anslut 019927 10W Work Lamp with Magnification LED Instruction Manual

June 5, 2024
anslut

AnSlut

anslut 019927 10W Work Lamp with Magnification LED

anslut-019927-10W-Work-Lamp-with-Magnification-LED

SAFETY INSTRUCTIONS

  • Only intended for indoor use.
  • Never attempt to dismantle or repair the product yourself. Any repairs must be carried out by an authorised electrician.
  • Pull out the plug before cleaning and maintenance.
  • A damaged power cord must be replaced by an authorised service centre, or a qualified person, to ensure safe use.
  • Do not connect the product to the mains while it is still in the pack.
  • Do not look directly into the light when it is switched on. Never point the beam at the eyes of people or animals.
  • The light source is not replaceable. Discard the product if the light source stops working.

SYMBOLS 

TECHNICAL DATA

  • Rated voltage: 230 V ~ 50 Hz
  • Output: 10W
  • Luminous flux: 730 Im
  • Life span: 25 000 h
  • Diffusion angle: 720°
  • Cord length: 7.5 m

DESCRIPTION

Work lamp with magnification adjustable both horizontally and vertically. Fastens to workbench/table and provides a reflection-free light.

Use

  1. Place the product in the required place.
  2. Plug the plug into a power point.
  3. Turn the light on with the switch.

MAINTENANCE

Wipe the product with a dry, soft cloth when necessary.

PRODUCT INFORMATION SHEET

Supplier’sname or trademark: Anslut
Supplier’s address (‘): Jula AB, Julagatan2, SE-53237 Skara
Number of hot zones and/or surfaces:
Type of light source:
Lighting technology used: LED

Light source connected to mains supply or

light source not connected to mains supply:

| MLS| Connected light source (CLS):| no
Light source with optional colour:| no| Envelope:| no
High luminance light source:| yes|  |
Anti-glare shield:| yes| Can be used withdimmer:| no
Product parameters
Parameter| Value| Parameter| Value
General product paramete :
Energy consumption in on-mode (kWh/

1000 hi

| lOx| Energyefficiency class|
Useful luminous nux (¢..,), indicating if it refers tothe fiux in a sphere (360°), in a wide cone (120°) or in a narrow cone (90°).|

730 wide cone

| Correlated colour temperature, rounded to the nearest 100 K, or the range of correlated colour temperatures, rounded to the nearest

100 K, that can be set.

|

3500 [x/x…x]

On-mode power (p ), expressed in watt.

00

| 10 x,x| Standby power (p,,), expressed in watt and

rounded to the second decimal.

| 0 x,xx
Networked standby power (p ,) for CLS,

0

expressed in watt and rounded tothe second

decimal.

|

x,xx

| Colour rendering index (CRI), rounded to

the nearest integer, or the range of CRI values that can be set

|

80 [x/x…x]

Outerdimensions without separate actuator for lighting and non-lighting parts, where appropriate (in mm)| Height| 480x|

Spectral power distribution in the range 250 nm to 800 nm, at full-load.

|   [graphic]
Width| 770x
Depth| 210x
Claimof equivalent power(‘).| [yes/-]| If yes, equivalent power (WI|
 |  | Chromaticitycoordinates (x and y)| x: 0.409

y 0.394

Parameters for directional light sources:
Peak luminous intensity(cd)| 338 X| Beam angle in degrees, or the range of beam angles that can be set| 120[x/x…x]
Parameters for LED and OLEO light sources:
R9 colour renderingindex value| 2x| Life span factor| 0.90x,xx
Luminous fiux ratio| 0.96x,xx|  |
Parameters for LED and OLEO mains light sources :
Displacement factor (cos q>l)| 0.50 x,xx| Colour consistency in MacAdam ellipses| 6x
Claimthat an LED light source replaces a nuorescent light source without integrated ballast of a specific wattage.|   [yes/-]|

If yes, claimed replacement power (WI

|
Flicker metric {Psi LM)| lO x,x| Stroboscopiceffect metric {SVM)| 0.9 x,x

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals