Volonic VALET 3 FreePower Wireless Charging Pad User Manual
- June 5, 2024
- Volonic
Table of Contents
Volonic VALET 3 FreePower Wireless Charging Pad
OVERVIEW
Product overview
- Charging surface (gray surface in image)
- USB-C input port
- LED indicators
- Rubber legs
Specification
- Dimensions: 23 x 13.5 x 1.45cm (9.05 x 5.32 x .57in)
- Weight: 692grams (1.5lbs)
In The Box
- Volcanic Valet 3
- Volonic 36W USB-C PD wall charger
- Volonic 6FT (1.8m) USB-C to USB-C cable
- Authenticity / registration card
LED characteristics
• LED on solid – Device detected and charging
• LED blinking – Unidentified object detected on charging surface, remove the
device and try again
• All 3 LED’s blinking – Contact our support team at
concierge@volonic.com or 1-833-VOLO-100
How to use
- Remove the gift box from the sleeve
- Open gift box to unveil your beautiful Volonic Valet 3.
- Under your Valet 3 is an envelope with your Authenticity card and unique serial number
- To register your device, scan the QR code on the back of your authenticity card tray
- Enter the last 6 digits of the serial number
- Remove authenticity card tray to access provided wall charger and cable
- Plug USB-C wall charger into your power outlet.
- Attached USB-C cable into wall charger, make sure a ”click” sound is heard
- Plug the other end of the USB-C cable into your Valet 3, and make sure a “click” is heard
- All 3 LED’s on your Valet 3 should cycle on, then off
- Now enjoy the freedom of being able to wirelessly charge your device anywhere on the top surface.
For frequently asked questions, please visit https://volonic.com/pages/faqs
If additional assistance is needed, please reach out to our support team at
concierge@volonic.com or 1-833-VOLO-100
PRODUCT CARE
Housing
- To clean use a soft cloth (cotton or microfiber) and gently wipe clean
- Spray glass cleaner onto soft cloth (cotton or microfiber) and gently wipe
- Do NOT spray directly on to product
- Do NOT use ammonia or bleach-based cleaners
Top plate
Alcantara®
- It is sufficient to dust Alcantara® using a soft brush, a dry cloth, a lint roller, or a vacuum cleaner.
- After having dusted Alcantara®, run a slightly moistened white cotton cloth over it. Avoid the use of printed absorbent cloths/papers as they can release ink onto the material.
- For stains; act immediately (within 30 minutes) and begin treating the stain from the outside edge into the center in order to avoid the stain spreading
- Never apply a cleaning product directly onto Alcantara®
- For liquids, use non-printed absorbent paper or a sponge
- Avoid rubbing to prevent the stain from spreading or going deep into the material
- Use a white cloth or a well-wrung sponge for the removal of the stains; if you use a sponge, rinse it in clean water and wring it well between each wipe.
Leather
- To clean use a lightly damp soft cloth (cotton or microfiber) and wipe clean
- For a deeper clean
- mix a solution of warm water and dish soap
- Dip a portion of a soft cloth into the solution, wring the cloth to remove excess water, and wipe the surface.
- Use a second clean damp cloth with only warm water to wipe soap off
- Dry surface by using a dry towel and dabbing
- Do NOT use ammonia or bleach-based cleaners
Warning
- Keep liquids away from product and ports
- Do not disassemble your Valet 3
If you have any questions or concerns contact our support team at concierge@volonic.com or 1-833-VOLO
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>