DAICH COATINGS SPR-IG-030 SpreadRock Ice Gray Satin Interior Exterior Instruction Manual
- June 9, 2024
- DAICH COATINGS
Table of Contents
SPREADROCK® INSTALLATION INSTRUCTIONS
SURFACE PREPARATION:
Surface must be structurally sound, clean, dry and free from spalling,
efflorescence, dust, dirt, oils, surface flaking, poorly bonded or glossy
paint, sealers, salts and other contaminates which may effect adhesion and
product performance. New concrete must be allowed a minimum of 30 days cure
time prior to application of SpreadRock ®.
New masonry surfaces should be allowed to cure a minimum of 48 hours prior to
application. Exterior surfaces should be pressure washed using at least 2000
psi to clear any surface contaminates. For application over concrete/masonry
surfaces which have been recently installed, or are smooth or efflorescent the
surface needs to be cleaned and etched with DAICH All-In-One Concrete
Cleaner/Etcher. Etching can also be accomplished with a blended solution of
water and muriatic acid (2 parts water/1 part muriatic acid), follow by gently
rinsing away all etcher and then perform pressure washing for effective
removal of all etching/acid residues. For interior concrete surfaces we
recommend scrubbing with DAICH All-In-One Concrete Cleaner/Etcher or TSP. For
applications over non-porous interior surfaces (vinyl, linoleum, ceramic tile)
we recommended performing surface abrasion prior to washing to create surface
profile for improved adhesion.
MIXING: Thoroughly stir contents prior to application. Use a drill mixing
attachment for effective blending.
PRIMER APPLICATION: Surfaces to be coated with SpreadRock must first be
primed with DAICH Textured Primer. It locks onto the surface and creates an
optimal application area for SpreadRock to grab onto, for lasting adhesion to
concrete and other substrates. Roll a uniform coat (160 – 200 sq.ft. per
gallon) using a 3/8” or 1/2” roller, over the area and allow to dry fully (1 –
2 hrs. outdoors / 2 – 3 hrs. indoors) before proceeding with SpreadRock on
seamless applications or projects using a DAICH Decorative Concrete Stencil.
For projects where tile effects are desired using DAICH 1/4” Grout Line Tape,
added primer dry time may be necessary. See separate instructions for details.
APPLICATION: May be applied by scraper, trowel, squeegee applicator or
texture spray equipment. Ambient temperatures must not be less than 50º F
(10ºC), and should not exceed 80º F (30ºC) during application and for a
continuous period of at least 24 hours after application. Two thin coats are
recommended for highest performance.
- SpreadRock applies easily with a trowel. Pressing firmly, skim out a thin even coat (1/16”) over the prepared, primed concrete.
- Work in manageable sections, preferably between natural breaking points like an expansion joint, grout line or slab edge.
- Apply SpreadRock wet-in-wet as you go for uniform blending and clean results. Use a water bottle to mist wet edges periodically, especially in warmer conditions.
- Apply a second thin coat 4 – 6 hours later, or the next day if more convenient.
Easy Squeegee Application
-
SpreadRock can be applied quickly from a comfortable standing position with a SpreadRock ® Squeegee or similar tool.
Pour down a 1 ft. diameter puddle of SpreadRock and, pressing down firmly, spread it uniformly over the surface in a thin coat (1/16”). -
Work in sections, between natural breaking points like an expansion joint, grout line or slab edge.
-
Apply SpreadRock wet-in-wet as you go. Use a water bottle to mist wet edges periodically for smooth blending, especially in warmer conditions.
-
Apply a second thin coat 4 – 6 hours later, or the next day if more convenient.
Texture Spray Application
- SpreadRock can also be applied using a texture sprayer. Keep the spray nozzle 12 to 18 inches from the surface and spray a uniform layer over the surface. Flatten the sprayed material with a trowel or Squeegee, pressing firmly to pack SpreadRock’s stone granules against the surface. Ideal thickness is approximately 1/16”
- Apply SpreadRock wet-in-wet. Use a water bottle to mist wet edges, especially in warmer conditions.
- Apply a second thin coat 4 – 6 hours later, or the next day. BONUS USE: Spray a very light top “pepper coat” over the dry SpreadRock surface to add ultimate exterior
slip-resistant texture.
CURE TIME:
Dry to touch in 60 minutes, depending on atmospheric conditions. Protect
coated surfaces for 6-8 hours prior to exposure to rain or heavy condensation.
Avoid foot traffic until the following day. In dry conditions product cure is
complete in 24 hours. Equipment can be cleaned with soap and water prior to
cure of material.
SEALING:
Once fully cured for at least 24 hours (longer in damp or cool conditions that
lengthen dry time), SpreadRock finishes must be sealed with DAICH Ultra Clear
Coat Sealer or, for automotive surfaces, DAICH DaiHard Garage & Driveway
Sealer. These sealers are an important final part of the SpreadRock
resurfacing system. They optimize overall water-resistance, cleanliness and
long-term durability. Apply two coats 4 – 6 hours apart. Wear clean shoes to
keep Spreadrock clean before sealing. Re-seal every 2 – 3 years for
residential surfaces and 1 – 2 years for higher traffic commercial areas and
public spaces.
For ultimate cleanliness and protection from oil, grease and chemicals — and
a beautiful showroom finish, seal garage floors, basements, etc. with a thin
uniform coat of DAICH DaiHard 100 Epoxy Clear Coat.
For more information, visit
www.daichcoatings.com**.
MAINTENANCE:
Most stains from food or beverages can be easily cleaned using water or any
effective multi-purpose or citrus cleaner, and a sponge or deck brush. For the
most stubborn stains, we suggest X-Mess Multi-Purpose Cleaner by DAICH
COATINGS for easy safe cleaning of Daich Textured finishes and most other
surfaces.
PRECAUTIONS:
In case of contact with eyes, flood eyes repeatedly with potable water and
call a physician. DO NOT RUB EYES due to granular nature of material. Wash
hands thoroughly after handling. Do not take internally. KEEP OUT OF REACH OF
CHILDREN. Keep container closed. Do not use in the presence of unprotected
foodstuffs. Keep product from freezing. Product which has been frozen must be
discarded. Dispose of unused material in accordance with local, provincial and
federal guidelines.
Proposition 65 – WARNING: This product contains a chemical known to the State
of California to cause cancer.
SPRK 09/28/20