Rebel RB-1065 Industrial Vacuum Cleaner User Manual
- June 5, 2024
- Rebel
Table of Contents
Rebel RB-1065 Industrial Vacuum Cleaner
SAFETY INSTRUCTIONS
In order to reduce the injuries or damages, follow basic safety precautions applied when using any electrical device, including the following:
- Read the entire instruction manual before you start installation and assembly and keep it for future reference.. Keep the manual for future reference.
- Before connecting the device to power supply socket, make sure the voltage indicated on the device corresponds to the voltage in the power supply socket.
- Do not start vacuuming if the dust bag or filters are not installed in the vacuum cleaner, as this may damage the device.
- Do not place any objects in ventilation slots.
- Do not obstruct ventilation by covering ventilation openings.
- Prior to each use, check if the hose, nozzles or tube are not blocked. If so, remove the object or dust before vacuuming.
- If the hose, nozzle or tube become blocked while vacuuming, turn off the device and remove blocked item and then turn on the device.
- Clean this device in accordance to instructions listed in Cleaning section.
- ALWAYS turn off the device and disconnect it from the mains supply:
- if it’s not operating correctly,
- if there’s an uncommon voice when using,
- before disassembling the device,
- before cleaning,
- when not in use.
- When you disconnect the power cord of the device, grasp and pull the plug, not the cord/cable.
- Fixed power cable may only be replaced in an authorized service point.
- Turn off the device by pressing power on button before disconnecting the power cord.
- Keep the device out of the reach of children. Only adult persons should use the vacuum cleaner.
- Keep the device and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
- Do not carry the vacuum cleaner by the cord or hose.
- Do not pull the cord over sharp edges and do not slam in by the door.
- Make sure the plug does not bump into people, animals or objects when winding the cord.
- Do not step on the hose or crush it.
- Do not place the appliance in water or any liquid, do not use it with wet hands.
- Be careful when vacuuming stairs and make sure the device is below the user.
- When vacuuming, always keep your head, other body parts, hair and clothing away from the device.
- Do not point hose or tube at people or animals.
- Do not use the vacuum to clean animals or people.
- Do not vacuum:
- big objects with sharp edges; it may block and damage the device.
- harmful and corrosive liquids or flammable and explosive substances as this may cause fire;
- hot or glowing substances.
- Do not use the product for purpose different from displayed in this operating manual.
- Do not use the appliance unattended when it’s working.
- Producer of this product is not responsible for damages caused by inappropriate handling and using of the device.
- Do not use this device if the cord or the plug is damaged, or the appliance is broken.
- Do not attempt to repair this device yourself. Only authorized and qualified personnel may repair this device. Never disassemble this device.
- Use only authorized accessories.
- Do not use the device near explosives. During vacuuming the device produces sparks which may cause ignition.
- Do not expose the device to rain or moisture. Water entering a motor will increase the risk of electric shock.
- During work, use personal protection equipment. Always wear safety eye protection when using this vacuum cleaner.
- After working with the device, roll up the power cord and place it on the hook, which is located on the air outlet.
Technical data
| Power | 1400 W |
|---|---|
| Power supply | 230 V; 50 Hz |
| Operation radius | 8 m |
| Cable length | 5,4 m |
| Hose length | 1,5 m |
| Suction inlet | 41 mm |
| Weight | 5 kg |
| Sound pressure level | <90 dB |
| Airflow | 30 l/s |
| Vacuum (max) | 18 kPa |
| Dust bin capacity | 15 l |
| Air inlet filter | HEPA |
| Air outlet filter | Foam cover |
| Dust bag type | Textile or paper |
In set
| Textile dust bag, plastic tube, elastic hose, crevice nozzle, water brush, 2-step floor nozzle, user’s manual
OPERATING
Note:
Before installing or removing accessories from the device, make sure to unplug
it from power mains. Before first use, turn the vacuum cleaner upside down and
install the supplied wheels, inserting them in the holes intended for it.
Dry vacuum cleaning
- The use of a textile bag is recommended for dry vacuuming.
- Remove the upper part of the vacuum cleaner by unlocking the latches on the sides of the appliance.
- Dust bag should be attached on air inlet inside dust binr
- Place the upper part with motor on the lower part and lock the latches
- Place the end of the hose in air inlet. The correct connection will occur when the hose latch engages in the appropriate hole on the top of the air inlet.
- Connect both parts of the tube.
- Connect the end of the hose with the tube.
- Install selected nozzle on the other end of the tube.
- Insert the end of the power cord into an electrical outlet
- To turn on device, press the power button.
- The level of the dust bag full depends on the type of dust being drawn in
- If the bag is overfilled, it may burst, so it is recommended to check the level of its filling.
Wet vacuum cleaning
- In the case of wet vacuuming, the same operations as for dry vacuuming are performed in the same way
- Do not use dust bag for wet vacuuming. The collected liquid should go directly to the container
- The HEPA filter housing has a movable element – a float, whose task is to protect the engine from flooding. If the level of sucked liquid exceeds a certain maximum value, the float will be sucked into the fan inlet, closing the outflow of air from the container and protecting the engine from water ingress. The suction power on the suction hose will drop completely – switch off the vacuum cleaner immediately and empty the container.
Note:
If any part of the vacuum cleaner (hose, tube, nozzle) is blocked, immediately
turn off the device and remove the source of clogging. Only after doing this
you can return to vacuuming.
Blowing
- Place the end of the hose in air outlet. The correct connection will occur when the hose latch engages in the appropriate hole on the top of the air outlet.
- Install selected nozzle on the other end of the tube (to achieve the strongest possible air flow, it is recommended to use a crevice nozzle).
Cleaning and maintenance
- Before cleaning, make sure the device is switched off and disconnected from the power supply.
- The dust container can be washed under running water, but it should be thoroughly dried before reuse. Clean the upper part of the vacuum cleaner a slightly damp cloth.
- If the device is working louder than usual or the suction power dropped significantly, check the suction hose and tube for blockage. If they become clogged, remove the object blocking the airflow with a thin long object.
Note:
Working with clogged suction accessories can lead to engine failure.
Replacement and maintenance of the HEPA filter
-
Remove the upper part of the vacuum cleaner by unlocking the latches on the sides of the appliance.
-
To remove filter:
- unscrew and remove the round part under the filter
- slide the filter towards the previously unscrewed element
-
Filter should be washed under running water.
Note:
Do not use detergent or washing accessories to wash the filter. After washing, set the filter to dry (do not squeeze) -
The filter can be mounted to the vacuum cleaner only after it has completely dried.
-
If the filter is damaged, e.g. during cleaning, replace it with a new one.
Dust bag change
- Remove the upper part of the vacuum cleaner by unlocking the latches on the sides of the appliance.
- Remove the dust bag from the air inlet.
- The full dust bag should be disposed of in a suitable dustbin – it cannot be reused.
Storage
- Store the device in vertical position.
- Store the device in a dry place.
- Dust container should be dry before putting the device away.
- There is a catch on the vacuum cleaner housing, which is used to attach the suction tube to the vacuum cleaner.
CE DECLARATION OF CONFORMITY
Supplier’s name: Lechpol Electronics Sp. z o.o., Sp.k.
Supplier’s address: ul. Garwolińska 1, 08-400 Miętne, Poland
Equipment type
Industrial vacuum cleaner
Model: RB-1065
We, the undersigned, hereby declare that the equipment specified above
confirms to the following directives:
-
EMC
EN 55014-1:2006+A1:2009+A2:2011,
EN 55014-2:2015
EN 61000-3-2:2014,
EN 61000-3-3:2013 -
LVD 2014/35/EU
EN 60335-2-2:2010 +A11:2012+A1:2013
EN 60335-1:2012+A11:2014+A13:2017
EN 62233:2008 -
ROHS 2011/65/EU and 2015/863/EU
EN 62321-1:2013
EN 62321-2:2014, EN 62321-3-1:2014, EN 32321-4:2014, EN62321-5:2014
EN62321-6:2015, EN62321-7-1:2015
EN 62321-7-2:2017, EN 62321-8:2017
Supplier: Lechpol Electronics Sp. z o.o., Sp.k.
Representative’s name: Piotr Wojdat
Place and date of issue: Garwolin, Poland; 14.04.2020