ZALMAN X3 ATX Mid Tower Computer

Precautions

• Read this manual carefully before installing.
• Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
• Wear gloves to prevent accidents when installing the product.
• Severe damage may occur when mounting the system, so do not apply excessive force.
• Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
• Be careful not to block the ventilation hole of the product when using the system.
• Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
• Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
• Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
• Store and use the product out of children’s reach.
• Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
•  The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

Fan Support

| Top| 2 x 120mm, 2 x 140mm
Front| 3 x 120mm, 2 x 140mm
Rear| 1 x 120mm, 1 x 140mm

Pre-Installed Fan(s)

| Front| 3 x 120mm (with Addressable RGB LED Sync)
Rear| 1 x 120mm (with Addressable RGB LED Sync)

Radiator Support

| Front| 120mm / 240mm / 280mm / 360mm
Rear| 120mm
I/O Ports| 2 x USB 3.0, 2 x USB 2.0, 1 x Headphone Jack, 1 x Microphone Jack, LED Control Button, Reset Button, Power Button

Caution (Radiator support)

280mm radiator can be problematic to install on the X3. Width of the radiator should be 140mm. If you wish to use a radiator larger than 140mm please be sure to check the distance between the side of the radiator to screw hole. If the distance is below 5.7mm you can install it to X3.

Accessories

I/O Ports

| Part| #| Part| #| Part| #| Part

---|---|---|---|---|---|---|---
ⓐ| USB 3.0 Port| ⓑ| USB 2.0 Port| ⓒ| Microphone Jack| ⓓ| LED Control Button
ⓔ| Headphone Jack| ⓕ| USB 2.0 Port| ⓖ| USB 3.0 Port| ⓗ| Power Button

RGB(Addressable) LED Control Button

1. Short Press : 1st ~ 50th RGB LED Lighting Mode (Effects & Colors)
2. Long Press : RGB LED Lighting Mode Change (LED Control Button → Motherboard Sync (Addressable Sync) → Lighting Off)

Removing the side panels

Mounting the motherboard

Motherboard size

Mounting the PSU

Mounting the PCI-E(VGA) card

Graphics card holder

Install the graphics card brace to a convenient position.

Mounting the 3.5″ and 2.5″ SSD / HDD

Mounting the 2.5” SSD / HDD

Mounting the front radiator

Caution
280mm radiator can be problematic to install on the X3. Width of the radiator should be 140mm. If you wish to use a radiator larger than 140mm please be sure to check the distance between the side of the radiator to screw hole. If the distance is below 5.7mm you can install it to X3.

RGB LED Controller

Fan Specifications

• RFD 120A [ X3 ]
• Dimensions : 120 x 124 x 25 mm Bearing Type : Hydraulic Bearing
• Fan – Rating Voltage : 6~13.8 V DC
  • Rating Current : 150mA ±20%LED – Rating Voltage : 4.5~5.3 V DC
  • Rating Current : 800mA ±20%Fan Speed : 800~1,500 ±10% RPM Max Airflow : 34.34 CFM
• Max Noise Level : 25.6 dB(A) ±10%Connector : 3-Pin, 3-Pin Addressable Weight : 160g
• Life Span : 40,000 hrs
• Cable Length : 580mm x 2

I/O Connectors

www.zalman.com

References

• zalman.com
• ANDPRO.RU - интернет магазин компьютерной и офисной техники с выгодными ценами и доставкой

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>