weboost 470166 Home Studio Cell Signal Booster Installation Guide

June 5, 2024
Weboost

weboost 470166 Home Studio Cell Signal Booster Installation Guide
weboost 470166 Home Studio Cell Signal Booster

Download the weBoost App

Icon Use our app to guide you through setting up a weBoost cell phone signal booster in your home, business, or vehicle. Boost every network, including 5G, right away.

Package Contents

Home Studio/Home Studio Lite Booster & Booster Antenna

2-30 ft. Cables

Package Contents
Outside Antenna & L-Bracket Antenna Mount

Power Supply

Operation Steps

STEP 1 Attach Booster Antenna to Booster & Place In Desired Location

Attach the booster antenna to Home Studio/Home Studio Lite booster and place in room where stronger cell signal is needed.
Operation Steps

STEP 2 Mount & Point Outside Antenna Toward Nearest Cell Tower

Pole mounting is preferred because it will be easier to adjust to the direction of the cell tower. Use the u-bolts to attach the antenna to a pole or exhaust pipe on roof.
Operation Steps

Point the outside antenna toward the nearest cell phone tower. To find the nearest tower, use an app such as ‘Open Signal’. This is the most critical step of the installation process because it will determine the overall performance of the booster system.
Operation Steps

Side Mounting

Side mounting is a option if you can still obtain strong signal.
Operation Steps

Note: Drip holes should be pointed down towards ground.

STEP 3 Route & Connect Outside Antenna To Booster Connect the white RG-6 cable to outside antenna and route and connect cable to Home Studio/Home Studio Lite booster. All connections should be finger tightened only.
Operation Steps

STEP 4 Power Up The Booster & Optimize The System

Plug the power supply into wall outlet then connect into end of booster.
Operation Steps

NOTE: We strongly recommend using a power strip with surge protection.

After powering up your system, check to see how your talk, text, and data rates have improved. If more is desired, you can optimize your system.
Operation Steps
After each rotation, observe signal level on your cell phone from the Inside Antenna’s projected area.

Rotate the outside antenna in 1/8 turn increments, after each turn, unplug and reconnect the booster to power while observing the signal level on your cell phone from the inside antenna’s projected area. When you have determined a direction that gives you the strongest signal, secure the outside antenna in place. Below gives you an idea of how much boosted cell signal coverage this system will bring indoors based on how strong the outside signal is.
Operation Steps

If the cell signal outside your home is: Strong Good Weak None
 

|

|

|

Your boosted cell signal will cover:| Large Room| Medium Room| Small Room| None

Status Light Patterns

Status Light Patterns Status Light
Patterns

GREEN
This indicates that your Home Studio or Home Studio Lite booster is functioning properly and there are no issues with installation.

SOLID RED
Band has shutoff. This is due to a feedback loop condition called oscillation. This is a built in safety feature that causes a band to shut off to prevent harmful interference with a nearby cell tower. Refer to Troubleshooting section.

BLINKING GREEN, RED
This indicates that the booster is operating at a reduced gain to prevent oscillation (feedback). This is a built in safety feature to prevent harmful interference with a nearby cell tower. If you are already experiencing the desired signal boost, then no further adjustments are necessary. If you are not experiencing the desired boost in coverage then refer to the Troubleshooting section.

BLINKING GREEN, YELLOW
This indicates band has reduced gain. This indicates that one or more of the booster bands has reduced power due to overload from nearby cell tower. This is a built in safety feature to prevent harmful interference with a nearby cell tower. If you are already experiencing the desired signal boost, then no further adjustments are necessary. If you are not experiencing the desired boost in coverage then refer to the Troubleshooting section.

SOLID YELLOW
Band has shutoff due to overload from nearby cell tower. Outside antenna must be adjusted. Refer to Troubleshooting section.

LIGHTS OFF
If the signal amplifier’s light is off, verify your power supply has power.

Troubleshooting

FIXING RED LIGHT ISSUES
This involves Solid Red & Blinking Green/Red lights.

  • Tighten all cable connections (be sure to handtighten only, do NOT use tools).
    You may want to undo and redo the connection completely. Unplug and replug in power supply.

  • Increase the distance (horizontally or vertically) between the outside and inside antennas. Add included cable if needed. Unplug and replug in power supply.

FIXING ANY YELLOW LIGHT ISSUES
This involves Solid Yellow & Blinking Green/Yellow lights.

  • Outside Antenna must be adjusted. Disconnect and reconnect power between adjustments. Wait at least 10 seconds between adjustments for the lights to reset.
    Pole Mount Option: Rotate the outside antenna away from the strongest cellular signal in small increments (1/8 turn) until the light turns green. Unplug and replug in power supply. Mounting On Side Of Roof Option: Change mount location. Move the outside antenna to location of the home/building to see if the lights turn green. Unplug and replug in power supply. Then secure in place.

Safety Guidelines

Verify that both the outside antenna and the adapter extension cable are connected to the signal amplifier before powering up the signal amplifier.

Use only the power supply provided in this package. Use of an incorrect power supply may damage your equipment.

RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons.

AWS Warning: The outside antenna must be installed no higher than 31 feet 9 inches above ground.

This is a CONSUMER device.

BEFORE USE , you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.

In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05.

You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST NOT be installed within 20 cm of) any person.

You MUST cease operating this device immediately if requested by the FCC (or ISED in Canada) or licensed wireless service provider.

WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.

This device may be operated ONLY in a fixed location for in-building use.

FOR MORE INFORMATION ON REQUIREMENTS SET OUT IN ISED CPC-2-1-05, SEE BELOW:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html

FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS PROVIDER, PLEASE SEE BELOW:

T-Mobile/Sprint/MetroPCS : https://www.t-mobile.com/support/coverage/register-a-signal-booster

Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register- signal-booster.html

AT &T: https://securec45.securewebsession.com/attsignalbooster.com/

U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster- registration.jsp

Antenna Info

The following accessories are certified by the FCC to be used with the Home Studio or Home Studio Lite Cell Signal Boosters.

This radio transmitter 4726A-460065 and 4726A-460066 has been approved by innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

HOME STUDIO BAND 2 BAND 4 BAND 5 BAND 12 BAND 13
Outside antenna maximum permissible antenna gain (dBi) 50Ω 6.1 5.8 4.5
4.9 4.9
HOME STUDIO LITE BAND 12

| BAND 13
Outside antenna maximum permissible antenna gain (dBi) 50Ω| 4.9| 4.9
INSIDE ANTENNA INFO

#| Coax Type| Ln(ft)| Antenna Type|
311236| NONE| 0| Omni| 50
OUTSIDE ANTENNA INFO
#| Coax Type| Ln(ft)| Antenna Type|
314475| RG-6| 30| Directional| 75
314473| RG-6| 30| Panel| 75
304421| RG-6| 30| Omni| 75

Specifications

Home Studio Cell Signal Booster

Model 460066
FCC PWO460066
IC 4726A-460066
Connectors F-Female / SMA Female
Antenna Impedence 75 Ohms / 50 Ohms
Frequency 698-716 MHz, 728-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz,

1710-1755/2110-2155 MHz
Power output for single cell phone (Uplink) dBm| 700 MHz B12/17
23.3| 700 MHz B13
22.2| 800 MHz B5
23.3| 1700 MHz B4
22.1| 1900 MHz B2
21.8
Power output for single cell phone (Downlink) dBm| 9.4| 9.6| 7.0| 11.8| 13.8
Noise Figure| 5.0 dB (nominal)
Isolation| > 90 dB
Power Requirements| 4.2V, 2.5A

Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor.

The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. This device complies with Part 15 of FCC rules.
This device contains licence-exempt transmitter(s)/receiver(s that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference, and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment.

Home Studio Lite Cell Signal Booster

Home Studio Lite Cell Signal Booster

Model| 460065
FCC| PWO460065
IC| 4726A-460065
Connectors| F-Female / SMA Female
Antenna Impedence| 75 Ohms / 50 Ohms
Frequency| 698-716 MHz, 728-756 MHz, 777-787 MHz
Power output for single cell phone (Uplink) dBm| 700 MHz B12/17
24.3| 700 MHz B13
23.0
Power output for single cell phone (Downlink) dBm| 11.7| 12.9
Noise Figure| 5.0 dB (nominal)
Isolation| > 90 dB
Power Requirements| 4.2V, 1.2A

Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor.

The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. This device complies with Part 15 of FCC rules.
This device contains licence-exempt transmitter(s)/receiver(s that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference, and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment.

Register your Signal Booster now!

Complete the two easy steps to register your booster and receive premium customer service, special offers and more!

Step 1: Take a photo of your Photoregister Code including the points ( ).
Register your Signal Booster now

Step 2: Send it in.

Smartphone U.S. only
Text photo to 71403
OR
Email U.S./CAN
weboost@photoregister.com
OR
Online
register.weboost.com

Need help? Visit photoregister.com/help or text HELP to 71403.

1-866-294-1660
www.weboost.com
support@weboost.com

2 YEAR WARRANTY

weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.

Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product.

This warranty does not apply to any Signal Boosters determined by weBoost to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.

Replacement products may include refurbished weBoost products that have been recertified to conform with product specifications.

RMA numbers may be obtained by contacting Customer Support.

DISCLAIMER: The information provided by weBoost is believed to be complete and accurate. However, no responsibility is assumed by weBoost for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.

3301 East Deseret Drive, St. George, UT

1.866.294.1660
www.weboost.com
support.weboost.com

Copyright © 2020 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents

NOT AFFILIATED WITH WILSON ANTENNA
GDE000477_001_03.24.22

Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Weboost User Manuals

Related Manuals