DAICH LX-SSGU-CA-40 Lux Rock Solid Surface Granite Countertop Kit Instructions

DAICH LX-SSGU-CA-40 Lux Rock Solid Surface Granite Countertop

Welcome to LuxROCK, the revolutionary new patent-pending stone coating system that delivers a whole new way to enjoy authentic, luxuriously smooth stone countertops, tables and more – at a fraction of the cost.

Follow these directions carefully for best results — and also follow safety precautions on all coating containers during use. The Primer Coat – is the first step of your new LuxROCK™ finish. It adheres well to laminate, wood, concrete and Daich Coatings ElastoLock® and creates an optimal bonding surface.

SURFACE PREPARATION

The surface must be clean, dry and in good repair.

1. If applying to laminate, the surface must be washed and degreased thoroughly.
2. If applying to a wood tabletop or concrete, the surface must be clean. If a previous coating exists, it must be in sound condition or otherwise must be removed.
3. For tile countertops, apply one thin coat of ElastoLock® as an intermediate bonding coat.
4. Protect adjoining surfaces (cabinets, fixtures,etc.) with painter’s masking tape, plastic or old newspaper.
5. Protect the floor around the countertop area with heavy cardboard or a drop cloth.
6. If installing LuxROCK around the existing sink edge and faucet fixtures, tape mask cleanly around all edges, to guard against coating contact.
7. Alternatively, for the easiest installation (especially if you ever wish to install new faucets or sink) we recommend lifting up a few inches – or removing – the sink and faucet fixtures prior to
8. LuxROCK installation for completely open access. Once complete, the sink and faucets can be dropped back down and refastened over top of your new stone surface — just like any other professional countertop installation.

APPLICATION

(Stir Primer thoroughly before use)

1. Use the 1” brush from the kit for tight areas as well as corners, along edges, etc. Wash the brush immediately after use.
2. Roll on one thin, uniform coat of Primer over the rest of the entire countertop or table surface with the enclosed 4-inch roller. Wash the roller after use.
3. Spot-apply Primer to any areas which exhibit “show through” of the underlying surface.
4. Let the surface dry for one to two hours before proceeding with the application of Step 2, the Stone Coat.

The Stone Coat is the main component of the LuxROCK Finish System. Its stone composition brings both strength and stunning granite elegance to your surface.

MIXING: Prior to use, the Stone Coat must be mixed thoroughly. Use the enclosed stir stick, being sure to stir from the bottom up to disperse any settled material at the bottom of the can. A drill mixer attachment is also an excellent stirring option.

The surface must be clean, dry, in good repair, and pre-coated with the enclosed Primer Coat from step one. Two applications of the Stone Coat must be applied. Allow at least 3 – 4 hours between coats (longer in cool or damp conditions).

1. Use the 1” brush from the kit to apply Stone Coat into corners, along edges and tight areas, around faucets, etc.. Brush it down flat and thin as you go.
2. Next, take the enclosed 4” brush and continue application across the raised backsplash piece (if present) and the rest of the countertop. Apply in a flat, uniform coat about 1/16” thick. Pass the brush over the wet material several times to fully distribute the material, remove brush marks and lock it down. The smoother the coating is applied, the more your new countertop will look like a polished granite surface.
3. For uniform continuous results, always work wet-in-wet. If you need to leave the room briefly, spray mist the leading edges with water (using the enclosed spray bottle) to keep them moist.
4. To apply over the bull nose or straight front edge of the countertop, just follow the contours with your brush. The Stone Coat will grab onto the primer. Be sure to leave the coating as smooth as possible. Continue in this manner until complete.
5. After several hours, apply a second coating the same way.

SANDING THE DRY STONE LAYER

With both coats applied, allow 24 hours to cure, and then proceed with the sanding of the surface.

1. Use the enclosed 120 grit sandpaper, followed by the enclosed 180 grit sandpaper to shave down any remaining roughness.

IMPORTANT: Your goal is to sand the surface FLAT prior to application of the clear coats that follow.

NOTE: There will still be soft, very light texture when sanding is complete. Do not worry about that, as it will be completely covered by the following epoxy layer. Just get it relatively smooth and flat. Sanding can be done by hand, but using a random orbital sander is highly recommended for the easiest results. LuxROCK’s decorative mineral ingredients are present throughout the coating, so don’t worry about removing LuxROCK’s beauty during sanding. Just be sure not to sand back down to the primer or underlying countertop.

1. WEAR THE ENCLOSED DUST MASK and vacuum all sanding dust thoroughly to ensure a clean, dust-free surface.m If possible, connect the sander to a vacuum to minimize dust during use.
2. Wipe down the surface several times with a very damp (not dripping wet) cloth to pick up any remaining fine dust. When complete, proceed with STEP 3.

StoneSet is a 2-part penetrating epoxy formula that integrates with your new stone layer to maximize hardness and smooth feel.

MIXING COMPONENTS: Keep in a cool place prior to use. PARTS MUST BE FULLY BLENDED FOR THREE MINUTES BEFORE APPLICATION. Pour full contents of “Part-B” into “Part-A” in original packaging or another suitable mixing container. Mix well for three minutes with the enclosed stir stick.

IMPORTANT: USE ONE FULL STONE SET EPOXY KIT PER 20 SQ.FT. for a thicker, more robust application. Apply uniformly.

SURFACE PREPARATION

The surface must be clean, dry, and DUST FREE. A dust-free surface will help ensure a clear, residue-free final finish.

1. Use a vacuum to thoroughly remove all loose dust from your countertop surface.
2. Next, wipe the surface with a thoroughly damp (not dripping wet) lint-free cloth to remove fine dust.
3. To avoid bonding of hardware to the countertop, sinks and faucets should be well masked off – or loosened and lifted a few inches off the coating surface – prior to StoneSet application.
4. Apply painter’s tape along the underside of the countertop corner or under the bull-nose. Remove tape two hours after application to remove any hanging droplets.

APPLICATION: Wear enclosed latex gloves during use. Avoid contact with eyes and skin. The surface must be smoothly sanded, dry, and dust-free before application of StoneSet coating.

1. Use the 1” brush from the kit to brush the coating into corners, along edges, and tight areas – and across the attached raised backsplash if applicable. Brush out any pooled coating at the bottom of the backsplash.
2. For the remaining flat top, pour down manageable 3 – 4” diameter puddles of StoneSet starting at one end of the surface and work your way across. Using the enclosed 4” brush spread the coating softly and uniformly and avoid excessive brushing and overworking.
3. Softly blend out any lines of wet coating and let everything settle out.
4. Where bubbles may appear in the StoneSet coating, tap them lightly with the enclosed coarse bristle brush to pop them and make them disappear while the coating is still wet. Any remaining small bubbles will be removed during the next step.
5. Coat the front edge of the counter using the 1” brush.
6. Let the StoneSet coat cure for 24 hours prior to proceeding.

Top Clear is the last step of the LuxROCK™ Kit. It’s a tough polyurethane lacquer formula that adds a visually appealing stain and wear-resistant semi- gloss shield to your new stone surface.
MIXING: Top Clear must be thoroughly and gently stirred. DO NOT SHAKE.

The previously applied StoneSet epoxy coat must be uniformly wet sanded prior to application of Top Clear. This is an important step that is easy to perform. It quickly removes any pimples and other imperfections for a smoothly finished final result. Use the enclosed dust mask while sanding.

1. Use the included misting spray bottle to wet the countertop surface lightly and uniformly prior to sanding and continue misting as you go. This will eliminate dust and lubricate the surface for smoothest polishing.
2. For the easiest and best results, we recommend using a random orbital sander with the enclosed 400-grit sanding disk to perform this step. Use the same disc to wet sand the countertop bull-nose (or straight edges) and small backsplash.
3. If performing all sanding by hand, use the 400-grit disc in a tight circular motion.
4. Sand the surface until it is evenly smooth, and visually free of protruding textural blemishes.
5. When sanding/ polishing is complete, wash the surface with a soaking wet lint-free cloth until there is no dust residue visible on the cloth or your hand.
6. Do a final dry cloth wipe to remove any watermarks or remaining moisture.

APPLICATION

1. Pour some Top Clear into the enclosed paint tray.
2. Use the enclosed one-inch brush for tight areas as well as corners, along edges, etc. Avoid pooling of the clear coat during application.
3. Apply Top Clear over the rest of the countertop with one of the enclosed six-inch rollers. Apply a thin coat, working in manageable sections. Roll in one direction, (not back and forth) with gentle strokes using medium pressure to avoid air bubbles. Softly pass the roller over the wet clear coat once or twice for final softening and uniformity. Keep going in the same manner until the surface is covered. DO NOT OVERWORK OR DISTURB THE TOP CLEAR AS IT ATTEMPTS TO DRY. This could add air bubbles and roughen the finish. Wash the roller after use.
4. Allow Top Clear to dry for about four hours.
5. Apply a second coat in the same manner as the first and allow it to cure for 24 hours.

FINAL BUFFING OPTION: After full cure, use the enclosed 3000 grit polishing pad to buff and burnish the surface. This fast, easy step will remove any final surface flaws in the top clear coat for a lasting, flawless high-end result. And make your new stone countertop even more durable. Enjoy!

CARE TIPS…

• Cutting foods: Though your new surface is durable, use a cutting board for food prep.
• Hot Objects: Your new surface is heat resistant. However, to be safe, use a trivet for added protection.
• Maintenance: Keep your surface in good condition by wiping it clean after use with a damp cloth or common household cleaner.

For LIVE footage of the steps shown here, visit us at www.daichcoatings.com or call 1-866-463-2424. Thank you – and enjoy your new LuxROCK® Surface!

References

• Home - Daich Coatings - Real Stone Coatings

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>