cbi 600-000-000-050 Camp Table Instruction Manual

: June 3, 2024
: cbi

Table of Contents

What is included
Installation
Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)
6 x 3/8 Flat Head Phil Mach Screw
6-32 Steel K-Lock Nuts

cbi 600-000-000-050 Camp Table Instruction Manual

IMPORTANT

THANK YOU for purchasing this CBI product. Please read through this entire document before proceeding with installation. If you are not confident in your mechanical skills, please seek the help of a professional to perform the installation. Check your packages immediately upon arrival to ensure that everything listed is included, and to check for damage during shipping. If anything is missing or damaged, or if you need technical assistance with any aspect of this installation, call CBI at 208-528-0664 as soon as possible.

What is included

IMPORTANT

If your CBI product comes as unpainted, bare steel or aluminum. You will want to either powder coat or paint prior to final installation, however it is very important to PRE-INSTALL the unpainted product first, following these instructions, BEFORE painting or powder coating any of the components! This will ensure that all parts are correct and any incidental trimming or drilling will have been done prior to coating. Also, it will give you a practice run to familiarize yourself with the process, to lessen the likelihood of damaging the finish during final installation.

CBI Off Road is NOT RESPONSIBLE
for paint or powder coating costs, damage to paint or powder coating, or costs associated with inadvertently painting
or powder coating components that are defective or were shipped or assembled in error. It is the customer’s responsibility to pre-install and verify that all parts are correct prior to paint or powder coat.

Hardware:

10 1/4”-20 Hex Thin Nylon Insert Lock Nut
8 1/4”-20 x 1/2” SS Button Head
2 1/4”-20 x 3/4” SS Button Head
4 #6 x 3/8 Flat Head Phil Mach Screw
4 #6-32 Steel K-Lock Nuts
2 Nylon Bearings
4 Cable Ends
1 Catch Spacer
1 Ball Catch
2 Cables
1 set L/R Table mounting brackets
1 Table

Installation

Start by installing the L/R Table mounting brackets “K”. These brackets ar mounted using the Button head bolts “B” and nylock nut “A” .

Drivers Side

Note:
There is a Top And Bottom the the mounting brackets.

IMPORTANT

Do not tighten these brackets at this point. Tighten them down just enough that you can still freely move the brackets.

Passenger Side

1/4”-20 Hex Thin Nylon Insert Lock Nut
1/4”-20 x 1/2” SS Button Head

Measurements

Nylon Bearings

Insert the nylon bearings into the bottom holes on the table
Use the longer button heads “C” to attach the table to the bottom hole of the mounting brackets.
- 1/4”-20 Hex Thin Nylon Insert Lock Nut
- 1/4”-20 x 3/4” SS Button Head
The #6 machine screws “D” and #6 lock nuts “E” will be used to mount the ball catch to the table and swing arm. Just hand tighten this hardware for now. (you can discard any hardware included in the ball catch bag)
Use the #6 machine screws “D” and #6 lock nuts “E” along with the spacer “H” to mount the catch on the sing arm as shown.
With all the hardware installed you can now squared the table with the brackets. Adjust until the ball catch lines up properly and tighten all of the hardware.
- Ball Catch
- Catch Spacer
- 6 x 3/8 Flat Head Phil Mach Screw
- 6-32 Steel K-Lock Nuts
The cables will need to be cut to length. The cables should be cut to roughly 15.5” in length (not including the cable ends).
Strip the coating back from the ends of the cables. Strip back about 3/4”.
Secure the cable ends “G” to each end of the two cables. This can be done by crimping the cable ends as shown in image 8.

Alternatively, you can heat the cable end and melt solder into the cable ends. Insert the cable intothe molten solder before it solidifies. (see 8a- 8b)

Note:
Double check the length before completing the cables. You can check by holding the table 90° to the swing arm and check the cable length.
- Cable Ends
- Cables
Install the completed cables to the top hole of the mounting brackets “K” .
The other end attaches to the top/front of the table.

These connections should only be snugged tight to allow the cable ends to move freely in the mount.
- 1/4”-20 Hex Thin Nylon Insert Lock Nut
- 1/4”-20 x 1/2” SS Button Head