DK ELECTRONIC MP-6 2.4G Digital Microphone Instruction Manual

ELECTRONIC MP-6 2.4G Digital Microphone
Instruction Manual
2.4G Digital
Microphone Instructions

Transmitter Of Microphone Key interface indication.

|
---|---

1. On/Off button:
   Short press: power check ( the white light on the middle battery icon will blink.
   Long Press 2 seconds: Turn on/off

2. Mute Button:
   Short press: The microphone is muted (at the same time the microphone icon is steady red.)
   Long press 5 seconds: Enter pairing mode(Connection icon indicator blinks in short intervals)

3. Inside Microphone:

4. Indicator Description:
   Indicator light-Blue:
   Unpair: Blink at long intervals.
   Connected: steady on.
   Pairing: Flash.
     Power light:
   Charging: Steady on a red light.
   Turn on: Steady on white light.
   Power check: the white light blinks several times, flashing 1 grid of power once, flashing 2 grids of power twice, a total of 4 grid power.
   Low power warning: the red light blinks.
   Microphone signal light:
   With sound: the green light is on.
   Without sound: the green light is off.
   Mute mode: The red light is steady on.

5. USB Type-C charging interface.

6. TES external microphone interface.

The receiver of the Microphone Key interface indication

|
---|---

1. On/Off button:
   Short press: power check ( the white light on the middle battery, the icon will blink.
   Long Press 2 seconds: Turn on/off

2. Volume button
   Short press: Output volume selection (High-Medi­ ume-Low), the default volume is medium. It will blink twice in different colors. Long press 5 seconds:
   Enter pairing mode(Connection icon indicator blinks in short intervals)

3. Earphone output interface.
   

4. Noise control buttons:
   Short press: Turn on/off the noise control button(in open mode, the microphone indicator on the receiving end will turn yellow.)

5. Indicator Description:
     Indicator light-Blue:
   Unpair: Blink at long intervals.
   Connected: steady on.
   Pairing: Flash.
   Power light:
   Charging: Steady on a red light.
   Turn on: Steady on white light.
   Power check: the white light blinks several ( times, flashing 1 grid of power once, flashing 2 grids of power twice, a total of 4 grid power.
   Low power warning: the red light blinks.
   Microphone signal light:
   With sound: the green light is on.
   Without sound: the green light is off.
   Noise reduction on The yellow light is on.
   The volume choice:
   High Volume–Blinking red twice
   Medium Volume–Blinking yellow light twice
   Low volume–Blinking green light twice

6. USS Type-C charging interface.

7. TRS audio output interface.

The Application Installation

1. Long press the power switch, and the power will be automatically paired. When the connection indicator is steady on, it can be used.
2. The transmitter of the microphone can be clipped on the collar of the user or connected to an external microphone.
3. Fix the receiver of the microphone to the camera hot-shoe holder or mobile phone bracket
4. Connect one end of the 3.5mm TRS output audio cable to the TRS interface of the receiver and the other end to the MIC input interface of the camera. If it is a mobile phone, select the 3.5mm TRS output cable of 3 to 4, some smartphones also need an adaptor.

Specification

Transmission band:2400MHz-2483.5Mhz
Modulation mode: frequency hopping/digital FSK (GFSK)
Transmission power: 10dbm
Receiver sensitivity:-85dbm
Microphone pick up mode: Omni-directional
Audio frequency response:100-20Khz+-3dB
Display mode: LED
Power supply: The built-in lithium is charged through a standard DC 5V with a Type-c interface.
Time of endurance:> 10 hours
The input I Output interface:3.5mm TRS
Work temperature:-5degree -+50degree
Demensions:41,248.718.4mm
Weight:26g2

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>