Dr Heater DR-908 Wall Hung Infrared Heater Owner’s Manual

Dr Heater DR-908 Wall Hung Infrared Heater Owner’s Manual

FEATURES

• 1500 Watts with Two Heat Settings
• Thermal Cutoff Protection
• Tip-Over Switch
• Room Temperature LED Display
• Precision Temperature Control
• Easy Push-Button Controls
• Advanced Dual Heating System (ADHS)
• With foldable leg which can be used on floor application

PLEASE READ AND SAVE THESE INSTRUCTIONS

COGRATULATIONS!

The Dr. Infrared Heater you have just purchased is a safe and powerful heater, designed to heat a room after a few minutes of operation. The far-infrared Quartz-PTC heating system is an excellent choice for safely heating whole room, while saving on heating costs.

Additionally, this heater includes an overheat protection system, and an inlet air overheat protection system designed to ensure your safety.

This heater does not reduce humidity or oxygen in your home or office, promoting a healthier environment!

Before using your Dr. Infrared Heater, please take a few minutes to read these instructions, and review the product’s limited warranty.

Thank you!

WARNING! To reduce the risk of fire, electric shock, or personal injury, read all the instructions before using this heater. This appliance is intended for household or personal use only as described in this manual. Any other use including but not limited to commercial, agricultural, or outdoor use, is not recommended by the manufacturer and may cause fire, electric shock, injury and/or damages. The use of any attachments and/or accessories not recommended or sold by Dr. Infrared Heater Products may cause hazards and void the warranty.

CAUTION- High temperature! Keep electrical cords, drapery, and other furnishings at least 3 feet (0.9 m) from the front and rear of the heater.

IMPORTANT INSTRUCTIONS

When using this appliance, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following.

1. Read all the instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handle when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.

3. Extreme caution is necessary when any heater is used by or near children or persons with physical challenges and whenever the heater is left operating and unattended.

4. Do not operate the heater with a damaged cord or plug, or after the heater malfunctions, has been dropped, or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.

5. Do not use outdoors.

6. This heater is not intended for use in bathrooms, laundry areas or similar locations. Never locate the unit where it may fall into a bathtub or other water container.

7. Do not run the cord under carpeting and do not cover the cord with throw rugs, runners or the like. Do not route cord under furniture or appliances.
   Arrange the cord away from traffic areas to avoid a tripping hazard.

8. To disconnect the heater, turn controls to OFF, then remove the plug from outlet.

9. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, or fire, or damage to the heater.

10. Connect to properly grounded outlets only.

11. To prevent a possible fire, do not block air intakes or exhaust openings in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. Use the heater on flat, dry surfaces only.

12. A heater has hot and arcing or sparking parts inside. Do not use the heater in areas where gasoline, paint or flammable liquids are used or stored.

13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.

14.  Never clean this heater while it is plugged in. Do not immerse in water. To disconnect, turn control to OFF, then remove the plug from the outlet by grasping it and pulling it from the outlet. Never yank on the cord.

15. Always unplug the heater when it is not in use.

16. Always plug heater directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).

17. It is normal for the heater’s plug and cord to feel warm to the touch. A plug or cord which becomes hot to the touch or becomes distorted in shape may be a result of a worn electrical outlet. Worn outlets or receptacles should be replaced prior to further use of the heater. Plugging this heater into a worn outlet may result in overheating of the power cord or fire.

18. Make sure the plug is fully inserted into an appropriate receptacle. Be mindful that receptacles also deteriorate due to aging and continuous use.
    Check periodically for signs of overheating or deformations of the plug. If any overheating or deformation occurs, immediately discontinue using the heater and contact Dr. Infrared Heater Authorized Service Center.

19. CHECK YOUR HEATER CORD AND PLUG CONNECTIONS. Faulty wall outlet connections or loose plugs can cause the outlets or plug to overheat.
    During use, please check frequently to determine if your plug outlet or faceplate is HOT! If it is hot, discontinue using the heater and/or make certain a qualified electrician checks and replaces the faulty outlet(s).

CAUTION: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Product Specifications

• Voltage Rating: 120V (60Hz)

• Power Consumption: 1500W

• Unit Size:
  15-17/64 in. (H) x 11-21/64 in. (W)
  x 6-21/64 in. (D)

• Unit   Weight: 8.46 lbs.

Special Features

LED Display – When the unit is plugged in, the POWER LED will light. To turn the heater ON, press the MODE button, the heater will wait in ECO Mode. At ECO mode, it will display the set value 2 minutes after the desired temperature is set.

Overheat Cut-Off Protection System – This heater includes a protection system that cuts off the unit if it overheats for any reason.

Inlet Air Overheat Protection System – This heater will automatically cut off if the inlet air duct becomes obstructed and causes the unit to overheat.

Safety Tip-Over Switch – The Dr. Infrared Heater is designed to cut off automatically when tipped in any direction. Place the heater on a flat, smooth, stable surface to prevent the heater from tipping over again. When returned to a normal upright position, the heater is ready for use again. This is a safety feature to avoid the possibility of fire should the unit be tipped accidentally.

Advanced Dual Heating System (ADHS) – Dr. Heater is the first to feature a dual heating system for maximum heat transfer rate. It combines the energy efficiency of infrared heat with the comfort of convection heat to heat your room fast and comfortably—without hot spots and cold spots.

Product Overview

Features

• A. “Cool-Touch” cabinet
• B. POWER LED
• C. ON/OFF button
• D. MODE button
• E. LED temperature display
• F. Increase temperature button
• G. Decrease temperature button

Installation Instructions

This heater has foldable legs which can be used on floor application. It can also be mounted on the wall.

On the Floor

Open wide the foldable legs and the unit can stand freely on the floor.

On the wall

1. Dill the required holes with the ST4x20 screws (Included) as below.
   

2. Hang up the heater with the hanging hole to the screws.

Operating Instructions

1. Plug the power supply cord into a grounded wall outlet. (120VAC, 60Hz)
   IMPORTANT: This heater is for use on 120 volts. This heater comes with a grounded (three-prong) plug. The grounded plug must be used with a grounded outlet. Do not used an adapter in two-slot wall outlet unless the grounded plug of the adapter properly connects to a building ground. Using the heater without a properly grounded outlet or adapter could result in an electric shock hazard.
   The cord has a plug as shown at A in the following figure. An adapter, as shown at C, is available for connecting three-blade grounding type plugs to two-slot receptacles The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
   Grounding methods
   

2. TURNING THE HEATER ON

3. Plug in unit to power outlet, the POWER LED will light. To turn the heater ON, press the MODE button, the heater will wait in ECO Mode.

4. HEATING MODES
   Press the MODE button to toggle between the different modes: ECO, HIGH, LOW. Heater exit from any mode to standby mode by pressing the STANDBY button.

5. ECO MODE – 1500W/1000W
   ECO mode is a computerized mode to optimize energy efficiency. It will programmatically select between HIGH and LOW power mode to heat up the room to the desired temperature in the most effective way. Once the desired temperature is achieved, the heater will maintain the room to the set temperature. ECO mode is the environmentally friendly operating mode.

6. HIGH POWER MODE – 1500W
   HIGH mode will control the heater to operate at high power until the room reached the set temperature. The heater will stop heating and initiate component cooling process before turning off the fan. Once the desired temperature is achieved, the heater will maintain the room to the set temperature.

7. LOW POWER MODE – 1000W
   LOW mode will control the heater to operate at low power until the room reached the set temperature. The heater will stop heating and initiate component cooling process before turning off the fan. Once the desired temperature is achieved, the heater will maintain the room to the set temperature.

8. SETTING THE TEMPERATURE
   Choose the desire Mode: ECO, HIGH, or LOW. To set the desired temperature:
   Press the button once until the numeric temperature starts flashing.
   Press the button again to increase the temperature or the button to decrease the temperature.
   Once the temperature is set, the heater will warm up the room using the selected Mode. Heater will sample the room temperature every 4 minutes after the desired temperature is reached.

9. Night Mode
   Night mode is design for quiet operation in the night. When the surrounding environment becomes dark, or the heater can’t detect the light, it will turn into the Night Mode automatically. In this mode, when the heater reached the set temperature, it will sample the room temperature less frequently, 30 minutes per sample. When the heater detects the light, it will turn into the ECO Mode automatically.

10. Night Mode
    Night mode is design for quiet operation in the night. When the surrounding environment becomes dark, or the heater can’t detect the light, it will turn into the Night Mode automatically. In this mode, when the heater reached the set temperature, it will sample the room temperature less frequently, 30 minutes per sample. When the heater detects the light, it will turn into the ECO Mode automatically.

11. Display the room temperature
    The display shows the set temperature all the time, press and hold the MODE button and then press the button. The room temperature will display for 30 seconds. It will return to set temperature after 30 seconds.

12. Display Celsius
    To display Celsius, press and hold the MODE button for 2 seconds. Press and hold the MODE button for 2 seconds again to change back to Fahrenheit.

Remote Controller

HOW TO INSERT BATTERIES

NOTE: Remove the batteries if the remote control is not to be used for a month or more. Batteries left in the unit may leak and cause damage.
DO NOT MIX OLD AND NEW BATTERIES IN USE! DO NOT MIX ALKALINE, STANDARD (CARBON-ZINC) OR RECHARGEABLE (NICKEL-CADMIUM) BATTERIES IN USE!

Instructions for the Use of the IR Remote Control
The buttons on the remote controller functions in the same manner as those on the control panel on the front of the heater. Set the timer by using the remote control.

Setting the Timer

1. Press the TIMER button until Set Time starts flashing. The default value is 3 hours.
2. Press the “+” button to increase the set time or the “–” button to decrease the set time. The timer can be set from 1 to 12 hours. The timer will set and execute after the LED display stops flashing. The heater will shut OFF automatically when the set time is reached.
3. To turn the timer OFF, follow step 1, pressing the “–” button to set the time to 0. The timer feature will turn off when the LED stops flashing.

Maintenance

1. Always turn OFF the heater and disconnect the cord from the electrical outlet before cleaning the unit.

2. Light accumulation of dust may be removed from the heater with a soft cloth or vacuum cleaner.

3. Wipe the exterior surfaces of the heater occasionally with a damp cloth (not dripping wet), using a solution of mild detergent and water. Dry the case thoroughly before operating the heater.
   Caution! Do not allow water to run into the interior of the heater as this could create a fire or electric shock hazard.

4. The fan motor is factory-lubricated for life and will require no further lubrication.

5. Store the heater in a clean, dry place when it is not in use.

Cleaning the electrostatic filter

The heater has an electrostatic filter located at the rear. The cleaning of the filter should be performed once per month or as needed (when dust is visible on the filter) to ensure efficient operation of the heater.

1. Power the heater OFF by pressing the POWER button located on the left side of the Control Panel.
2. Unplug the heater’s power cord.
3. Release the filter bracket by pushing the filter bracket up from below (Figure 1).
4. Remove the filter bracket by pulling down and out (Figure 2).
5. Clean the filter by vacuuming.
6. Replace the filter bracket by sliding the bottom down into the slot on the back of the heater (Figure 2). Then gently push the bottom of the filter bracket into place (Figure 1).
   

Warning: Any other servicing needed must be performed by an authorized service representative. Do not attempt to service the unit yourself.

Product Specifications

• Model No.: DR-908

• Voltage: 120V, 60Hz

• Current: Maximum continuous draw:
  12.5 amps

• Output: 5200 BTUs

• Power: 1500 Watts

• Blower: Multi-blade; Low Noise, High Pressure

Warranty Information

Register your product at our website:

Or visit DrHeaterUSA.com/register-your-heater

Feedback

Love it? Help us make the product more for you.

Let us know with a customer review.
Please visit: https://www.amazon.com/review/review-your-purchases#

At Dr. Heater USA, we are committed to bringing top quality alternative & supplemental heating products to our customers.

Note: There may be a trace of smoke or odor when the unit is first operated. Do not be alarmed. This indicates a drop of oil fell on the interior coils during the manufacturing process. It will quickly evaporate and should not recur.

How long is the warranty?

This heater comes with a ONE-YEAR LIMITED COMPONENT WARRANTY. If your unit does not appear to be working properly, please contact our service center by calling 1-800-317-1688. Prior to your call, we encourage you to visit our service-related website www.DrHeaterUSA.com for troubleshooting tips and service instructions if needed.

DR-908Pre-drilledTemplate for Wall Mounting

Pleaseprintwith A4 sizepaper
8¼ x11¾ in
210x297mm
Please use a rule rafter printout to make sure the printing is the correct size before drilling

Contact Us

Dr. Infrared Heater
860 Mahler Rd, Burlingame
CA 94010
Tel: 1-800-317-1688
EMAIL: SERVICE@DRHEATERUSA.COM
Dr Heater USA
@DrHeaterUSA
Dr. Heater USA
Dr. Heater USA

References

• Register Product – Dr. Infrared Heater
• Dr. Infrared Heater Space Heaters Commercial Industrial Home Office Heaters
• Dr. Infrared Heater Space Heaters Commercial Industrial Home Office Heaters
• Amazon Sign-In
• Amazon Sign-In

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>