CLIPSTER 18459 Kerbl CuttoX Cordless Clipper Instructions

: June 3, 2024
: CLIPSTER

Table of Contents

CLIPSTER 18459 Kerbl CuttoX Cordless Clipper
Safety
Charging
Scope of delivery
Operation, cleaning and care
Troubleshooting
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CLIPSTER 18459 Kerbl CuttoX Cordless Clipper

CLIPSTER-18459-Kerbl-CuttoX-Cordless-Clipper-PRO

Safety

Please read the instructions for use carefully before operating the clippers, especially the „Safety“ section. This will help you avoid possible hazards and protect against damage to the device due to misuse. Keep the instructions for use handy for future reference. If the device is passed on to a new owner, please also hand over these instructions for use.

Explanation of terms and symbols
The following terms are used in these instructions for use:

If disregarded, can lead to serious injuries or death
DANGER: If disregarded, can lead to serious injuries (or death)
WARNING: Note Information that should be observed when handling the device. Danger of an electric shock! The device may never be charged or operated while in the bath, shower, over a filled washbasin / another container.

Intended use

the clippers are used to trim hair/fur
the device is designed for indoor use only. It should not be operated outdoors (garden, terrace, etc.).
if the device is used in a manner that does not comply with the intended use and/or if modifications are made to the device, then this voids the manufacturer‘s warranty and liabilities

Important danger warnings

keep the device, charging tray and connecting cable away from moisture, water and other liquids, and do not operate it with wet hands
do not immerse the device, charging tray and connecting cable under water or rinse off under running water
if the device should fall into water, it may not be used again afterwards
the integration of a residual-current-operated protective device, with a nominal tripping current of less than 30 mA, in the building installation provides additional protection. We recommend that you have your electrician install residual current protection for your power circuits.
the device must be disconnected from the power supply when the battery is charged or after at least 8 hours of pure charging time
if the battery does not fully charge after 8 hours, do not operate the device and contact the manufacturer

General safety instructions

Never operate the device if:

the device, charging tray or connecting cable is damaged
the clipping head is damaged or chipped because this can injure the skin
the device is dropped, shows visible damage or its functionality is impaired
the device is damaged so that electrical components are exposed In each case, the device must be disconnected from the mains immediately!

This device can be used by children 8 years of age and older and by individuals with impaired physical, sensory or mental abilities or those with insufficient experience and knowledge to do so, if they are being supervised or have been trained on the safe use of the device and understand the underlying hazards. Children may not play with the device. Cleaning and user maintenance may not be performed by children without supervision.

children should be supervised at all times to ensure that they do not play with the device. Make sure that children do not injure themselves on the clipping head. Keep the device out of the reach of children.
also keep the packaging material, e.g. films, away from children
lay the connecting cable in such a way so that no one can trip over or step on it
protect the connecting cable from damage. Never pull on the connecting cable. Always remove the cable from the power outlet by grasping the power pack plug. Keep the cable away from hot surfaces. Check the connecting cable for damage on a regular basis.
never expose the device to temperatures under 0 °C or over +40 °C for long periods of time. Avoid direct sunlight.
repairs may only be performed by authorised personnel in order to avoid a hazard
disconnect the device from the power supply for maintenance and parts replacement
the clipping head may not be taken apart

Safety during operation

you put the device down, e.g. to charge it or when you interrupt the cutting process for a brief period
you attach or remove the comb attachment
you clean or oil the device

Only use the clipper together with original accessories (charging tray, comb attachment, etc.). Never use sharp objects (e.g. a tail comb) to remove dust or foreign objects from the interior of the device

Charging

when the device is delivered, it is not yet ready for operation
before connecting the clipper to an outlet, make sure that the mains voltage matches the voltage listed on the nameplate of the power pack
in order to maintain the charge capacity of the battery, we recommend that you occasionally discharge the battery by operating the device until the motor stops
please charge the device for a full 8 hours before first use so that the included rechargeable battery is activated
please do not charge the device in temperatures under 0 °C or higher than 40 °C
please do not charge the device while exposed to direct sunlight or the heat of a radiator
the standard charge time is 8 hours. Avoid extended charge times to prevent damage to the battery.
when the device is fully charged, it can be used for longer than 60 minutes. A red indicator light is on during charging.
move the switch to ON to use the device

Scope of delivery

Clipper
Comb (3 mm)
Comb (6 mm)
Comb (9 mm)
leaning brush
Power pack
Oil
Load dish

Operation, cleaning and care

Switching on and off:

Slide the On/Off switch forward to turn the device on. Slide the On/Off switch back to turn the device off (fig. 1). This clipper can be used via its cable as well as without its cable. Connect the power pack to the device socket located on the bottom of the device. Then connect the power pack to the power (fig. 2).

Using the comb accessory:

CLIPSTER-18459-Kerbl-CuttoX-Cordless-Clipper-3

Make sure that the clipper is switched off when installing and removing the comb. Three combs are available (3, 6, 9 mm) for different cutting lengths. Push the comb onto the clipping head from the front, making sure that the comb engages on the bottom (fig. 3).
Press the comb up as shown in fig. 4 to remove it. You can then replace the comb with another size by proceeding as described in 1.

Clean and oil the device on a regular basis to ensure the problem-free function and full functional performance of the clippers.

Cleaning the clipping head:
The clipping head should be thoroughly cleaned once a day with regular use. Switch the device off. Disconnect the device from the power supply. Remove the comb attachment. Remove the hair with the cleaning brush.

Oiling the clipping head:
The clipping head must be oiled to ensure the good cutting results of the clipping head for as long as possible (during operation every 15 min. and when stored, preferably on a daily basis). Remove the comb attachment. Use the brush to clean the cutting edge, removing the hair between the blades. Oil the locations where the upper and lower part of the clipping head touch. The device must be oiled immediately when the shearing performance diminishes noticeably or the temperature of the clipping head seems too high. The clipping head should be oiled once per day when the clippers are not in use.

Replacing the clipping head:
The clipping head is a wear part. Despite good care, the cutting performance will diminish. At this point, the clipping head should be replaced. The clipping head can be ordered individually as a spare part (ref. no. 18458). When replacing the clipping head, you can remove the residue hair within the clippers using the brush. To remove the clipping head, remove both screws on the back. Keep these screws in a safe place for the re-installation of a new clipping head.

Cleaning the device:
Wipe off your device occasionally using a moist cloth, then rub it dry

Troubleshooting

CLIPSTER-18459-Kerbl-CuttoX-Cordless-Clipper-4

What to do, when…

the device cannot be switched on?
- is the battery empty? Connect the power pack and charge the clippers
- is the clipping head dry? The clipping head must be oiled
the clipping head does not operate smoothly?
- the clipping head must be oiled
- the top and bottom blades can become stuck when not in use for longer periods of time
the charging display does not light up when charging?
- make sure that the power pack is connected properly
the device switches off by itself?
- the battery is empty. Charge the clippers
the battery can no longer be charged?
- the battery or the power pack is defective. The power pack can be re-ordered. If the battery is defective, then the device must be disposed of properly.

Technical data

Electronic scrap
Disposing of this device after its service life is the responsibility of the operator. Please consult the valid national regulations. The device must not be disposed of in household waste. In accordance with the stipulations of the EU Directive on the Disposal of Electrical and Electronic Devices, the device can be disposed of free of charge at the local waste collection or recycling centre. Alternatively, it can be returned to retailers who offer a collection service. The proper disposal helps to ensure environmental protection and prevents any adverse effects on human health and the environment. CE-/UKCA- conformity declaration Albert KERBL GmbH hereby declares that the product / device described in these instructions complies with the fundamental requirements and other relevant stipulations and regulations. The CE-/UCKA- mark confirms compliance with the Directives of the European Union or the releant UK legislation.

Kerbl Austria Handels GmbH
Wirtschaftspark 1
9130 Poggersdorf
Tel. +43 4224 81555
Fax. +43 4224 81555-629
order@kerbl-austria.at
www.kerbl-austria.at

Kerbl UK Ltd
Lands End Way
Oakham, Rutland
LE15 6RF, UK
Phone +44 01572 722558
Fax +44 01572 757614
E-Mail enquiries@kerbl.co.uk
www.kerbl.co.uk