Gude BS 12 Cordless Drill Driver Instruction Manual
- June 5, 2024
- Gude
Table of Contents
Gude BS 12 Cordless Drill Driver
WHAT IS IN BOX
Starting-up the machine
Operation
LED LIGHT
HOW TO SET THE CHUCK
START /STOP
GEAR SELECTOR SWITCH
HOW TO USE
Technical Data
Cordless Drill Driver| BS 12|
---|---|---
Cordless percussion drill/driver| | BSB 12
Art. No| 58600 / 58601 /
58602 / 58603
| 58604 / 58605 /
58606
Battery voltage| 12 V | 12 V
No-load speed| 1st gear 2nd gear| 0 – 400 min-1
0 – 1300 min-1
| 0-400 min-1
0-1300 min-1
Rate of percussion under load| 1st gear 2nd gear| –
–
| 0-6000 min-1
0-19500 min-1
Torque max.| 25 Nm| 25 Nm
Drilling capacity max.| Steel plate Wood
brick and tile
| 10 mm
20 mm
–
| 10 mm
20 mm
10 mm
Screw diameter max. (Wood)| 6 mm| 6 mm
Drill chuck range| 0,8 – 10 mm| 0,8 – 10 mm
Weight without battery/Charging equipment| 0,8 kg| 0,85 kg
Noise details
Measured according to EN 60745; Uncertainty K = 3 dB (A)
Sound pressure level LpA| 83,14 dB(A)| 83,14 dB(A)
Sound power level LWA| 94,14 dB(A)| 94,14 dB(A)
Wear ear protectors!
Vibration details
Vibration total values (triaxial vector sum) determined according to EN 60745, Uncertainty K = 1,5 m/s2
Drilling into metal: Vibration emission value ah,D| 2,39 m/s²| 2,39 m/s²
Impact drilling into concrete: Vibration emission value ah,ID| –| 9,56 m/s²
Screw driving without impact: Vibration emission value ah| 1,15 m/s²| 1,15
m/s²
WARNING:
The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the level given in this information sheet. The vibration emission level may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. An accurate estimate of the vibratory load should also take into account the times when the tool is shut down or when it is running but not actually in use. This may significantly reduce the vibratory load over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.
Read and understand the operating instructions before using the appliance. Familiarise with the control elements and how to use the appliance properly. Abide by all the safety measures stated in the service manual. Act responsibly toward third parties. The operator is responsible for accidents or risks to third parties. Persons over 16 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge under supervision of the trainer during occupational education In case of any doubts about connection and operation refer please to our customer center
Specified Conditions Of Use
BS 12: The battery drill/screwdriver may be used for drilling and screwdriving for independent use away from mains supply. BSB 12: The cordless percussion drill/driver is designed for drilling, percussion drilling, as well as screwdriving for independent use away from mains supply. Do not use this product in any other way as stated for normal use. Not observing general regulations
Emergency procedure
Conduct a first-aid procedure adequate to the injury and summon qualified medical attendance as quickly as possible. Protect the injured person from further harm and calm them down. If you seek help, state the following pieces of information:
- Accident site,
- Accident type,
- Number of injured persons,
- Injury type(s
Symbols
BATTERY
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
Screwdriver safety warnings
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a „live“ wire may make exposed metal parts of the power tool „live“ and could give the operator an electric shock.
Drill safety warnings
Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a „live“ wire may make exposed metal parts of the power tool „live“ and could give the operator an electric shock.
Additional Safety and Working Instructions
Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear and ear defenders. The dust produced when using this tool may be harmful to health. Do not inhale the dust. Use a dust absorption system and wear a suitable dust protection mask. Remove deposited dust thoroughly, e.g. with a vacuum cleaner. Do not machine any materials that present a danger to health (e.g. asbestos). When working in walls ceiling, or floor, take care to avoid electric cables and gas or waterpipes. Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage. Please turn the device immediately off when the tool used gets blocked! Do not turn the device on again when the tool is still blocked. This could cause bounce back with a high reaction moment. Determine and remove the cause of the blocking of the tool used while respecting the safety instructions. The possible causes may be:
- it is tilted in the workpiece to be machined
- it has pierced through the material to be machined
- the power tool is overloaded Do not reach into the machine while it is running
- Chips and splinters must not be removed while the machine is running.
WARNING!
- Danger of burns The insertion tool may become hot during use.
- when changing tools
- when setting the device down The appliance must not be used if damaged or safety equipment is defective. Replace any worn-out and damaged parts.
- Do not use the device near flammable liquids or gases. Risk of fire and explosion in case of short circuit.
- Do not let any metal parts reach the airing slots – danger of short circuit!
Battery
Risk of fire! Risk of explosion! Never use damaged, defective or deformed accumulators. Never open or damage the accumulator or let it fall on the ground. Umgebungstemperatur Protect the battery against heat and fire. Battery to be used at the ambient temperatures between 10°C and +40°C only. Never put the battery on heaters and do not expose it to strong sunlight for a long time. After being subject to heavy load, let the battery cool down first. Short circuit – do not bridge the accumulator contacts with metal parts. The accumulator must be packaged (plastic bag, box) or accumulator contacts must be sealed up for accumulator disposal, transport or storage. The Güde charger to be used only to charge the battery. There can be malfunction or fire if different chargers are used. Vapours may leak out in case of unauthorised use or when using a damaged accumulator. Bring fresh air and seek medical advice if experiencing difficulties. Vapours may irritate the respiratory system.
Work instructions
Accumulators are supplied partially charged and must therefore be fully charged before being used for the first time.
- Charge the accumulator when the appliance is running slowly or stops.
- A li-ion battery may be charged at any time without any shortening of its life. Charging process interruption will not damage the accumulator.
- A li-ion battery is protected by the Electronic Cell Protection against deep discharge.
- A significantly shorter operating time of a charged battery means the battery life is over and the battery must be replaced.
Dispose of the batteries in an environmentally friendly manner.
Li-ion batteries are subject to the special disposal obligation. Have any defective batteries disposed of by a specialized shop. The battery must be taken out before the appliance is scrapped. Damaged batteries may harm the environment and your health if toxic vapours or liquids leak out of such batteries. Therefore, never send a defective battery by post, etc. Please contact your local recycling centre. Dispose of the batteries when discharged. We recommend applying adhesive tape on the poles to protect them against short circuit. Never open the battery.
Maintenance
Take the replaceable battery from the appliance before any extension, cleaning and servicing works. Repairs and works specified in these Instructions may only be performed by qualified authorised staff. Use only original accessories and original spare parts. Keep the device, in particular the air vents, clean at all times. Never spray water on the device body! Do not clean the plastics with solvents, flammable or toxic fluids. For cleaning, use a damp cloth only. Only a regularly maintained and treated appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to unforeseen accidents and injuries. If necessary, a list of spare parts can be found at www.guede.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>