BN-LINK BND-60/U97A Short Period Repeat Cycle Timer User Manual
- June 5, 2024
- BN-LINK
Table of Contents
BN-LINK BND-60/U97A Short Period Repeat Cycle Timer
PRODUCTS VIEW
- Light Sensor: Functions during the day or during the night.
- Output indicator: Light illuminates when there is power output in the socket.
- ON time selecting knob: To set the “ON” duration for the equipment.
- OFF time selecting knob: To set the “OFF” duration for the equipment.
- Socket: Only intended to be used with a grounded device.
RATING
- Supply voltage: 125V-60Hz
- Max. loading: 15A/1875W Resistive
- 15A/1875W Tungsten, 15A/1875W Ballast, 1 HP, TV-5
- Operating temperature: 5F-122F(-15°C-50°C)
- Storage temperature: -4F-140°F(-20°C-60°C) Protection class: IP20
WARNING
- Electrical shock hazard
- Use a grounded outlet
- Follow local electrical codes
- For indoor use only
- Keep children away
- Unplug the timer before cleaning
- Fully insert plug
- Do not use it in wet locations
- Do not exceed the electrical rating
APPLICATIONS
- Co2 systems
- Heating systems
- Humidifiers
- Cooling systems
- Indoor sprinklers
- Aquariums
- Ventilators
- Nebulizers
- Hydroponic pumps
DANGER
To reduce the risk of electric shock, this product has a grounding-type plug
that has a third (grounding) pin. This plug will only fit into a grounding-
type power outlet. If the plug does not fit into the outlet, contact a
qualified electrician to install the proper outlet. Do not change the plug in
any way.
BRIEF INTRODUCTION
MAIN FEATURES
- With Day/Night Sensor
- ON—5 seconds to 30 minutes
- OFF—5 seconds to 60 minutes
- Functions during the day, during the night, or 24 daily
HOW TO INSTALL
Set ON/OFF Duration ON
- ON Time: Duration for which equipment will run.
- OFF Time: Duration in between ON times.
For example
If a device is required to run for 15 minutes and stop for 20 minutes, tum the
ON time dial till the white line aligns the 15-minute mark and tum the OFF
time dial till the white line aligns the 20-minute mark.
Plug into 125VAC outlet
For example
Use with irrigation pump (or other loads)
OPTIONAL SETTINGS
Change To 24-hour Control
- Set both values to minimum
- Plug in then set both values to maximum within 5 seconds
- Output light turns on or off according to the actual setting
Change To Day Control
- Set both values to maximum
- Plug in, then the set-top value to minimum followed by button value to a minimum within 5 seconds
- Output light turns on or off according to the actual setting
Change To Night Control
- Set both values to maximum
- Plug in, then set botton value to minimum followed by the top value to a minimum within 5 seconds
- Output light turns on or off according to the actual setting
TROUBLESHOOTING
PROBLEM:
The timer does not work during the day.
POSSIBLE CAUSES AND SOLUTIONS
- The timer is set to Night Control mode. Please switch to Night Control mode.
- Please remove dust or other obstacles from the light sensor located in the upper left corner.
- The on a timer is too short and the off-time is too long. Please check the dials.
- PROBLEM: limer does not work.
POSSIBLE CAUSES AND SOLUTIONS:
Check the power supply to the timer.
PROBLEM: limer does not work at night.
POSSIBLE CAUSES AND SOLUTION
- limer is set to Day Control mode. Please make sure the timer is in Night Control mode.
- Please make sure the front of the timer is not exposed to light.
- The on time is too short and the off-time is too long. Please check the dials.
PROBLEM: limer works day and night in Day Control mode.
POSSIBLE CAUSES AND SOLUTION
- limer is set to 24-hour Control mode. Please make sure the timer is in Night Control mode.
- Please make sure the timer is located with sufficient light in the day.
- Please remove dust or other obstacles from the light sensor located in the upper left corner
PROBLEM:
The ON time is too long or too short.
POSSIBLE CAUSES AND SOLUTIONS
Please turn the dial next to the previous scale
PROBLEM: The timer does not work properly: it turns on and then turns off in a short moment.
POSSIBLE CAUSES AND SOLUTIONS
- Please make sure the front of the timer is not exposed to light.
- Please make sure the light controlled by the timer will not light up the front of the timer
BN-LINK INC
- 12991 Leffingwell Avenue, Santa Fe Springs
- Customer Service Assistance: 1.909.592.1881
- E-mail: support@bn-link.com
- Http://www.bn-link.com
- Hours: 9 AM – 5 PM PST, Mon – Fri
- Designed in California and Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>