MONOPRICE 10319 3G SDI 2×1 Switch User Manual
- June 5, 2024
- Monoprice
Table of Contents
MONOPRICE 10319 3G SDI 2×1 Switch
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference.
- This device is intended for indoor use only.
- Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately remove it from its power source and allow it to fully dry before reapplying power.
- Do not touch the device, the power cord, or any other connected cables with wet hands.
- Do not expose this device to excessive vibration or extreme force, shock, or fluctuations in temperature or humidity.
- Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it in direct sunlight.
- Do not place or install this device in an area where it can be exposed to excessive amounts of dust, humidity, oil, smoke, or combustible vapors.
- Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred.
- Unplug this device from the power source when not in use.
- Take care to prevent damage to the power cord. Do not allow it to become crimped, pinched, walked on, or become tangled with other cords. Ensure that the power cord does not present a tripping hazard.
- Never unplug the unit by pulling on the power cord. Always grasp the connector head or adapter body.
- Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth with warm water.
- This device has no user-serviceable parts. Do not attempt to open, service, or modify this device.
- This device is intended for indoor use only.
- Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately remove it from its power source and allow it to fully dry before reapplying power.
- Do not touch the device, the power cord, or any other connected cables with wet hands.
- Do not expose this device to excessive vibration or extreme force, shock, or fluctuations in temperature or humidity.
- Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it in direct sunlight.
- Do not place or install this device in an area where it can be exposed to excessive amounts of dust, humidity, oil, smoke, or combustible vapors.
- Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred.
- Unplug this device from the power source when not in use.
- Take care to prevent damage to the power cord. Do not allow it to become crimped, pinched, walked on, or become tangled with other cords. Ensure that the power cord does not present a tripping hazard.
- Never unplug the unit by pulling on the power cord. Always grasp the connector head or adapter body.
- Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth with warm water.
- This device has no user-serviceable parts. Do not attempt to open, service, or modify this device.
INTRODUCTION
Designed for professional SMPTE video applications, this 3G SDI 2×1 Switch allows you to determine which of two connected SDI video sources will be displayed on an SDI monitor. It supports bit rates up to 2.97 Gbps and supports SD-SDI, HD-SDI, and 3G-SDI video signals.
FEATURES
- Distributes one of two connected SDI sources to a single SDI display
- Compatible with the HDcctv 1.0, HD-SDI (ST 292), 3G-SDI (ST 424), and SD-SDI (ST 259) standards
- Supports video resolutions up to 1080p@60Hz
- Supports data raters from 270MHz ~ 2.97Gbps
- Supports 8-bit, 10-bit, and 12-bit Deep Color
- Inputs and outputs are equalized, allowing for longer than normal cable runs
- Supports the RGB, YCbCr 4:4:4, and YCbCr 4:2:2 color spaces
CUSTOMER SERVICE
The Monoprice™ Customer Service department is dedicated to ensuring that your
ordering,
purchasing, and delivery experience is second to none. If you have any problem
with your order, please give us an opportunity to make it right. You can
contact a Monoprice Customer Service representative through the Live Chat link
on our website www.monoprice.com or via email at
support@monoprice.com. Check the website for support
times and links.
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the
items listed
below. If anything is missing or damaged, please contact Monoprice™ Customer
Service for a replacement.
- 1x 3G SDI 2×1 Switch
- 1x AC Power Adapter
- 1x User’s Manual
PRODUCT OVERVIEW
Front Panel
- Select: Press the button to switch between the two inputs.
- 1/2: One of the two LEDs illuminates to indicate the selected input.
- Power: The LED illuminates when power is applied.
- ON/OFF: Use the switch to turn the device on or off.
Rear Panel
- DC/5V: DC barrel connector for connecting the included AC power adapter.
- IN2: BNC connector for connecting an SDI video source device.
- IN1: BNC connector for connecting an SDI video source device.
- OUT: BNC connector for connecting an SDI display.
SAMPLE CONNECTION DIAGRAM
INSTALLATION
Perform the following steps to install this switch into your SDI video system.
- Ensure that all equipment to be connected is powered off and unplugged from its power source.
- Place the Switch in its desired location.
- Ensure that the ON/OFF switch is in the OFF (O) position.’
- Plug one end of a 75-ohm RG-59 cable (available separately) into the video input of an SDI display, then plug the other end into the OUT connector on the Switch.
- Plug one end of a 75-ohm RG-59 cable (available separately) into the IN1 connector on the Switch, then plug the other end into the video output of an SDI video source device.
- Plug one end of a 75-ohm RG-59 cable (available separately) into the IN2 connector on the Switch, then plug the other end into the video output of an SDI video source device.
- Plug the included AC Power Adapter into the DC/5V connector on the Switch, then plug the adapter into a nearby AC power outlet.
- Plug in and power on all connected devices. If necessary, start video playback on each source device.
- Flip the ON/OFF switch to the ON (I) position. The Power LED will illuminate.
- By default, the 1 LED will illuminate, indicating that input 1 is selected. Verify that you can see video from the input 1 device on the connected display.
- Momentarily press the Select button. The 2 LED will illuminate to indicate that input 2 is selected. Verify that you can see video from the input 2 device on the connected display.
Congratulations, the Switch has been successfully installed into your system.
SPECIFICATIONS
| P/N | 10319 |
|---|---|
| Inputs | 2x SDI BNC |
| Output | 1x SDI BNC |
| Supported Standards | HDcctv 1.0, HD-SDI (ST 292), |
3G-SDI (ST 424), SD-SDI (ST 259)
Supported Cable Lengths
| 3G (1080p@60Hz): up to 262 ft. (80m) HD (720p@60Hz): up to 393 ft. (120m) SD
(480i): up to 656 ft. (200m)
Input Power| 5 VDC, 2A
AC Adapter Input Power| 100 ~ 240 VAC, 50/60 Hz
Maximum Power Consumption| 1.5 watts
Operating Temperature| +32 ~ +158°F (0 ~ +70°C)
Storage Temperature| +14 ~ +176°F (-10 ~ +80°C)
Operating Humidity| 10 ~ 85% RH, noncondensing
Storage Humidity| 5 ~ 90% RH, noncondensing
Dimensions (LxWxH)| 3.5″ x 3.3″ x 1.0″ (90 x 85 x 25 mm)
Weight| 7.1 oz (200g)
TECHNICAL SUPPORT
Monoprice™ is pleased to provide free, live, online technical support to
assist you with any questions you may have about installation, setup,
troubleshooting, or product recommendations. If you ever need assistance with
your new product, please come online to talk to one of our friendly and
knowledgeable Tech Support Associates. Technical support is available through
the online chat button on our website
www.monoprice.com or through email by sending a
message to tech@monoprice.com. Check the website for
support times and links.
To download the latest drivers, firmware, manuals, etc., go to
www.monoprice.com and type the P/N into the search
bar. If available, support files are linked at the bottom of the product page.
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Modifying the equipment without Monoprice’s authorization may result in the
equipment no longer complying with FCC requirements for Class B digital
devices. In that event, your right to use the equipment may be limited by FCC
regulations, and you may be required to correct any interference to radio or
television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>