JBC RWB Rework Adjustable Arm for PHB Instruction Manual

JBC RWB Rework Adjustable Arm for PHB

This manual corresponds to the following reference: RWB-B

Packing List

The following items are included:

• Tool Arm  1 unit
  

• Base  1 unit

• Height Adjustment Flange  1 unit

• Adapter for TET  1 unit

• Adapter for JTT 1 unit

• Hose Clamp 1 unit

• Headless Screw 1 unit

• Allen Key 3 mm  1 unit
  

• Manual 1 unit

Features

• Scaled Vertical Axis (mm / in
• Hight Adjustment Flange
• Tool Holder
• Adapter for JTT / TET
• Bas
• Hose Clam
• Tool Ar
• Headless Screw (at the rear
• ESD Connector (connect to ESD Common Grounding Point)

Tool Arm Assembly

Setting up the Tool Arm

1. Fit the tool arm
2. and the height adjustment flange
3. onto the vertical axis.  Then the vertical axis into the base bushing .
4. Tighten the headless screw by using the Allen key.

Heater Hose Assembly

• Inserting the Adapter (JT/TE)
• Slide the adapter along the hose to the end of the handle.

Fit Heater into Tool Holder

• Insert the tool as far as possible into the tool holder with its adapter previously assembled.
  

Lower the Tool

• Turn the lever to lower the tool. After having finished the working process raise the tool to free up the workspace.

Fit Heater Hose to Hose Clamp

1. Fit the heater hose into the hose clamp
2. and move the closure down .

Tool Arm Height Adjustment

1. 1. Make sure the tool arm knob is loosened

2. before adjusting the tool holder height. Slide the tool arm to the appropriate height
3. and secure its position by tightening the height adjustment flange knob .
   The scale on the vertical aixis allows to adjust the desired height easily

Work Position Adjustment
According to the work needs the tool arm allows adjustments for different positions. The articulated arm covers the entire working area.

1. 1.       1. Position the arm as needed and open or tighten the knobs (1)

   2. and to allow or block the movement (A) and (B).

Tool Holder Adjustment

• The tool holder head position enables an individual tool position adjustment. By pressing the button and/or loosen the wheel the tool holder head position can be adjusted. Both axes have a scale to carry out the task with higher precision .

• Wheel Scale

• Wheel

• Button

• Button Scale

• Tool Holder

• Head

• Tilting movement

• By pressing the button you can rotate the Tool Holder up or down.
  

• The movement allows a rotation between -40º and +40º.

Rotating movement

• You can lock or unlock the lateral rotation mechanism by turning the fixing wheel a quarter.

• The movement allows a rotation between -90º and +90º.

**Compatible JBC Articles***

1. HRR and HRL can be combined with RWT, RWS or RWB. Assemble first the height adjustment flange ,
2. then the HRR
3. and afterwards the HRL .
4. Assemble the second height adjustment flange
5. and finally the RWT۔

• Heights Adjustment Flange (2nd)
• HRL Rework Left Hand Support
• Place the preheater set in the area below the hot air tool
• RWT Rework Adjustable Arm Without Base
• Heights Adjustment Flange (1st)
• HRR Rework Right Hand Support

4 different sizes for PCB Supports are available:

• *  PHNK Nano Preheater Set

  •  PHSK Small Preheater Set-
  • PHBK Large Preheater Set-
  • PHXK XL Preheater Set

Accessories

PHBK Large Preheater Set

JBC offers PHBK for rework on medium and large PCBs. It features four thermocouple connections and a heating area which is divided in two zones:

•  1 zone: 180 x 277 mm / 7.1 x 10.9 in

•  2 zones: 360 x 277 mm / 4.2 x 10.9 in
  PHBK includes the preheater with its console and the PCB support.

• Large PCB Support

• Console

• Large Preheater

PSB Large PCB Support

Also available JBCs Large PCB Support PSB – it comes without preheater. PSB adapts to different PCBs geometries by means of its adjustable components and its 3 adjustable height positions 28, 38 or 48 mm / 1.1, 1.5 or 1.9 in.

Maintenance

•  Check periodically that RWB is clean, especially the sliding parts and the axis.

•  Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts.

•  Replace any defective or damaged parts. Use original JBC spare parts only.

•  Repairs should only be performed by a JBC authorized technical service.
  

• Sliding Parts

• Axis

Safety

• It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosions.

• Do not use the equipment for any purpose other than PCB rework. Incorrect use may cause fire.

•  The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.

•  Be careful with the fumes produced when soldering.

•  Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.

•  Utmost care must be taken with liquid tin waste which can cause burns.

• This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance.

• Maintenance must not be carried out by children unless supervised

Specifications

References

• JBC Soldering Stations, Irons and Rework equipment for electronics
• Warranty Extension

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>