BaByliss E825PE Beard and Hair Trimmer Instructions
- June 5, 2024
- BaByliss
Table of Contents
BaByliss E825PE Beard and Hair Trimmer Instructions
E825PE
Please carefully read the instructions for use below before using the appliance.
PRODUCT FEATURES
- Blades:
- Moveable blade: CMS (Chrome-Molybdenum-Stainless Steel)
- Fixed Blade: stainless steel
- 1 cutting guide for 20 lengths (from 1 mm to 20 mm, in
- mm increments) + length lock system
- Wheel to adjust the cutting length
- Power indicator light
- Plug for use on the mains and for charging
- Cleaning brush, oil
IMPORTANT INFORMATION REGARDING
THE NI-MH BATTERIES OF THIS UNIT
To obtain and maintain the longest battery autonomy possible, allow it to charge for 16 hours before using it for the first time and then approximately every three months. Full autonomy of the unit will only be obtained after three complete recharge cycles.
CHARGING THE TRIMMER
- Plug the cord into the unit and connect the transformer. Before using the trimmer for the first time, allow it to charge for 16 hours. Make sure the trimmer’s switch is in the OFF position.
- Check that the charging indicator light is lit.
- A full charge provides a minimum of 30 minutes’ use of the trimmer.
- Subsequent charges should also be 16 hours.
USE ON THE MAINS
To use the trimmer on the mains, plug the cord directly into the unit. Plug
the trimmer, in the OFF position, into the mains and switch ON (if the battery
is very weak, wait about 1 minute).
IMPORTANT! Use only the adapter that is supplied with the trimmer.
HANDLING THE COMB GUIDE
NOTE: Always put the comb guide on BEFORE turning the trimmer on, and
turn the trimmer off before removing it. To remove or replace the comb guide,
first set the comb guide to the triangle mark beyond position 20 (Fig. 1)
and, with the motor off, pull the guide up to remove it (Fig. 2),
press the guide down then turn the dial to put it on **(Fig. 3).
**
TURNING IT ON AND USING IT
To adjust the cutting length of the trimmer, turn the dial.
The length-lock system allows you to lock the cutting length setting (Fig.
4). Once the cutting length is selected, slide the switch to the «lock»
position. To change the cutting length, make sure you unlock the switch before
using the dial. Switch the ON/OFF button.
You can change the cutting length at any time.
NOTE! Make sure you hold the comb head flat against the skin. That is,
the tips of the teeth and the little corners protruding from the comb should
always be in contact with the skin. If not, the precision of the cut may
change **(Fig. 5-6).
**
MAINTENANCE
Regular maintenance of the trimmer blades will keep them in optimal working condition.
Removable blades
To make cleaning easier, the BaByliss trimmer blades can be removed. Make sure the trimmer is turned off and then remove the comb guide. Hold the trimmer with the blades facing up and remove them by pressing on the tips of the blades (Fig. 7).
Carefully brush the blades using the cleaning brush to remove hair
Self-lubricating blades
The blades of your trimmer have a reservoir pad for releasing the necessary amount of oil for proper operation of your trimmer, time after time. Nevertheless, it is recommended that it be refilled occasionally when you notice performance is not as high.
Remove the blades as described above.
Squeeze a few drops of BaByliss oil onto the pad (Fig. 8). Then replace
the blades on the trimmer.
The BaByliss oil is specially formulated for the trimmer, it does not
evaporate nor does it slow the blades. It is possible to obtain replacement
blades when these are worn out or damaged.
BABYLISS SARL
99 avenue Aristide Briand
92120 Mont rouge
http://www.babyliss.com/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>