOM 2| Measure a value for white balance using a piece of paper or other white reference object.
FINE| For subjects lit by direct sunlight.
SHADE| For subjects in the shade or under overcast skies.
COLOR TEMPERATURE| Choose a color temperature ( 3000K , 5000K , or 9000K ).

TIP: After choosing an option for white balance, you can adjust white balance shift.

SYSTEM

View the firmware version and other information. You can also set the camera clock and adjust other system-related settings.

MODEL NAME

View the camera model name.

SERIAL NO.

View the product serial number.

FW VER.

View the camera firmware version.

APPLICATION VER.

View the application version.

TIME ZONE

Choose a time zone.

NTP SERVER ADDRESS

Enter the IP address for the NTP (Network Time Protocol) server.

PORT NUMBER

Choose the NTP server port.

CHECKING INTERVAL

Choose how often the camera checks the NTP server port.

PRIORITY OF TIME SETTING

Choose whether the time display matches the camera’s internal clock (DEVICE) or the time reported by the NTP server (NTP).

clock.
NTP| The display shows the time reported by the NTP server.

IN-CAMERA TIME SETTING

Set the camera clock.

ABOUT DEVICE

View OSS information.

PTZ SETTING

Adjust settings for remote-control mounts.

TIP You will need to turn the camera off and then on again after adjusting settings in this menu.

RS485 BAUD RATE

Choose the baud rate for data transmitted via RS485.

Options

115200bps| 38400bps| 19200bps| 9600bps| 4800bps| 2400bps

RS485 ID

Choose the RS485 ID (1–31).

RS485 TERMINATION

Select ON to enable the RS485 termination resistor.

PTZ POSITION INQUIRY

Choose whether the camera queries remote-control mounts for pan and tilt positions.

CAUTION Select ON when using the camera with remote-control mounts that support position queries.

Pelco-P/Pelco-D

Choose a communications protocol.

PELCO CMD INTERVAL

Choose the interval at which the camera sends Pelco commands to remote-control mounts (10–300 msec).

SYSTEM MAINTENANCE

Restart the camera, update camera firmware, and perform other forms of system maintenance.

REBOOT

Select OK to restart the camera.

RESET SETTINGS

Select OK to restore camera settings to their default values. Items in the following menus are not aff ected:

NETWORK SETTING

IMPORT CONFIGURATION FILE
Import settings from a camera settings fi le. Click BROWSE and choose a settings fi le created using EXPORT TO CONFIGURATION FILE.

EXPORT TO CONFIGURATION FILE

Export camera settings. Click OK to download the settings folder.

FW UPDATE

Update the camera firmware. Click BROWSE and select the fi le containing the new firmware version to begin the update.

COPY LOG DATA

Save a copy of camera logs. Click BROWSE, choose a destination, and click OK to save the logs.

CHANGE PASSWORD

Change the camera login password.

SECURITY

Adjust network security settings.

RTSP AUTHENTICATION

Choose an RTSP authentication method (DISABLE, BASIC, or DIGEST).

RTSP AUTHENTICATION ALGORITHM

Choose an algorithm for DIGEST authentication (MD5 or SHA256).

HTTP AUTHENTICATION

Choose an HTTP authentication method (BASIC or DIGEST).
TIP The MD5 authentication algorithm is used for HTTP. Users wishing to switch to SHA256 can do so via CGI commands. This service
can be requested from your retailer.

NETWORK SETTING

Adjust basic network settings.

IPv4 ADDRESS

Enter the camera’s IPv4 address.

IPv4 SUBNET MASK

Enter the camera’s IPv4 subnet mask.

IPv4 DEFAULT GATEWAY

Enter the camera’s default IPv4 gateway.

MAC ADDRESS

View the camera’s MAC address.

IPv4 MTU

Choose the maximum volume of data that can be transmitted per packet (frame).

PRIORITY DNS SERVER

Enter the IP address of the primary DNS server.

SECONDARY DNS SERVER

Enter the IP address of the secondary DNS server.

IPv4 ADDRESS

Choose how the camera’s IPv4 address is assigned.

Dynamic Host Configuration Protocol (DHCP).

PORT

Adjust port settings.

HTTP PORT

Choose the HTTP port.

RTSP PORT

Choose the RTSP port.

VIDEO

Adjust video settings.

VIDEO SYSTEM

Choose the standard (NTSC (60 Hz) or PAL (50 Hz)) used for video output from the camera.

VIDEO FORMAT

Choose the frame size for video shot using the camera.

ASPECT FOR VIDEO

Choose how video is displayed on monitors with an aspect ratio that does not match the selected format.

black bars above and below.
SQUEEZE| Video with an aspect ratio of 16∶9 is reformatted to fit displays with a 4∶3 aspect ratio.

BIT RATE

Choose whether streaming video is encoded at a FIXED or VARIABLE bit rate. Note that this option is available only when H.264
encoding is selected.

VIDEO QUALITY

Choose the output quality for streaming video (HIGH, STANDARD, or LOW). Note that this option is available only when H.264
encoding is selected.

FRAME RATE

Choose the frame rate for streaming video from values between 1 and 30 fps.

ENCODING

Choose an encoding for streaming video.

I FRAME INTERVAL

Choose the I-Frame interval for streaming video.

DISPLAY/OSD SETTING

Adjust display settings.

DATE DISPLAY

Select ON to show the date in the live feed.

TIME DISPLAY

Choose whether times are displayed using a 12- or 24-hour clock.

DATE DISPLAY FORMAT

Choose the order in which the year, month, and day are displayed.

LANG

Choose a language for camera menus and displays.

Troubleshooting

Should the product fail to function as expected, consult the table below. If you are unable to fi nd a solution here, contact your local Fujifi lm distributor.

No video, or the image in the video is dark.

|

• The camera is off : Check that the cables are correctly connected, the power lamp is lit, and the
• correct voltage is being supplied to the lens.
• The cables are not correctly connected : Check that the cables are correctly connected.
• The lens cap is on : Remove the lens cap.
• The iris is stopped down to the minimum aperture : Select maximum aperture.
• Shutter speed requires adjustment : Select an appropriate value for shutter speed.

The image in the video is “washed out”.|

• Camera white balance, gain, shutter speed, or other settings require adjustment : Confirm that settings are adjusted appropriately.
• Aperture requires adjustment : Adjust aperture appropriately.

The image in the video is out of focus.
Spots appear in the video.|

• The lens is dirty : Clean the lens.

Defaults

Selecting OK for SYSTEM MAINTENANCE > RESET SETTINGS restores settings to the following default values:

CAMERA SETTING

DAY/NIGHT

| AUTO

• DAY to NIGHT THRESHOLD : 70
• NIGHT to DAY THRESHOLD : 130
• SWITCHING SENSITIVITY : 7 S

EXTERNAL TRIGGER| OFF
IR WAVELENGTH| VISIBLE LIGHT
IMAGE STABILIZATION| AUTO

IMAGE QUALITY SETTING

Option| Default|
---|---|---
OPTICAL FILTER(DAY)| IRC| ****

NETWORK SETTING

OPTICAL FILTER(NIGHT)| CLEAR
WDR| OFF
BACKLIGHT CORRECTION| OFF
HEAT HAZE REDUCTION| OFF
FOG REDUCTION| OFF
NOISE REDUCTION| 2| Option| Default
DIGITAL ZOOM| OFF                                  IPv4 ADDRESS| 192.168.1.10
USE SETTING| SURVEILLANCE                 IPv4 SUBNET MASK| 255.255.255.0
BRIGHTNESS| 50                                    IPv4 DEFAULT GATEWAY| 192.168.1.254
CONTRAST| 50                                    MAC ADDRESS| —
SATURATION| 50                                    IPv4 MTU| 1500
SHARPNESS| 70                                    PRIORITY DNS SERVER| 192.168.1.254
WHITE BALANCE| AUTO| SECONDARY DNS SERVER| —
IPv4 ADDRESS| MANUAL

SYSTEM

Option| Default|
---|---|---
MODEL NAME| —| Option| Default
SERIAL NO.| —                                     DATE DISPLAY| ON
FW VER.| —                                     TIME DISPLAY| 24H
APPLICATION VER.| —| DATE DISPLAY FORMAT| MM-DD-YYYY
TIME ZONE| —| 言語 /LANG
IN-CAMERA TIME SETTING| —
ABOUT DEVICE|

PTZ SETTING

SYSTEM MAINTENANCE

SECURITY

Specifications

Minimum object distance

(M.O.D.) *****

| 10 m “at focal lengths of 20–400 mm”
20 m “at focal lengths of 401–800 mm”
Image sensor| CMOS sensor
Video|

• File format : MOV
• Video compression : H.264 compliant

Frame size| 1920 × 1080, 1280 × 720, 640 × 480 (NTSC), 768 × 576 (PAL)
Metering| Average
Focus modes| Continuous AF, quick AF, MF
Aperture selection| Auto, f/4–f/16
Shutter speed| Auto (with minimum speed selection of  s)
Gain adjustment| Manual (ISO 400 – ISO 819200), AGC, HYPER AGC
Day/night selection| AUTO, SCHEDULED, AUTO & SCHEDULED, DAY, NIGHT
Wavelengths| VISIBLE LIGHT, 950 nm, 940 nm, 850 nm, 808 nm
Image stabilization| Available (AUTO, OIS, EIS, OFF)
Wide dynamic range| Selectable (2 levels)
Back light compensation| Selectable (2 levels)
Heat haze reduction| Selectable (3 levels)
Fog reduction| Selectable (3 levels)
Noise reduction| Selectable (3 levels)
Shooting Mode Preset| SURVEILLANCE, MOVIE PRODUCTION
Brightness| Selectable (100 levels)
Contrast| Selectable (100 levels)
Saturation| Selectable (100 levels)
Sharpening| Selectable (100 levels)
White balance| AUTO, AUTO WHITE PRIORITY, CUSTOM 1, CUSTOM 2, FINE, SHADE, COLOR TEMPERATURE (choose a color temperature in degrees Kelvin from 3000K, 5000K, and 9000K)
Image output connectors| HDMI, HD-SDI, composite (BNC)
Audio input/output|

• Input impedance : 40K Ω
• Output impedance : 200 Ω

Video output|

• NTSC : 1080p, 720p, 480p
• PAL : 1080p, 720p, 576p

External interface| 100BASE-T, RS-485, external trigger (DAY/NIGHT)
Baud rate| 152000 bps, 38400 bps, 19200 bps, 9600 bps, 4800 bps, 2400 bps
Internet protocol| ONVIF (port number 8080) HTTP, RTSP
RS-485 protocol| Pelco D, P (includes custom commands)
Power source| DC 12 V
Power consumption| 9.5 W
Dimensions (W × H × D)| 156 mm × 139 mm × 410 mm/6.14 in. × 5.47 in. × 16.14 in.
Weight| Approx. 6.4 kg/14.11 lb
Operating environment|

• Temperature : −10 °C – +50 °C/+14 °F – +122 °F
• Humidity : 10% – 80% (no condensation)

Tilt limit|

• From the foremost part of the forward lens.

http://www.fujifilm.com

References

• Fujifilm [Global]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>