SHARP QW-DX41F47EI-EN Dishwasher User Manual

SHARP QW-DX41F47EI-EN Dishwasher

SAFETY INSTRUCTIONS

General Safety Warnings

• Read these instructions carefully before using your appliance and keep this manual for future reference. Please check the packaging of your machine before installation and the outer surface of the machine once the packaging has been removed. Do not operate the machine if it appears damaged or if the packaging has been opened.
• Packaging materials protect your machine from any damage that might occur during transportation. The packaging materials are environmentally friendly as they are recyclable. Use of recycled material reduces raw material consumption and decreases waste production.
• This appliance can be used by children aged from 8 years and above, and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of theappliance in a safe way and understand hazards involved. Children should not be allowed to play with the appliance.
• Remove packaging and keep it out of reach of children.
• Keep children away from detergents and rinse aids.
• There may be some residue left in the machine after washing. Keep children away from the machine when it is open.

Installation Warnings

• Choose a suitable and safe place to install your machine.
• Only original spare parts should be used with the machine. Unplug the machine before installation. Check that the indoor electrical fuse system is connected in line with safety regulations. All electrical connections must match the values on the plate.
• Ensure the machine does not stand on the electrical supply cable.
• Never use an extension cord or a multiple socket connection.
• The plug should be accessible after the machine is installed.
• After installation, run your machine unloaded for the first time.
• The machine must not be plugged in during positioning.
• Always use the coated plug supplied with your machine.
• If the electrical cable is damaged, it should only be replaced by a qualified electrician.
• Connect the hose directly to the water inlet tap. The
• pressure supplied by the tap should be a minimum of 0.03 MPa and a maximum of 1 MPa. If the pressure exceeds 1 MPa, a pressure relief valve
  must be fitted between the connection.

During Usage

• This machine is for domestic use only; do not use
• it for other purposes. Commercial use will void the guarantee.
• Do not stand, sit or place loads on the open door of the dishwasher.
• Only use detergents and rinse aids produced specifically for dishwashers. Our company is not responsible for any damage that may occur due to misuse.
• Do not drink water from the machine.
• Due to the danger of explosion, do not place any chemical dissolving agents into the machine’s washing section.
• Check the heat resistance of plastic items before washing them in the machine.
• Only put items in the machine which are suitable for dishwashing, and take care not to overfill the baskets.
• Do not open the door while the machine is in operation, hot water may spill out. Safety devices ensure the machine stops if the door is opened. The machine door should not be left open. It maycause accidents.
• Place knives and other sharp objects in the cutlery basket in a blade-down position. For models with the automatic door-opening system, when the EnergySave option is active, the door will open at
• the end of a program. To prevent damage to your dishwasher, do not attempt to close

RECYCLING

• Some machine components and packaging consist of recyclable materials.
• Plastics are marked with the international abbreviations:(>PE<, >PP<, etc. )
• The cardboard parts consist of recycled paper. They can be put into waste paper containers for recycling.
• Material unsuitable for domestic waste must be disposed of at recycling centres.
• Contact a relevant recycling centre to obtain information about disposal of different materials.

PACKAGING AND THE ENVIRONMENT

• Packaging materials protect your machine from damage that may occur during transportation. The packaging materials are environmentally friendly as they are recyclable. The use of recycled material reduces raw material consumption and therefore decreases waste production.

CE Declaration of Conformity
We declare that our products meet the applicable European Directives, Decisions and Regulations and the requirements listed in the standards referenced.

Disposal of your old machine
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead, it shall be handed over tothe applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and humanhealth, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where the product was purchased.

INSTALLATION

Machine positioning
When positioning the machine, place it inan area where dishes can be easily loaded and unloaded. Do not put the machine in an area where the ambient temperature falls below 0°C.
Read all warnings located on the packaging before removing the packaging and positioning the machine. Place the machine close to a water tap and drain. Take into consideration that the connections will not be altered once the machine is in position. Do not hold the machine by its door or panel. Leave an adequate distance around the machine to allow ease of movement when cleaning.
Ensure the water inlet and outlet hoses are not squeezed or trappedand that the machine does not stand on the electrical cable while positioning.
Adjust the feet so the machine is level andbalanced. The machine should be placed on flat ground otherwise it will be unstable and the door of the machine will not close properly.

Water connection
We recommend fitting a filter to your water inlet supply in order to prevent damage to \your machine due to contamination (sand,rust, etc.) from indoor plumbing. This will also help prevent yellowing and deposit formation after washing.Note printing on the water inlet hose! If models are marked with 25°, the water temperature may be max. 25 °C (coldwater).
For all other models: Cold water preferred; hot water max. temperature 60 °C.

Water inlet hose

WARNING: Use the new water inlet hose supplied with your machine, do not use an old machine’s hose.
WARNING: Run water through the new hose before connecting.
WARNING: Connect the hose directly to the water inlet tap. The pressure supplied by the tap should be a minimum of 0.03 MPa and a maximum of 1 MPa. If the pressure exceeds 1 MPa, a pressure relief valve must be fitted between the connection.
WARNING: After the connections are made, turn the tap on fully and check for water leaks. Always turn off the water inlet tap after a wash program has finished.

An Aquastop water spout is available with some models. Do not damage it or allow it to become kinked or twisted.

Electrical connection

WARNING: Your machine is set to operate at 220-240 V. If the mains voltage supply to your machine is 110 V, connect a transformer of 110/220 V and 3000 W between the electrical connection.
Connect the product to a grounded outlet protected by a fuse complying with the values in the “Technical Specifications” table”.
The earthed plug of the machine must be connected to an earthed outlet supplied by suitable voltage and current. In the absence of earthing installation, an authorised electrician should carry out an  earthing installation. In the case of use without earthing installed, we will not be responsible for any loss of use that may occur. The plug on this appliance may incorporate 13A fuse depending on the target country. (For Example UK, Saudi Arabia)

Fitting the machine under counter

If you wish to fit your machine under-counter, there must be sufficient space to do so and the wiring-plumbing must be suitable to do so (1). If the space under the countertop is suitable for fitting your machine, remove the worktop as shown in the illustration (2).
WARNING: The countertop, of which the machine will be placed under, must be stable in order to prevent imbalance. The top panel of the dishwasher must be removed to fit the machine under the countertop. To remove the top panel, remove the screws that hold it on, located at the rear of the machine. Then, push the panel 1 cm from the front towards the rear and lift it. Adjust the machine feet according to the slope of the floor (3). Fit your machine by pushing it under the counter taking care not to crush or bend the hoses (4).
WARNING: After removing the top panel of your dishwasher, the machine should be placed in a space of the dimensions shown in the figure below.

| A| B
---|---|---
All Products| B1| B2
Product’s Height (±2 mm)|

820 mm

|

830 mm

|

835 mm

A: If there is no felt on the top of the product; you should take into account this product’s height.
B1 : If there is felt on the top of the product with 2nd basket; you should take into account this product’s height.
B2 : If there is felt on the top of the product with 3rd basket; you should take into account this product’s height.

TECHNICAL SPECIFICATIONS

General appearance

1. Worktop
2. Upper basket with racks
3. Upper spray arm
4. Lower basket
5. Lower spray arm
6. Filters
7. Rating plate
8. Control panel
9. Detergent and rinse-aid dispenser
10. Cutlery basket
11. Salt dispenser
12. Upper basket track latch
13. Super Active Drying Unit: This system provides better drying performance your dishes.

Technical specifications

850(mm)

598(mm)

598(mm)

Net weight| 46 (kg)
Operating voltage / frequency| 220-240V

50 (Hz)

Total current| 10(A)
Total power| 1900(W)

Water supply pressure

| Maximum: 1 (Mpa) Minimum:

0.03 (Mpa)

 BEFORE USING THE APPLIANCE

Preparing your dishwasher for first use

• Make sure the electricity and supplywater specifications match the values indicated in the installation instructions for the machine.
• Remove all packaging material inside the machine.
• Set the water softener level.
• Fill the rinse aid compartment.

4.2 Salt Usage
For a good washing function, the dishwasher needs soft, i.e. less calcareous water. Otherwise, white lime residues will remain on the dishes and the interior equipment. This will negatively affect your machine’s washing, drying and shining performance. When water flows through the softener system, the ions forming the hardness are removed from the water and the water reaches the softness required to obtain the best washing result. Depending on the level of hardness of the inflowing water, these ionsthat harden the water accumulate rapidly inside the softener system. Therefore, the softener system has to be refreshed so that it operates with the same performance also during the next wash. For this purpose, dishwasher salt is used. Your machine should only use special dishwasher salt to soften the water. Do not use any small grained or powdered type of salts which are easily soluble.Using any other type of salt can damage your machine.
4.3 Fill the salt
To add softener salt, open the salt compartment cap by turning it counter clockwise. (1) (2) At first use, fill the compartment with 1 kg salt and water (3) until it is almost overflowing. If available, using a funnel (4) will make filling easier. Replace the cap and close it. After every20-30 Cycles add salt into your machine until it fills up (approx. 1 kg).

Only add water to the salt compartment on first use.
Use softener salt specifically produced for use in dishwashers. When you start your dishwasher, the saltcompartment is filled with water, therefore put the softener salt in prior to starting your machine. If the softener salt has overflowed and you do not start the machine immediately, runa short washing program to protect your machine against corrosion.

Test Strip

NOTE: The level is set to 3 as default. If the water is well water or has a hardness level above 90 dF, we recommend that you use filter and refinement devices.

Water Hardness Table

Level

| ****

German dH

| ****

French dF

| ****

British dE

| ****

Indicator

---|---|---|---|---
1| 0-5| 0-9| 0-6| L1 is shown on the display.
2| 6-11| 10-20| 7-14| L2 is shown on the display.
3| 12-17| 21-30| 15-21| L3 is shown on the display.
4| 18-22| 31-40| 22-28| L4 is shown on the display.
5| 23-34| 41-60| 29-42| L5 is shown on the display.
6| 35-50| 61-90| 43-63| L6 is shown on the display.

Water Softener System
The dishwasher is equipped with a water softener which reduces the hardness in the mains water supply. To find out the hardness level of your tap water, contact your water company or use a test strip (if available).
Setting
In order to change the salt level, follow the below steps:

• Open the door of the machine.
• Turn on the machine, and press the Program button as soon as the machine turned on.
• Hold down the Program button until “SL” disappears.
• The machine will display the last setting.
• Set the level by pressing the Program button.
• Turn off the machine to save the setting.

Detergent Use
Only use detergents specifically designed for domestic dishwashers. Keep your detergents in cool, dry places out of reach of children. Add the proper detergent for the selected program to ensure the best performance. The amount of detergent needed depends on the cycle, load size, and soil level of the dishes. Do not overfill the detergent compartment. Otherwise you can see whitish streaks or bluish layers on glass and dishes whichmay cause glass corrosion. Continued over-use of detergent may cause machinedamage. Using too little detergent can result in poor cleaning and you may see whitish hard water. See the detergent manufacturer’s instructions for further information.

Filling with Detergent
Push the latch to open the dispenser and pour in the detergent. Close the lid and press it until it locks inplace. The dispenser should be refilled just before the start of each program. If the dishes are heavily soiled, place additionaldetergent in the pre-wash detergent chamber.

Using Combined Detergents
These products should be used according to the manufacturer’s instructions. Never put combined detergents into the interior section or the cutlery basket. Combined detergents contain not only the detergent but also rinse-aid, salt replacement substances and additional components depending on the combination. We recommend you do not use combined detergents in the short program. Pleaseusepowder detergents in such a program. If you encounter problems when using combined detergents, please contact the detergent manufacturer. When you stop using combined detergents, make sure that water hardness and rinse aid settings are set to the correct level.

Rinse-Aid Use
Rinse aid helps to dry the dishes without streaks and stains. Rinse-aid is required for stain-free utensils and clear glasses. The rinse aid is automatically released during the hot rinse phase. If an insufficient amount of rinse aid is used, whitish stains may be left on the dishes and drying and washing performance will be impaired.If too much rinse aid is used you may seebluish layers on glass and dishes.

Filling the Rinse-aid and Setting
To fill the rinse aid compartment, open the rinse-aid compartment cap. Fill the compartment with rinse aid to the max level and then close the cap. Be careful not to overfill the rinse aid compartment and wipe up any spills. In order to change the rinse aid level, follow the below steps before turning onthe machine:

• Open the door of the machine.
• Turn on the machine, and press the Program button as soon as themachine is turned on.
• Hold down the program button until “rA” disappears. Rinse aid setting follows water hardness setting.
• The machine will display the last setting.
• Change the level by pressing the Program button.
• Turn off the machine to save the setting.

The factory setting is “4”.If the dishes are not drying properly or are spotted, increase the level. If blue stains form on your dishes, decrease the level.

LOADING YOUR DISHWASHER

For best results, follow these loading guidelines.
Loading the household dishwasher up to the capacity indicated by the manufacturer will contribute to energy and water savings.
Manual pre-rinsing of tableware items leads to increased water and energy consumption and is not recommended You can place cups, glasses, stemware, small plates, bowls, etc. in upper basket. Do not lean long glasses against one another or they cannot remain steady and may be damaged. When placing long stem glasses and goblets, lean them against the basket edge or rack and not against other items. Place all containers such as cups, glasses and pots into the dishwasher with the opening facing downwards otherwise water can collect on items. If there is a cutlery basket in your machine, you are recommended to use the cutlery grid in order to obtain the best result. Place all large (pots, pans, lids, plates, bowls etc.) and very dirty items in the lower rack. Dishes and cutlery should not be placed above each other.
WARNING: Take care not to obstruct the rotation of spray arms.
WARNING: Make sure after loading the dishes do not prevent opening of the detergent dispenser.

Recommendations
Remove any coarse residue on dishes before placing the dishes in the machine. Start the machine with a full load.  Do not overload the drawers or place dishes in the wrong basket.
WARNING: To avoid any possible injuries, place long-handle and sharp- pointed knives with their sharp points facing down or horizontally on the baskets.

Upper Basket Height adjustment
Turn the Rail Stop Clips, at the ends of the rails, to the sides to open them (as shown in the image below), then pull out and remove the basket. Change the position of the wheels, then reinstall the basket to the rail, making sure to close the Rail Stop Clips. When the upper basket is in the higher position, large items such as pans can be placed on the lower basket. 

Height Adjustable Rack (peg type)
The height adjustable racks enable glasses and cups to be placed on or under the racks. The racks can be adjusted to 2 different heights. Cutlery and utensils can also be placed on the racks horizontally.

Height Adjustable Rack (peg type)
The foldable racks in the upper basket enable the placement of large items such as pots and pans. Each section can be folded separately. The foldable racks can be either raised up or folded down.

Lower Basket Two Folding Racks
The folding racks on the lower basket allow for the placement of larger items, such as pots and pans. Each section can be folded separately. They can either be folded down or raised up, as shown in the images below.

Alternative basket loads Lower basket

Upper basket

Incorrect Loads
Incorrect loading can cause poor washing and drying performance. Please follow the guidelines to get the best washing performance.  Unsuitable items for dishwashing

• Cigarette ashes, candle leftovers, polish, paint, chemical substances, iron-alloy materials.
• Forks, spoons and knives with wooden, bone, ivory or nacre coated handles; glued items, items soiled with abrasive, acidic or base chemicals. Temperature-sensitive plastics, copper or tincoated containers.
• Aluminium and silver objects.
• Some delicate glasses, ornamental printed porcelains; some crystal items, adhered cutlery, lead crystal glasses, cutting boards, synthetic fibred items.
• Absorbent items such as sponges or kitchen rugs.

IMPORTANT: In future, purchase dishwasher-proof kitchenware.

Important Note for Test Laboratories
For detailed information required for tests according to EN normative and a softcopy of the manual, please send the model name and serial number to the following address: dishwasher@standardtest.info

PROGRAM TABLE

| P1| P2| P3| P4| P5| P6| P7| P8| P9
---|---|---|---|---|---|---|---|---|---
Program Name:| Eco| Auto

60°C – 70°C

| Auto

50°C – 60°C

| Auto

30°C – 50°C

| Express

50’ 65°C

| Everyday 60°C| Delicate 40°C| Quick 30’ 40°C| Prewash

Type of Soil:

| ****

Standard program for normally soiled daily using dishes with reduced energy

and water consumptions.

| ****

Auto program for heavily soiled dishes.

| ****

Auto program for normally soiled dishes.

| ****

Auto program for normally soiled delicate dishes.

| ****

Suitable for normally soiled daily dishes

with faster program.

| ****

Suitable for normally soiled daily dishes.

| ****

Suitable for lightly soiled delicate dishes.

| ****

Suitable for lightly soiled dishes and quick wash.

| ****

Suitable to rinse dishes that you plan to wash later.

Level of Soil:| Medium| Heavy| Medium| Medium| Medium| Medium| Light| Light| Light
Amount of Detergent:

A: 25 cm3

B: 15 cm3”

| ****

A

| ****

A

| ****

A

| ****

A

| ****

A

| ****

A

| ****

A

| ****

A

|
Program Duration (h:min)| ****

03:42

| ****

01:37 – 02:58

| ****

01:29 – 02:01

| ****

01:09 – 01:32

| ****

00:50

| ****

01:34

| ****

01:14

| ****

00:30

| ****

00:15

Electiricity consumption (kWh/cycle)| ****

0.937

| ****

1.300-2.000

| ****

1.100 – 1.300

| ****

0.700 – 0.900

| ****

1.000

| ****

1.320

| ****

0.800

| ****

0.670

| ****

0.020

Water consumption (l/cycle)| ****

9.0

| ****

11.8 – 24.0

| ****

10.9 – 18.5

| ****

10.6 – 17.7

| ****

9.5

| ****

14.4

| ****

13.9

| ****

10.9

| ****

4.2

• The program duration may change according to the amount of dishes, the water temperature, the ambient temperature and selected additional functions.
• Values given for program other than the eco program are indicative only
• If your model has a turbidity sensor, it has an Auto program instead of an Intensive program.
• The Eco program is suitable for cleaning normally soiled tableware and is the most efficient program in terms of combined energy and water use. It is used to assess compliance with EU ecodesign legislation.
• Washing tableware in a household dishwasher usually consumes less energy and water than hand dishwashing, when used according to the manufacturer’s instructions.
• Only use powder detergent for short programs.
• Short programs do not include drying.
• To assist drying, we recommend slightly opening the door after a cycle is complete.
• You can access the product database where the model information is stored by reading the QR code on the energy label.
  NOTE: According to regulations 1016/2010 and 1059/2010, Eco program energy consumption values may differ. This table is in line with regulations 2019/2022 and 2017/2022.

THE CONTROL PANEL

1. On/Off button

2. Program Selection Button

3. Display

4. Half Load Button

5. Upper Basket Half Load Led

6. LowerBasket Half Load Led

7. Delay Button

8. Options Button

9. Extra Hygiene Led

10. Extra Dry Led

11. Salt Indicator

12. Rinse Aid Indicator

13. On/Off Button
    Switch the machine on by pressing the On/ Off button. When the machine is on, “–“will be shown on the Display (3).

14. Program Selection Button
    Select a suitable program by pressing the Program Selection button. The program will start automatically when the door is closed.

15. Display
    The Display shows the number and total time of the selected program alternately and the remaining time during operation.

16. Half Load Button
    Press the Half Load button to select the area of the dishwasher containing dishes to be washed. You can select both baskets(i,ii), the upper basket only (i), or the lower basket only (ii). Press the button until thelight corresponding to the basket containing the dishes to be washed illuminates. Dishes in other areas will not be washed. Ifa program is incompatible with the Half Load function, a buzzer will sound.

17. Delay Button
    Press the Delay button to delay the start time of the selected program for 1 hour up to 19 hours. Pressing the button once delays the start time for 1 hour, and continuing to press will increase the delaytime. Press the Delay button to change or cancel the delayed start time. If you switch off the machine while the delay timer isactive, the delayed time is cancelled.

18. Options Button
    Press the Options button once to activate the Extra Hygiene option. When you activate it, the Extra Hygiene led (iii) will illuminate so the washing temperature and duration changes on the selected program,and it ensures a more hygienic wash. Press the Options button twice to activatethe Extra Dry option. When you activate it, Extra Dry led (iv) will illuminate and so extraheating/drying steps will be added to the selected program. Press the button a third time to deactivate the functions, both lights will switch off.If an extra feature has been used on the most recent wash program, this feature will remain active on the next selected program. To cancel this feature on the newly selected wash program, press the feature button untilthe light on the button switches off.
    NOTE: If you decide not to start the selected Program, please see the “Changing a Program” and “Cancelling aProgram” sections.
    NOTE: When there is insufficient softening salt, the Salt Lack Warning Indicator (v) will illuminate to indicate thesalt chamber needs filling.
    NOTE: When there is insufficient rinse aid, the Rinse Aid Lack Warning Indicator (vi) will illuminate to indicate the rinse aid chamber needs filling.

Changing a Program
Follow the steps below to change a program while in operation. NOTE: Open the door slightly at first to stop a program before it is complete in order to avoid water spillage.

Cancelling a Program
Follow the steps below to cancel a program while in operation. Switching the Machine Off

automatically after 15 minutes, if no buttons are pressed.
NOTE: Do not open the door before a program has finished.
NOTE: Leave the door slightly open at the end of a wash program to speed up drying.
NOTE: If the door of the machine is opened or the power is cut during operation, the program will continue when the door is closed or the power returns.
Buzzer Sound Control
To change the buzzer sound level, follow the below steps:

1. Open the door and press Delay (5) And Options (6) buttons simultaneously for 3 seconds.
2. When the sound setting is confirmed, the buzzer gives a long sound and themachine will display the last set level, from “S0” to “S3”.
3. To decrease the sound level press the Delay button (5). To increase the sound level, press the Options button (6).
4. To save the selected sound level, turn off the machine.’’S0’’ level means all voices the are off. Factory setting is “S3”.

Save Power Mode
To activate or deactivate Save Power Mode, follow the below steps:

1. Open the door and press the Half Load (4) and Delay (5) buttons simultaneously for 3 seconds.
2. After 3 seconds, the machine will display the last Setting, “IL1” or “IL0”.
3. When Save Power Mode is activated, “IL1” will be displayed. On In this mode, interior lights will turn off 4 minutes after thedoor is opened, and the machine will turn off after 15 minutes of no activity in order to save energy.
4. When Save Power Mode is deactivated “IL0” will be displayed. If Save Power Mode is de-activated, interior lights will be on as long as the door is open, and the machine will always be on unless it is turned off byuser.
5. To save the selected setting, turn off the machine.
   In factory setting, Save Power Mode is active

Natural Ion Tech
This function provides extra hygiene tothe machine thanks to Ion Technology. Natural Ion Tech function is activated by pressing the Half Load (4) button for 3 seconds. Meanwhile the display will count from 1 to 3. At the end of 3 seconds, “Ion”will be displayed which indicates the Ionizer function is activated. The button is released after “Ion” is displayed. If no intervention bythe user, 24 hours after activation of the Ionizer function, it is automatically cancelled.
NOTE:

• If the machine is turned off, the Ionizer function is cancelled.
•  Natural Ion Tech function does not work with any program.
•  If the Ionizer function is active, ionizer led lights up like dimming during door is open.

CLEANING AND MAINTENANCE

Cleaning your dishwasher is important to maintain the machine’s service life. Make sure that the water softening setting is set correctly and the correct amount of detergent is used to prevent limescale accumulation. Refill the salt compartment when the salt sensor light comes on. Oil and limescale may build up in your Dishwasher over time. If this occurs:
• Fill the detergent compartment but do not load any dishes. Select a program which runs at a high temperature and run the Dishwasher empty. If this does not clean your Dishwasher sufficiently, use a cleaning agent designed for use with dishwashers.
• To extend the life of your dishwasher, clean the appliance regularly each month
• Wipe the door seals regularly with a damp cloth to remove any accumulated residue or foreign objects.

Filters
Clean the filters and spray arms at least once a week. If any food waste remains or foreign objects on the coarse and fine filters, remove them and clean them thoroughly with water.

1. Micro Filter
2. Coarse
3. Metal Filter

To remove and clean the filter combination, turn it counter clockwise and remove it by lifting it upwards

1. Pull the coarse filter outof the micro filter
2. Then pull and remove the metal filter
3. Rinse the filter with lots of water until it is free of residue. Reassemble the filters. Replace the filter insert, and rotate it clockwise
   • Never use your dishwasher without a filter.
   • Incorrect fitting of the filter will reduce the washing effectiveness.
   • Clean filters are necessary for proper running of the machine.

Spray arms
Make sure that the spray holes are not clogged and that no food waste or foreign object is stuck to the spray arms. If there is any clogging,remove the spray arms and clean them under water. To remove theupper spray arm undo the nut holding it in position by turning it clockwise and pulling it downwards. Make sure that the nut is properly tightened when refitting the upper spray arm.

Drain Pump
Large food residues or foreign objects
which were not captured by the filters may
block the waste water pump. The rinsing
water will then be above the filter.
Warning Risk of Injury!
When cleaning the waste water pump, ensure that you do not injure yourself on pieces of broken glass or pointed implements.

In this case:

1. First always disconnect the appliance from the power supply.
2. Take out baskets.
3. Remove the filters.
4. Scoop out water, use a sponge if required.
5. heck the area and remove any foreign objects.
6. Install filters.
7. Re-insert baskets

TROUBLESHOOTING

TROUBLE CODE

| ****

POSSIBLE FAULT

| ****

WHAT TO DO

---|---|---

FF

| ****

Water inlet system failure

| Make sure the water inlet tap is open and water is flowing.

Separate the inlet hose from the tap and clean the filter of the hose.

Contact for service if the error continues.

F5

| Pressure system failure| ****

Contact for service.

F3

| ****

Continuous water input

| ****

Close the tap and contact for service.

F2

| ****

Inability to discharge water

| Water discharge hose and filters may be clogged.
Cancel the program.
If the error continues, contact for service.
F8| Heater error| Contact for service.

F1

| ****

Overflow

| Unplug the machine and close the tap.
Contact for service.
FE| Faulty electronic card| Contact for service.
F7| Overheating| Contact for service.
F9| Divisor position error| Contact for service.
F6| Faulty heater sensor| Contact for service.
HI| High voltage failure| Contact for service.
LO| Low voltage failure| Contact for service.

The installation and repairing procedures should always carried out by the Authorised Service Agent in order to avoid possible risks. The manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons. Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used.
Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. Contact information for your customer service can be found on the back of this document. Function-relevant genuine spare parts according to the corresponding Ecodesign order can be obtained from Customer Service for a period of at least 10 years from the date on which your appliance was placed on the market within the European Economic Area.

FAULT

|

POSSIBLE CAUSE

|

TROUBLESHOOTING

---|---|---

Whitish stains remains on dishes.

|

Not enough detergent used.

|

Use the correct amount of detergent, as instructed in the program table.

Rinse aid dosage and/or water softener setting set too low.

|

Increase rinse aid and/or water softener level.

High water hardness level.| Increase water softerner level and add salt.

Salt compartment cap not closed properly.

|

Check that the salt compartment cap is closed properly.

Dishes do not dry.

| Drying option is not selected.| Select a program with a drying option.
Rinse aid dosage set too low.| Increase rinse aid dosage setting.

Rust stains form on the dishes.

|

Stainless-steel quality of the dishes is insufficient.

|

Use only dishwasher-proof sets.

High level of salt in wash water.

|

Adjust the water hardness level using water hardness table.

Salt compartment cap not closed properly.

|

Check that the salt compartment cap is closed properly.

Too much salt spilled in the Dishwasher while filling it with salt.

|

Use funnel while filling salt to the compartment to avoid spillage.

A poor mains grounding.| Consult a qualified electrician immediately.

Detergent remains in the detergent compartment.

|

Detergent was added when the detergent compartment was wet.

|

Make sure detergent compartment is dry before use.

References

• sharphomeappliances.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>