DRI-EAZ CC-02-003-0015 Velo Pro Low Profile Airmover Owner’s Manual

: June 5, 2024
: DRI-EAZ

Table of Contents

Safety Instruction
BEFORE YOU BEGIN
Parts Identification
Operating Positions
OPERATING INSTRUCTIONS$
TRANSPORT AND STORAGE
MAINTENANCE
Disassembly
Pro model
SPECIFICATIONS
Customer Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DRI-EAZ CC-02-003-0015 Velo Pro Low Profile Airmover Owner’s Manual

Safety Instruction

WARNING! To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.

WARNING! Unit must be grounded. Do not use with an extension cord. Connect only to an outlet provided with a ground fault interrupting device.

WARNING! Never operate a unit with a damaged power cord, as this may lead to electrical or fire hazards. If power cord is damaged, it must be replaced by a cord of the same type and amperage rating.

WARNING! Do not touch grills when unit is operating.

WARNING! Do not allow children to play with or around the unit. Be sure the unit is inaccessible to children when not attended.

WARNING! Always operate the unit on a stable, level surface so it cannot fall and cause injury.

WARNING! Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.

WARNING! Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area to avoid creating a trip hazard.

NOTICE: Keep motor dry. For indoor use only.
NOTICE: Unplug when not in use or when moving unit.
NOTICE: Do not alter or modify your Velo in any way. Use only replacement parts authorized by Legend Brands, Inc. Modifications or use of unapproved parts could create a hazard and will void your warranty. Contact your authorized Dri-Eaz distributor for assistance.

BEFORE YOU BEGIN

Warranty registration
Please visit warranty.legendbrandsrestoration.com to register your purchase. If you determine service isrequired, have your equipment model, serial number and original proof of purchase available and call your distributor for assistance with obtaining a return material authorization (RMA)

Parts Identification

Fig. A

Product overview

Operating Positions

Fig. B:

OPERATING INSTRUCTIONS$

Note that the Velo can be placed in a variety of positions for drying and air circulation. See Fig. B for details.

Unwrap the cord and plug the unit into a standard 115V GFCI-protected outlet.
CAUTION: Be sure switch is in the off position before connecting unit to power outlet.
Direct the Velo outlet toward the surface to be dried.
TIP: On the Velo Pro (F505), the airflow may be adjusted by pressing the Up or Down arrow on the speed control (Fig. D). A digital readout shows the approximate amp draw. Use this value to maximize the number of Velos you can place on a single circuit.
When surface is dry to the touch, switch the unit off and reposition the unit in the next area to be dried.
When finished, unplug the unit and re-wrap the cord in the cord wrap

For additional instructions about the use of airmovers for restorative drying, see Tech Tips under Resources on www.LegendBrandsRestoration.com.

Electrical safety devices

Circuit breaker : If the circuit breaker detects overload or short circuit conditions, the breaker will automatically shut off the electrical supply. If this occurs, check the power cable carefully for any damage and ensure it is plugged into a properly grounded outlet. Press the Circuit Breaker Reset Switch (Fig. A) to reestablish the electrical supply.

Ground Fault Circuit Interrupter : If the GFCI device detects a ground fault, it will automatically shut off the electrical supply. If this should occur, check the power cable carefully for damage and ensure it is plugged into a properly grounded outlet. Press the GFCI reset button (Fig. A) to reestablish the electrical supply.

TRANSPORT AND STORAGE

Always use the handle to load or carry the unit.
Wrap cord in either direction under front Cord Wrap tab and rear bottom edge (Fig. A). Pull cord snug and secure with plug clip.
Units may be stacked for transport and storage.
When transporting in a vehicle, secure the unit(s) carefully to prevent sliding and damage to the unit and/or injury to vehicle occupants.
Keep unit dry. Do not expose the unit to rain or snow.

MAINTENANCE

WARNING: Unplug unit before performing any maintenance.

Before each use
Inspect the power cord. If cord is damaged, do not use.
Always grasp the plug (not the cord) to unplug.

As needed
The exterior may be cleaned with a mild solution of detergent. Ensure housing is completely dry before use.
To clean interior, see Fig. C for instructions.

Disassembly

To disassemble for cleaning:

Lay the unit on its top (upside down). Remove the 4 blower bolts from the bottom of the unit
Turn the unit right side up and remove the 14 screws around the perimeter of the top housing and electrical enclosure.
Open the electrical box and feed the blower cord back through the opening to create slack inside the housing.
Lift the top housing shell and electrical enclosure together and flip them over next to the base to expose the inside of the housing.
Lift the blower out for full access to the inside of the housing.
Reverse the steps for reassembly.
IMPORTANT: Be sure to pull any slack blower cord back into the electrical enclosure before the lid is placed on the electrical enclosure.

Fig. C

Disassembly instruction

Pro model

Fig. D

Variable speed control with amp and total unit hours display

FOR SERVICE CALL YOUR LOCAL DISTRIBUTOR or the Legend Brands Service Department at 800-932-3030.

Be sure to visit warranty.legendbrandsrestoration.com to register your purchase. Your registration will help us provide you with updated product information as needed.

WARNING: This product and other substances that may become airborne from its use contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to P65Warnings.ca.gov

SPECIFICATIONS

Model	Velo (F504)	Velo Pro (F505)
Weight	18.6 lbs. 18.4 kg	18.6 lbs. 18.4 kg
Dimensions (D x W x H)	24 x 18 x 9 in.

61 x 45.7 x 22.9 cm

| 24 x 18 x 9 in.

61 x 45.7 x 22.9 cm

Amp draw| 1.9 amps (115V)| 1.2-1.9 amps (115V)
Velos per

15 amp circuit

| Up to 6| Up to 10
Power| 185W| 185W
Air movement| 885 CFM 1 1504 CMH| 500-885 CFM 850-1504 CMH
Static pressure| 1.65 in. (H2O)| 1.65 in. (H2O)
Sound level (avg.)| 69 dB| 69 dB
Control| On/Off switch| On/Off switch with variable speed
---|---|---
Cord length| 18 ft. | 5.5 m| 18 ft. | 5.5 m
Fan| 6 blades| 6 blades
Construction| Injection molded housing; steel wire inlet and outlet grills.| Injection molded housing; steel wire inlet and outlet grills
Safety| ETL tested to UL and CSA standards| ETL tested to UL and CSA standards

Specifications are subject to change without notice. Some values may be approximate.

Customer Service

15180 Josh Wilson Road, Burlington, WA 98233, USA

Phone: +1 800-932-3030
Fax: +1 360-757-7950
Website: LegendBrandsRestoration.com

The Velo Airmover uses a patented housing design to produce concentrated, broad-path airflow to accelerate the evaporation of moisture from materials for drying.

Patents: http://www.LBpatents.com