Kitette Q4 Electric Dehumidifier for Bathroom User Manual

Kitette Q4 Electric Dehumidifier for Bathroom User Manual

POINTS FOR ATTENTION

Before using, please read this user manual carefully and keep it for future reference.

Warning

1. Do not let water or other liquids or flammable cleaning agents enter the product to avoid electric shock and fire.
2. Do not spray any combustible materials such as insecticides or perfumes around the product.
3. Before connecting the product to the power supply, please check whether the voltage used by the product is consistent with the local power supply voltage.
4. This product cannot replace the range hood used for normal ventilation, daily vacuuming or cooking.
5. Be sure to place and use this product on a stable, flat and level surface.
6. Do not insert fingers or objects into the air outlet or air inlet to prevent the product from physical damage or malfunction.
7. Before using this product, please read this user manual carefully and keep it in a safe place for future reference.

PRODUCT OVERVIEW

Components

INSTRUCTIONS

Power Button

1. Take out the power adapter and connect the product to the socket.
2. Press the power button to turn on the dehumidifier.
3. When the water tank reaches its capacity, please drain the water and install the empty water tank back to its position. The unit can continue its operation.
4. Press the power button to shut down.

Control panel

  Light Button

ONLY OPERATE LIGHT WHEN THE POWER BUTTON IS ON.

1. The light will automatically turn on after pressing power button.
2. 1st Press the light button to set your preferred color.
3. 2nd Press the light button to turn off the light function.

*The light will flash in order to remind you the water tank is full.

METHODS OF POURING WATER

1. The humidification capacity of this dehumidifier is about 450ml per day, and the maximum capacity of the water tank is 1.4L.
2. When the water tank is full, the indicator light will flash and it will automatically stop working. At this time, please press the power button to turn off, and then slowly take out the water tank, do not tilt the water tank, otherwise the water will overflow; slide the water tank cover back to pour out the water.
3. After pouring the water, put the water tank back to its original position, press the power button to turn on, and the product will start working again.
4. When you do not need to dehumidify, please press the power button to shut down, take out the water tank, pour water, and put the water tank back in place, waiting for the next identification.

MAINTENANCE

Cleaning

Please confirm that the product has been pressed the power button, and unplug the power cord, gently wipe the surface with a soft cloth dust and dirt on the surface and air inlet. If you want to clean the water tank, remove the water tank and turn on the water the lid can clean the water tank.

Precautions

1. When humidification is not needed, press the power button and unplug the power cord.
2. Do not put the adapter in a humid or humid place, and keep it well ventilated.
3. Remember not to block the air inlet and outlet.
4. Put the product in a horizontal place, don’t tilt it to prevent water leakage.

SPECIFICATION TABLE

WARRANTY

For questions about our warranty or to look at our other products, please contact email us@customerafterservice.com.

Thank you very much for using our products.
Please read the user manual carefully before use, and keep it for future reference.

TECHNICAL REQUIREMENTS

1. Color box &paper card: material and size should be according to document requirements, the size of the finished product deviation within 2-3mm requirements;
2. Carton: material and size should be according to document requirements, the size of the finished product deviation within plus 5-10mm requirements;
3. PE foam: the bonding place of PE foam should be smooth, the glue should be even, the size of the finished product deviation within 2-3mm requirements;
4. Manual, warranty card, label, album and other printing materials must meet the inspection requirements of the quality department;

* Details of all packaging materials can be compared with: Inspection guide for incoming materials of packaging cartons – document No.: YWT-ZY-PZ-26

1. The printed contents, patterns and fonts shall meet the requirements of drawings or sealed samples, and the patterns shall be clear, full, no decolonization and obvious overflow edge; and the position shall be accurate, horizontal deflection is not allowed to exceed 5mm, pattern shall be consistent color, good ink adhesion, and not decolonizing with fingers;
2. Packing materials must have protective measures and are not allowed to damage their outer surface due to packaging and transportation.

us@customer-afterservice.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>