omtech LYF-30BWe Split Fiber Marking Machine User Manual
- June 5, 2024
- omtech
Table of Contents
omtech LYF-30BWe Split Fiber Marking Machine
PREFACE
Thank you for choosing our laser equipment.
This fiber laser marking machine is intended for personal and professional
use. Read this manual carefully before operation. It covers the details of
correct installation, adjustment, maintenance, and—most importantly—safe
operation of your new laser. It is intended to be used in conjunction with the
manual for its engraving software, as the program not only provides image
design but also serves as the main interface for the laser settings and
machine controls. You and any other users of this device should thoroughly
understand BOTH manuals before attempting to operate the laser. Both manuals
should be included if this device is given or sold to a third party. If you
have any questions, after reading these manuals, please contact us and our
support department will address your concerns as soon as possible.
Introduction
General Information
-
This manual is the designated user guide for the installation, setup, safe operation, and maintenance of your fiber laser marking machine. It is divided into six chapters covering general information, safety instructions, installation steps, operation instructions, maintenance instructions, and contact information.
-
All personnel involved in the installation, setup, operation, maintenance, and repair of this machine should read and understand this manual, particularly its safety instructions. Substandard performance and longevity, property damage, and personal injury may result from not knowing and following these instructions.
-
Your fiber laser marker works by emitting a powerful laser beam from its fiber laser source, sending that beam through a fiber optic cable, focusing its power through the galvanometer lens, and using this focused light to etch designs into certain substrates.
This fiber laser marking machine uses a nanoscale fiber laser source. Its single-mode output, good heat dissipation, high efficiency, and compact structure make it ideal for high-precision laser marking. With typical use, this device has an average lifespan around 100,000 working hours. However, constantly running your laser above 80% of its maximum rated power can significantly shorten its service life. It is recommended to use settings from 10–75% of the maximum rated power to enjoy optimal performance and longevity.
Note that this is a high-voltage device and, as a safety precaution, it is recommended to only touch its components with one hand at a time during use. -
Note also that this device does not have a protective housing. It is thus recommended to use a special room or to raise protective screens around the work area. The active laser is invisible to the human eye and anyone in or near the working area MUST use special protective eyewear when the laser is in use to avoid potentially permanent injury.
Symbol Guide
The following symbols are used on this machine’s labeling or in this manual:
- These items present a risk of serious property damage or personal injury.
- These items address similarly serious concerns with regard to the laser beam.
- These items address similarly serious concerns with regard to electrical components. Protective eyewear should be worn by anyone around this machine during operation.
- This product is sold in conformity with applicable EU regulations.
- This product contains electrical components that should not be disposed of with regular garbage.
Designated Use
This machine is intended for use engraving signs and other consumer products
on applicable substrates. This laser can process a wide variety of metals
including steel, aluminum, titanium, brass, copper, tungsten, carbide, and
chrome. It can also be used with stone and some hard plastics such as acrylic.
(See §§2.5 & 4.3 for further details.) Use of this system for non-designated
purposes is not permitted.
The system must be operated, maintained, and repaired by personnel familiar
with the field of use and the dangers of the machine and the material being
engraved including its reflectivity, conductivity, potential for creating
harmful or combustible fumes, etc.
Laser beams are dangerous. The manufacturer and/or seller bear(s) no
responsibility and assume(s) no liability for any improper use of this device
or for any damage or injury arising from such use. The operator is obliged to
use this fiber laser marker only in accordance with its designated use, the
other instructions on the device and in its manuals, and all applicable local
and national laws and regulations.
Technical Specifications
Model | LYF-30BWe |
---|---|
Input Power | 110V/60Hz |
Rated Power | 30W |
Expected Service Life | 100,000 hr. |
Laser Wavelength | 1064 nm (1.064 µm) |
Laser Frequency | 30–60 kHz |
Processing Area | 6.9×6.9 in. (17.5×17.5 cm) |
Max. Marking Speed | 275.6 ips (700 cm/s) |
Min. Marking Depth | 0.0002 in. (0.005 mm) |
Max. Marking Depth | 0.003 in. (0.08 mm) on a single pass |
Min. Line Width | 0.006 in. (0.15 mm) |
Precision | ±0.1 µm |
Required Operating Environment | <70% Humidity and 40–95°F (5–35°C) |
Required Operating Software | SeaCAD |
Components
Main Parts
- A. Main Tower—This houses the fiber laser source, its mainboard, and various connections.
- B. Galvo Lens Head—The high-speed galvanometer scanning head focuses the laser beam to a fine point, directing it to proper locations on the target material during engraving.
- C. Laser Cable—This transmits the laser beam from its source to the galvonometric lens.
- D. Worktable—This platform holds the target material, with optional positioning bars to ensure precise alignment.
- E. Height Adjustment Knob—This wheel moves the laser arm up and down for the correct alignment across different materials and thicknesses.
- F. Support Column—The support column holds the laser arm and includes a precise graduated rule for quickly adjusting height to work with different materials and thicknesses.
Main Tower
- A. Stepper Motor—This motor helps control attached rotary axes.
- B. Mainboard—This circuit board works with your software to control the laser.
- C. Mainboard Power Supply—This device draws 0.5A to convert standard electricity to 5V 3A power for the mainboard.
- D. Laser Power Supply—This device draws 6.8A to convert standard electricity to 24V 14.6A power for the fiber laser source.
- E. Galvanometer Power Supply—This device draws 2.5A to convert standard electricity to 15V 2A power for the scanning lens.
- F. Fiber Laser Source (Inside Casing)—This component creates the laser beam and transfers it to the fiber optic pathway to the scanning lens.
Connection Inputs
- A. Laser Cable—This transmits the laser beam from its source to the galvonometric lens.
- B. USB Cord Input—This port connects the device to your control computer.
- C. Interlock & Fan Cable—This cable input enables the option to power the interlock and exhaust fan of a protective covering.
- D. Foot Pedal Cord Input—This port enables optional pedal control of laser activation to free your hands for manual adjustment of the target material.
- E. Rotary Axis Cord Input—This port enables use of a rotary axis engraver with a 4-pin connection cable. (Compatible rotary axis devices are sold separately.)
- F. Power Cord Input—This 3-pin port connects to the device’s standard 3-prong power cord.
Power Buttons
- A. Emergency Stop—Because of the risk of fire and other hazards during engraving, this engraver includes a large and easy-to-reach emergency stop button near the control panel. Press it down to stop the laser instantly.
- B. Scan Head—Activates the mainboard inside the main tower and the galvanometer head inside the main arm. Insert your key and turn this first during startup and last during shutdown.
- C. Fiber Laser—Activates the laser source. Press this last during the startup and first during shutdown.
Control Computer
This fiber laser marker is controlled by the included SeaCAD software, which
must be installed on a compatible computer to direct the laser. See its
separate manual for full details on its components and use. Some features
which are particularly important to note include the following parameters and
controls:
- Speed—Specifies the speed of the beam in millimeters per second, with greater speed creating less contrast in the marked image.
- Power—Specifies the % of the machine’s rated power that will be used, with greater power creating greater contrast. Note again that running the machine at greater than 80% power will shorten its service life and 10–75% is recommended for most applications.
- Frequency—Specifies the laser’s frequency in kilohertz (kHz), with higher frequency producing a denser laser mark and darker engraving.
- Red (F1)—Tells the laser guidance to illuminate the current laser path.
- Mark (F2)—Fires the laser beam for testing and focus improvement.
Safety Information
Disclaimer
Your engraver may differ somewhat from those shown in this manual due to
options, updates, etc. Please contact us if your marking machine came with an
outdated manual or if you have any other questions.
General Safety Instructions
-
Use this laser marking device only in accordance with all applicable local and national laws and regulations.
-
Use this device only in accordance with this instruction manual and the manual for the engraving software included with it. Only allow this device to be installed, operated, maintained, repaired, etc. by others who have also read and understood both manuals. Ensure that this manual and the software manual are both included with this device if it is ever given or sold to a third party.
-
DO NOT operate this device continuously for more than 5 hours. Stop every 5 hours for at least
½ hour. -
DO NOT leave this device unattended during operation. Observe the device throughout operation and, if anything seems to be operating strangely, immediately cut off ALL power to the machine and contact either our customer service or your dedicated repair service. Similarly, ensure the device is FULLY turned off in the correct order after each use.
-
DO NOT allow minors, untrained personnel, or personnel suffering from physical or mental impairment that would affect their ability to follow this manual and the software manual to install, operate, maintain, or repair this device.
-
Any untrained personnel who might be near the device while it is in operation MUST be informed that it is dangerous and fully instructed on how to avoid injury during its use.
-
Always keep a fire extinguisher, water hose, or other flame retardant system nearby in case of accidents. Ensure that the local fire department’s phone number is clearly displayed nearby. In the case of a fire, cut electrical power before dousing the flame. Familiarize yourself with the correct range for your extinguisher before use. Take care not to use your extinguisher too close to the flame, as its high pressure can produce blowback.
Laser Safety Instructions
This machine uses an invisible laser. Used without care, it can cause serious
property damage and personal injury including but not limited to the
following:
- The laser will easily burn nearby combustible materials
- Some working materials may produce radiation or harmful gasses during processing
- Direct exposure to the laser will cause bodily harm including serious burns and irreparable eye damage As such,
- NEVER interfere with the laser beam.
- DO NOT place any part of your body under the laser lens during operation. Take measures to protect yourself from potentially reflected laser beams including the use of screens or personal protective equipment.
- NEVER attempt to view the laser directly without protective eyewear. Always wear safety goggles or glasses designed to filter the specific wavelength of your engraver’s laser with an optical density (OD) of 5+. As even seem-ingly matte materials can produce harmful reflected beams, care should be taken to keep anyone without protective eyewear from observing the machine during operation. EVEN WITH protective eyewear, do not stare or allow others to stare continuously at the laser beam during operation.
- DO NOT leave potentially combustible, flammable, explosive, or corrosive materials nearby where they could be exposed to the direct or reflected laser beam.
- DO NOT use or leave sensitive EMI equipment nearby. Ensure the area around the laser is free of strong electromagnetic interference during any use.
- ONLY use this machine as described in the Material Safety section of this manual. The laser settings and engraving process must be properly adjusted for specific materials.
- Ensure the area is kept free of airborne pollutants, as these might pose a similar risk of reflection, combustion, etc.
- NEVER use this marking machine with the fiber source’s housing opened, as the closed laser light path is necessary to prevent laser radiation leakage.
- DO NOT modify or disassemble the laser and do not use the laser if it has been modified or disassembled by anyone except trained and skilled professionals. Dangerous radiation exposure and other injury may result from the use of adjusted, modified, or otherwise incompatible equipment.
Electrical Safety Instructions
- ONLY use this device with a compatible and stable power supply with less than 5% fluctuation in its voltage.
- DO NOT connect other devices to the same fuse, as the laser system will require its full amperage. Do not use with standard extension cords or power strips. Use only surge protectors rated over 2000J.
- ONLY turn on the power to this device when it is well grounded, either via a firm connection to a 3-prong outlet or via a dedicated grounding cable firmly connected to the proper slot on the back of the main tower. Do not use with an ungrounded 3 to 2 prong adapter. The device’s grounding should be checked regularly for any damage to the line or loose connections.
- Turn the device on and off using its key and power buttons in the correct order. The mainboard, galvanometer, and laser have separate power supplies that are grounded in order. Activating everything at once, too quickly, or in the wrong order may send electrical current to an ungrounded component, causing short circuits and other electrical hazards.
- ONLY use this device with one hand at a time. The laser is powered by an extremely high voltage connection and placing two hands on the machine at one time during operation has the potential to create a closed circuit with the human body, resulting in electrical shock.
- The area around this laser marking device should be kept dry, well ventilated, and environmentally controlled to keep the ambient temperature between 40–95°F (5–35°C). The ambient humidity should not exceed 70%.
- Adjustment, maintenance, and repair of the electrical components of this device must be done ONLY by trained and skilled professionals to avoid fires and other malfunctions, including potential radiation exposure from damage to the laser components. Because specialized techniques are required for testing the electrical components of this marking system, it is recommended such testing only be done by the manufacturer, seller, or repair service.
- Unless otherwise specified, ONLY undertake adjustment, maintenance, and repair of the device when it is turned off and disconnected from its power supply.
Material Safety Instructions
- Users of this fiber marking machine are responsible for confirming that materials to be processed can withstand the heat of a class 4 laser and will not produce any emissions or byproducts either harmful to people nearby or in violation of any local or national laws or regulations. In particular, do not use this device to process polyvinyl chloride (PVC), teflon, or other halogen containing materials under any circumstances.
- Users of this fiber laser are responsible for ensuring that every person present during operation has sufficient PPE to avoid any injury from emissions or byproducts of the materials being processed. In addition to the protective laser eyewear discussed above, this may require goggles, masks or respirators, gloves, and other protective outer clothing.
- Users must exercise special caution when working with conductive materials as buildup of their dust and ambient particles may damage electrical components, cause short circuits, or produce other effects including reflected laser radiation.
This machine can be safely used with the following materials:
- Aluminum
- Brass
- Carbide
- Gold
- Silver
- Steel
- Stone, including Granite, Marble, etc.
- Titanium
- Tungsten
This machine can be used with some other metals, hard plastics, and other materials with some care. For other materials, if you are unsure about its safety or laserability with this device, seek out its material safety data sheet (MDS). Pay espe-cial attention to information about safety, toxicity, corrosiveness, reflectivity, and reaction(s) to high heat. Alternative-ly, contact our support department for further guidance.
See §4.3 for the recommended parameters for the most commonly engraved materials.
This machine CANNOT be used with the following materials or with any materials which include them:
- Artificial Leather containing Hexavalent Chromium (Cr[VI]), due to its toxic fumes
- Astatine, due to its toxic fumes
- Beryllium Oxide, due to its toxic fumes
- Bromine, due to its toxic fumes
- Chlorine, including Polyvinyl Butyrale (PVB) and Polyvinyl Chloride (PVC, Vinyl, Cintra, etc.), due to its toxic fumes
- Fluorine, including Polytetrafluoroethylenes (Teflon, PTFE, etc.), due to its toxic fumes
- Iodine, due to its toxic fumes
- Paper and Paperboard, due to their high flammability when exposed to the concentrated laser
- Phenolic Resins, including various forms of Epoxy, due to their toxic fumes
- Wood, including MDF, Plywood, Balsa, Birch, Cherry, Oak, Poplar, etc., due to its high flammability
Installation
Installation Overview
A complete working system consists of the fiber laser source, the laser arm
with the galvanometer lens, the laser key, a computer (not included) with
engraving software (included), and all applicable connection cables. A support
column and workbed come included to assist your work. Users can also configure
other additional accessories (such as a rotary axis) to suit their needs.
Use only the hardware, wiring, and power sources that came with or are compatible with this device. Installing equipment that your device is not designed to work with can lead to poor performance, shortened service time, increased maintenance costs, property damage, and personal injury.
Please note the specific requirements of your system’s installation. Every customer must understand these notes before installation to execute a proper setup and achieve safe laser performance. If you have any installation questions or problems, contact our technicians and customer support team. Any auxiliary equipment must be adjusted to the base machine. Queries may be directed to the dealer or manufacturer of such equipment.
Location Selection
Prior to assembling your fiber laser marker, select an appropriate location
for its use. Be sure that it meets all of the requirements discussed in the
Safety Information above. The location should be stable, level, dry, and
climate controlled to ensure an ambient temperature 40–95°F and an ambient
humidity under 70%. In particular, the temperature and humidity together
should not be close to the dew point. It is also advisible to use a windowless
room or to use blinds and/or curtains to avoid exposure to the potential
additional heat of direct sunlight. The location should be free of dust and
other airborne pollutants and well ventilated enough to process any fumes
produced by the engraving process in accordance with all applicable laws and
regulations. Depending on the materials to be processed, this may require
construction of a dedicated ventilation system. It should be away from
children; combustible, flammable, explosive, or corrosive materials; and
sensitive EMI devices. The power cord should be plugged into a compatible and
stable power source via a grounded 3-prong outlet. No other item should be
drawing current from the same fuse. There should be fire-fighting equipment
nearby and the local fire department’s phone number should be clearly
displayed. It is highly recommended to have an extra work table nearby in
order to avoid placing objects on or directly adjacent to the machine, which
could become a fire or laser hazard
Electrical Grounding
This device employs a class 4 laser. As discussed in the Safety Information
above, it is extremely high voltage and potentially dangerous, so users must
securely ground it to avoid the buildup of static electricity. Using a
standard 3-prong outlet will provide sufficient grounding. If you do not have
access to a 3-prong outlet, you MUST use the grounding cable and ensure its
proper connection. The far end of the cable should be securely connected to a
metal rod driven at least 8 feet (3 m) deep into soil located at least 5 feet
(1.5 m) from the machine. The resistance along the line should be no greater
than 5Ω.
Poor grounding WILL cause equipment failure and create a serious electrical shock hazard. The manufacturer and/or seller bear(s) no responsibility and assume(s) no liability for any damage, accidents, or injuries caused by bad grounding connections.
Assembly Instructions
-
Step 1. Install the support column onto the worktable using the four mounting holes and the provided bolts.
-
Step 2. Install the laser arm onto the support column using the provided bolts.
Turn the knob on top of the support column to adjust the height of the laser arm to about 24 cm, as marked on the column’s ruler. This will position the lens to be nearly in focus with most common materials. -
Step 3. Make all necessary connections between the various components.
-
Step 4. The positioning bars can be installed onto the worktable and left in place for all your projects or can be moved around to suit different projects. Simply place the bars over the holes that will form the outer edge of the target material and fasten them into place with the provided bolts.
Control Computer Installation
See the separate engraving software manual for details on the requirements for
the control computer. The control computer should not be placed more than 15
feet (4.5 m) away from the fiber laser marker in order to avoid possible
interference to the signal in its line. Familiarize yourself with your
software’s image design features and laser control settings before beginning
operation of the laser itself.
Operation
Operation Overview
Operate this laser marking machine only in accordance with all the instructions provided in this manual. Failure to follow the proper guidelines detailed here can result in property damage and personal injury.
This section will address only some of the options and features provided by the operation software. Before beginning to use the machine, make sure that you have read this entire manual (particularly the Safety Information above), the separate software manual, and any and all warnings provided on the machine itself.
General Operation Instructions
-
Step 1. Load or create a design in SeaCAD.
-
Step 2. Put on your protective eyewear. Ensure that anyone else who might bet exposed to direct or reflected laser beams is also wearing protective eyewear as described in §2.4.
-
Step 3. Turn on the laser marker by inserting your key and turning it and then pressing the Fiber Laser button.
Activating the laser key and buttons out of order may cause electrical hazards as the separate power supplies are grounded in order. Do not activate everything quickly. Give each power supply time to come on line, activating its fans. 3 seconds is sufficient.
To reduce the risk of electric shock, once the engraver is on, try to touch its components with only one hand at a time. -
Step 4. If you previously disconnected the control computer, reconnect it via the USB cable now. If your computer is already connected and SeaCAD is already running, restart it now to establish a connection between the com-puter and the laser’s control board.
-
Step 5. Customize your contrast and engraving depth by adjusting the engraving parameters in SeaCAD. To darken an image, use a higher frequency setting. To lighten it, use a lower one. To increase engraving depth, increase the amount of energy per unit area by reducing the speed parameter or increasing the laser’s power or the number of loops. Engraving too deep, however, reduces image quality, especially for coated materials. Again, constantly using settings over 80% will shorten the expected service life of your laser.
Resolution should usually be set to 500 dots per inch. Reducing your image resolution can be helpful in some cases, reducing flaming and increasing the energy of the pulse in a way that improves the quality of the resultant image in some materials such as some plastics. -
Step 6. Activate the laser guidance system by pressing Red or hitting F1 in SeaCAD. The design should be displayed in red light on the worktable, showing where the laser will fire.
-
Step 7. Place an expendable piece of the material to be engraved in the location shown by the laser guidance. Do not use a different target as the galvanometer lens automatically focuses at different heights for different materials. Being careful that no part of your body is near the worktable or laser path, press Mark or hit F2 in SeaCAD to fire the test laser. Alternatively, you can activate the laser by using the foot pad.
-
Step 8. The laser is invisible but will create a buzzing noise and sparks and begin engraving when it is correctly focused on your test material. If no sparks are emitted, the laser is out of focus. Continue to fire it while adjusting the up or down using its height adjustment knob. Small, consistent sparks will be emitted at the marking point when the beam is correctly in focus. Take a note of the correct height for future reference.
-
Step 9. Replace the test material with the actual material. Use the foot pad or press Mark or hit F2 in SeaCAD to engrave your pattern. Again, do not stare at the laser in operation even with protective eyewear. Watch for possible issues like sparks or fires, however, and be prepared to quickly extinguish a fire if necessary.
-
Step 10. Examine the quality of your first run and adjust the laser parameters in SeaCAD as necessary to create your desired effect. The foot pedal is particularly useful for continuous or repeated operation of the laser once you’ve settled on your design and its ideal parameter settings. You can also achieve more control of the marking process by reducing the laser’s speed and using the foot pad.
-
Step 11. When you have finished engraving your design, close SeaCAD and then turn off the laser marking machine
by pressing the Fiber Laser button and then turning your key and removing it. -
Step 12. Cover the galvonometer lens and fully clean the workbed. For best results, disconnect your fiber marking machine from its power supply between uses. Unplug it or turn off its intermediary surge protector.
Instructions for Specific Materials
When engraving a new material, it can be helpful to engrave a test matrix of
small boxes produced with various speed, power, and frequency settings to home
in on the exact effect that you are looking for. To speed the process, here
are some general guidelines for commonly engraved materials. Again, however,
these are only guidelines for your conve-nience and it is the responsibility
of the user to consult material safety data sheets and other sources to ensure
the safety of working with various materials and setups. Some of the materials
listed will require additional workspace and personal protective equipment in
addition to this engraver:
Metals
When engraving metals, generally use high power, a low frequency, and low to
medium speed settings. To avoid using your marker at greater than 80% power
for extended periods, you can also get similar effects by reducing the power
somewhat while also increasing the number of passes or decreasing the
engraving speed. Be mindful that some metals will produce conducting,
reflective, and/or toxic dust. Softer metals naturally produce more dust
during engraving, while harder metals can require higher power settings that
also produce more dust. In addition to the risk to the user’s skin and eyes,
there may be enough dust produced (especially for repetitive industrial
applications) that a full ventilation system is required to address the
problem. Similarly, operators and others in the work area may need to use
breathing PPE such as masks and respirators.
Aluminum: Bare aluminum requires a somewhat higher frequency than other metals
and will never produce a strong black mark similar to those created by
engraving steel. When darker marking is required, consider employing
anodization or producing a deep engraving that can be darkened by using black
epoxy or other filler. Anodized aluminum requires a little more speed but a
very low frequency.
Powder Coated Metals: Metals with a powder coating usually require a very high
frequency and, for best results, at least 3 passes to remove the coating and
polish the bare lower layer.Precious Metals: Gold and similarly soft metals
should be engraved with less power but a moderate speed. Silver and other
semidurable metals are best engraved at a slightly higher power and slightly
slower speed, but still not at the same power and speed as steel or aluminum
Plastics
When engraving plastics, generally use low power and high speed settings.
Marking and engraving with too much power or at too low a speed can
concentrate too much energy at the point of contact, causing the plastic to
melt. Among other problems, this may produce poor engraving quality, noxious
fumes and even fires.
Stone
When engraving various kinds of stone, generally use moderate power and speed
at low frequency. As with ceramics and metals, be mindful of the dust created
(especially for repetitive industrial applications) and take similar measures
to ensure the safety of users and others in the work area.
Maintenance
Maintenance Overview
Unless otherwise specified, ONLY perform adjustment and maintenance of this device when the power is turned off and the power supply has been disconnected. ONLY allow trained and skilled professionals to modify or disassemble this device.
Regular Maintence Procedures
- Keep the workroom clean and dust-free at all times.
- Ensure the device is fully powered off when not in use.
- Cover the galvanometric lens when it is not in use.
- Clean the worktable after use with a cloth wetted with greater than 75% rubbing alcohol. NEVER clean this device with abrasive or caustic cleansers, with aerosol sprays, or with enough water to enter any electrical component. Always allow surfaces to fully dry before further use.
- If removing dust from the device’s vents using a vacuum, ONLY use the lowest power setting to avoid damage to internal components.
No other servicing should be done by the operator. Do not attempt to service or replace other parts yourself.
Troubleshooting Guidance
Potential Problems | Possible Solutions |
---|
No Laser Output
| Correct the focus by adjusting the height of the laser arm.
Correct the software parameters if they are invalid or mistaken.
Have a technician fix or establish the connection between the laser and the
mainboard.
Have a technician fix or establish the connection between the laser and its
power supply.
If either the fiber laser source or its power supply have worn out, have a
technician replace them.
No Engraving despite Laser Output
| Confirm that the material can be safely engraved with this device.
Correct the focus by adjusting the height of the laser arm.
Adjust the software parameters to create greater intensity.
Have a technician check the control panel, scanning lens, and its power
supply. Correct any problems or replace the part.
Other Laser Errors
| Have a technician check the fiber laser source and the mainboard. Correct any problems or replace the part.
Disposal Instructions
Electrical products should not be disposed of with household products. In the
EU and UK, according to the European Directive 2012/19/EU for the disposal of
electrical and electronic equipment and its implementa-tion in national laws,
used electrical products must be collected separately and disposed of at the
collection points provided for this purpose. Locations in Canada and the US
may have similar regulations. Contact your local authorities or dealer for
disposal and recycling advice.
Contact Us
Thank you for choosing our laser equipment for your home or shop! For a
.pdf copy of the latest version of this manual, use the appropriate app on
your smartphone or other device to scan the QR code to the right. Come join
the OMTech community at our official laser group on Facebook or visit the
company forums at omtechlaser.com! Check our YouTube
channel for helpful hints and instructional videos. If you encounter any
problem regarding your engraver, do not hesitate to contact customer service
with your order number at help@cs-supportpro.com or
techsupport@omtechlaser.com. Our teams will
respond within 24 hours to make things right. You can also reach us Monday to
Friday at 949-539-0458 between 8 am and
4:30 pm PST. Thank you and we hope you will choose us again for all your laser
needs!
References
- Laser Engraver and Cutting Machines - OMTech Laser
- Transparent outsourced web hosting tech support |SupportPRO