REBEL ZAB0120 STUNT SCOOTER User Manual
- June 5, 2024
- Rebel
Table of Contents
REBEL ZAB0120 STUNT SCOOTER
Introduction
AN IMPORTANT MESSAGE TO PARENTS: This manual contains important information. For your child’s safety, it is your responsibility to review this information with your child and make sure that your child understands all warnings, cautions, instructions, and safety topics. We recommend that you periodically review and reinforce the information in this manual with younger riders and that you are required to inspect and maintain your child’s scooter to ensure their safety.
GENERAL WARNING: Scooter riding can be a hazardous activity. Scooters can, and are intended to move and it is, therefore, possible to get into dangerous situations and/or lose control and/or fall. If such things occur you can be seriously injured. According to the European Scooters Standards EN 14619:2004, this product is designed and commercialized for use in sporting events or for physical training.
LIKE ANY OTHER MOVING PRODUCT, USING A SCOOTER CAN BE A DANGEROUS ACTIVITY AND MAY RESULT IN INJURY EVEN WHEN USED WITH PROPER SAFETY PRECAUTIONS. USE AT YOUR OWN RISK AND USE COMMON SENSE.
- Always wear safety equipment such as helmet, knee pads and elbow pads. Always wear a helmet when riding your scooter and keep the chinstrap securely buckled.
- Always wear shoes. Keep shoelaces tied and out of the way of the wheels.
- Always maintain a hold on the handlebars.
- Avoid sharp bumps, drainage grates, and sudden surface changes.
- Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other debris. Wet, slick or uneven and rough surfaces may impair traction and contribute to possible accidents.
- Do not ride a scooter in wet weather, mud, ice, puddles or water. Scooters are intended for use on solid, flat, clean and dry surfaces such as pavement or level ground without loose debris such as rocks or gravel.
- Scooters are meant to be used only in controlled environments free of potential traffic hazards and not on public streets. Never use near steps, sloped driveways, hills, roadways, alleys or swimming pool areas.
- Do not ride at night or when visibility is impaired.
- Brake will get hot from continuous use. Do not touch after braking.
- Avoid excessive speed associated with downhill rides.
- Adults must assist children in the initial adjustment procedures to assemble the scooter.
- Obey all local traffic and scootering laws and regulations.
- watch out for pedestrians.
- Check and secure all fasteners before every ride.
- Replace worn or broken parts immediately.
- Do not allow exceed 100 kilograms on the stunt scooters.
- Do not allow children under age eight to use the stunt scooter. All children and preteens should ride with adult guidance at all times.
- Rider weight does not necessarily mean a child’s size is appropriate to fit or maintain control of the scooter. A parent’s decision to allow his or her child to ride this product should be based on the child’s maturity, skill and ability to follow rules.
- Trick riding can over stress or damage any product, including this scooter, and the rider assumes all risks associated with high-stress activity.
WARNING: ALWAYS INSPECT SCOOTER PRIOR TO RIDING
Properly inspecting and maintaining your scooter can reduce the risk of
injury.
MAINTENANCE: When used properly, the ball bearings are essentially maintenance-free. The scooter has been equipped with high-quality ball bearings. These ball bearings are only to be cleaned externally. If they should be especially soiled on the outside, they can be carefully cleaned with a cotton swab at the time of replacing the casters. In doing so, no dirt may get into the encased area.
IMPORTANT: The ball bearing could produce noises when riding over a wet surface. This is because moisture could cause the lubricant to be washed out of the ball bearing, which would then run “dry” this would produce noise when riding. New ball bearings must then be inserted. No modification other than to the manufacturer’s instructions shall be made.
PRODUCT DESCRIPTION
- Handlebar
- Grips
- Clamp
- Front-wheel
- Deck
- Foot brake
- Rear wheel
ASSEMBLY
- Push the handlebar column onto the fork until it bottoms out on the fork headset lock nut.
- With the front wheel pointed straight ahead, the handlebar square to the front wheel and the screws at the clamp facing the deck, securely tighten the clamp with the included hex wrench.
WARNING: Failure to properly install and tighten the clamp may cause the rider to lose control and fall.
HOW TO RIDE
Place one foot on the deck, push forward with the other foot. Steer. For
enhanced cornering, lean slightly into the direction of the turn.
For controlled stops, apply the brake by stepping on the rear brake. It is
recommend to practice applying the brake at various speeds and in an open area
free from obstructions before riding your stunt scooter around others.
WARNING: Wheelies and other stunt-type riding reduce your ability to maneuver and control your scooter. Take the necessary precautions, such as wearing appropriate protective gear and practice in an area safe for stunt riding and free from obstructions.
WHEELS AND BEARINGS
Under normal circumstances and conditions, scooter wheels and wheels bearings are maintenance free. Nonetheless, it is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for proper tightness and bearings for side-to-side play and loose parts. When a wheel bearing develops pay, this is an indication of excess wear and replacement is necessary. Replace immediately with wheels preferably. Worn wheels/bearings are considered normal wear-and-tear and are not covered by the scooter warranty. Wheels other than genuine this stunt scooter wheels may not be compatible with our stunt scooter. The use of anything other than genuine stunt scooter replacement parts may affect your safety.
CLEANING YOUR SCOOTER
Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners or solvents as they may damage the surfaces. Do not use alcohol-based or ammonia-based cleaners as they may damage or dissolve the plastic components or soften the decals or decal adhesive.
SPECIFICATION
General
- Dedicated for ages 8+
- Steel handlebar and TPR grips with grooves
- 360° handlebar
- Foot brake
- Non-slip deck
- Solid and lightweight construction
Deck
- Type: one-piece
- Dimensions: 360 x 110 mm
- Material: reinforced aluminum 6061
- Headtube angle: 82°
- Headset type: integrated
- Maximum load: 100 kg
Handlebar
- Type: Y-bar, one-piece
- Clamp: triple ,standard, aluminum
- Material: steel
- Height: 650 mm
- Width: 550 mm
- Outer diameter: 32 mm
- Inner diameter: 28 mm
Fork
- Type: threaded
- Material: steel
Wheels
- Material: PU
- Diameter: 110 mm
- Width: 24 mm
- Hardness: 82A
- Core: aluminum, spoked
- Bearings: ABEC-9
Physical parameters
- Weight: 3,2 kg
- Dimensions (length x width x height): 670 mm x 550 mm x 880 mm
- In set: 2x hex wrench, user’s manual
LEARN MORE
For more information on this device visit:
www.rebelelectro.com.
Read owner’s manual carefully before using your device.
Visit www.rebelelectro.com website for more
products and accessories.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or Its literature,
indicates that It should not be disposed with other household wastes at the
end of its working life. To prevent possible harm lo the environment or human
health from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract This product should not be mixed with
other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400
Miętne.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>