BaByliss PRO BAB895U Cordless Clipper Instruction Manual

Model: BAB895U
SNAP FX CORDLESS CLIPPER

SNAP FX CORDLESS CLIPPER

Heavy-duty professional cordless clipper with high-torque brushless motor and DLC blades for smooth powerful cutting. The SNAP FX dual lithium battery system charges two high capacity batteries at once for continuous cutting performance.

FEATURES

• Precision engineered DLC blades with a super sharp V cutting angle
• Advanced high capacity lithium batteries for up to 90 minutes cordless use from a fast 3 hour charge
• High-torque brushless motor for supreme power and speed for clean, close cutting
• Robust all metal housing
• 8 comb guides – grades 0.5, 1, 1.5, 2, 3, 4, 5, 6
• Magnetic hair pocket cover for easy cleaning
• Cordless
• Dual charging and storage stand
• Includes oil and cleaning brush

SAFETY CAUTIONS

• Original instructions. Read these safety precautions carefully before using the unit! This appliance should only be used as described within this instruction booklet. Please retain for future reference.

IMPORTANT CHILD SAFETY

• ALWAYS keep out of the reach of very young children (during and after use).
• This appliance should not be used, cleaned or maintained by children.
• Always take extra care if used on children or near children.
• Do not use on very young children.

IMPORTANT SAFETY

• WARNING! Do not use this appliance near bathtubs, showers, basins or other vessels containing water.

• Do not immerse the appliance in water or other liquids.

• Keep the appliance dry.

• UK Only: Do not use this appliance in the bathroom.

• Outside the UK: If using the appliance in a bathroom, unplug after use as the proximity of water can be dangerous even if the appliance is switched off. For additional protection the installation of a residual current device (RCD) with a rated residual operating current not exceeding 30mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.

• The appliance’s charging stand and/or adaptor must be kept away from sources of water so that they do not fall into the water.

• CAUTION! Keep the power cord and the appliance dry. For appliances with a removable power supply unit, remove the power cord before cleaning.

• Always inspect the appliance before use for noticeable signs of damage. Do not use if damaged or if the appliance has been dropped. In the event of damage contact the Conair Customer Care Line (refer to ‘UK After Sales Service’ section for further information).

• Do not use the appliance if the charging adaptor or lead is damaged. In the event of damage, discontinue use immediately. If the charging adaptor or lead is damaged, it must be replaced by the manufacturer. Return the appliance to the Customer Care Centre (refer to ‘UK After Sales Service’ section for further information). No repair must be attempted by the consumer.

• Only use the attachments supplied with this appliance.

• WARNING! For the purposes of recharging the battery, only use the detachable charging supply unit provided with this appliance.

• Do not leave the appliance unattended when switched on.

• Do not leave the appliance plugged in for more than 24 hours.

• Unplug immediately if any problems occur during use.

• Do not place the appliance on any surface whilst in operation.

• Special care is required when using the appliance close to the ears, eyes and face.

• This appliance may be used by children aged from 8 and older and people with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction on the safe use of the appliance and understand the hazards involved. Children must not play with the appliance.

• This product contains a lithium ion battery that is not to be removed from the appliance for charging. The batteries in this appliance are non-replaceable. Batteries must be disposed of safely at the end of life.
  Please take to a recycling centre for safe disposal. If the battery leaks, avoid touching it and dispose of it at a recycling centre.

• The supply terminals are not to be short circuited.

• This product complies fully with all appropriate EU and UK Legislation and the standards relevant to this type and class of appliance. We are an ISO9001:2015 certified company that continually evaluates our Quality Management System performance. If you have any queries regarding product safety and compliance, please contact the Conair Customer Care Line (refer to ‘UK After Sales Service’ section).

WEEE – END – OF – LIFE ELECTRICAL AND ELECTRONIC EQUIPMENT
In everybody’s interest and to actively participate in protecting the environment and human health:

• Do not discard your products with your unsorted household wastes.
• The WEEE (Waste electrical and electronic equipment) must be collected separately.
• Use the return and collection systems dedicated to the WEEE available in your area. In this way, some materials can be recycled, re-used or recovered.
• By ensuring this product is disposed of properly, you will help prevent potential negative consequences for the environment and human health due to possible content of hazardous substances.

For more detailed information about the disposal of this product, please contact your local household waste disposal service.

TECHNICAL DATA

Vibration and noise levels

INSTRUCTIONS FOR USE

IMPORTANT! Only use the adapter and attachments supplied with this appliance.

General

• Always inspect the appliance before use to ensure the clipper blades are free from hair, debris etc.
• Use on clean, dry hair that has been combed until tangle-free.

Charging the Appliance

• Before using the appliance for the first time, charge the battery continuously for 3 hours. Maximum battery capacity will only be reached after 3 completed charging and discharging cycles.

• Plug the charging adapter into a suitable mains power socket and connect to the unit and switch on.

• Place a battery in each of the pockets of the charging stand and the clipper into the central pocket.

• The blue LED indicator light will flash when correctly connected to the mains power and will continuously flash until the battery has fully charged.
  NOTE: Always place the clipper in the base with the ‘I/0’ switch in the OFF position.

• Charging is complete after 3 hours — the light will go from flashing blue to a solid blue to indicate charging is complete.
  NOTE: The charging stand may become warm while charging. This is normal.

• If the charging light starts to flash rapidly (more than 4 flashes per second) then the appliance is faulty. If this happens then please stop charging and remove the adapter from the mains and contact the Conair Customer Care Line. (See ‘UK After Sales Service’ section for further information).

BATTERY INDICATORS

Critically Low Battery – Red Flashing Light
Low Battery – Blue Flashing Light
Unit On and Battery Fully Charged – Blue Light
Error – Red Flashing Light (more than 4 flashes/second)

AUTOMATIC CHARGING MANAGEMENT

One Battery – 2.4A Fast Charging
Two Batteries – 1.2A Normal Charging

BATTERY REMOVAL AND INSTALLATION

• The clipper features removable and rechargeable batteries, so you can cut and style for extended amounts of time with minimal interruption.
  NOTE: Make sure the clipper switch is in the OFF position before removing or installing battery.

• To remove the battery, press on the two tabs toward the bottom of the unit and pull the battery out of the bottom of the unit. Then place into charging stand.

• To install a new battery, line up the tabs of the charged battery with the slots on the sides of the unit and slide up into the housing, pressing firmly until battery clicks into place.

HOW TO USE COMB ATTACHMENTS

To use the comb attachments, turn the clipper to “ O ” position.
Slide the comb attachment onto the top of the clipper blades and then pull down and over the back of the blade. To remove, pull up on the back of the comb attachment and then pull away from the blade.

ADJUSTABLE TAPER LEVER

The taper lever is positioned at your thumb. You can hold the clipper in your hand and adjust the lever at the same time – while you are clipping.
The taper lever adjusts the closeness of the cut from a close cut with the taper lever in the up position to a longer length cut with the taper lever in the down position. To increase cutting length, slowly push the lever down. To cut closer, push the lever up. As different cutting edges are used in each setting, using the taper lever lengthens the life of the clipper blades.
Too much hair can slow down the hair clipper. Keep the clipper on to remove hair. Then push the taper lever back and forth quickly several times. If you do this every time, especially after frequent hair cutting, the clipper blades should remain free of cut hair. Oil the blades after the above procedures.

HAIR POCKET DOOR

The top housing of the clipper has a removable, magnetic door integrated into the top housing, allowing for easy access to and cleaning of critical moving parts.
To remove the magnetic door, place fingers on the side tabs and pull straight away from the unit.
To clean internal moving parts, use compressed air or the included small cleaning brush to clear out hair from the housing after the magnetic door has been removed.
Once finished with cleaning the moving parts of the clipper unit, carefully place the magnetic door back in its proper position. The magnets should pull the door back into place.

CLEANING AND MAINTENANCE

To maintain correct performance, the blades must be regularly cleaned and oiled.

• Brush away the hair from the blades using the cleaning brush provided.
• It is recommended to oil the blades every time that the clipper is used, using the oil provided. Never use any other product: this oil was formulated for high speed clippers, it does not evaporate or slow down the blades.

UK GUARANTEE

This BaByliss PRO appliance is guaranteed for professional use for 2 years and is only valid within the United Kingdom.

Exclusions
This guarantee will no longer be valid meaning that The Conair Group Ltd will not be liable to repair or replace your product where:

1. The appliance has been used on a voltage supply other than that which is marked on the product, or advised within this instruction booklet.
2. The appliance has been purchased from an unauthorised stockist*.
3. Repairs or alterations have been attempted by unauthorised persons.
4. The failure of the appliance is a direct result of misuse.
5. The failure is a result of not following the instructions for use.

This guarantee does not cover any cosmetic damage due to misuse of the product nor any damage to persons or property that occurs because of product misuse.

• unauthorised stockists include, but are not limited to online auction sites, private sellers and those selling second hand goods, refurbished products etc.
  Please contact the Conair Customer Care Line on 03705 133 191 (09:00 to 17:00 Monday to Friday) or e-mail ukinfo@conair.com for further information on authorised stockists.

It is important to retain your proof of purchase. We recommend attaching your receipt to this page.
Even where a refund may be applicable, no refund will be provided without a valid receipt or proof of purchase, we will only be able to offer a repair or replacement service. Please note this does not apply if the product was purchased directly from The Conair Group Ltd.
Guarantees on replacement products run from the original purchase date or date of delivery, whichever is later, and not from the date of replacement.

This guarantee is an additional benefit and does not affect your statutory rights as a consumer.
If you have any queries regarding this guarantee please contact the Conair Customer Care Line on 03705 133 191 (09:00 to 17:00 Monday to Friday) or e-mail ukinfo@conair.com.

UK AFTER SALES SERVICE
For further advice on using the appliance or should you need to return your product, please contact the Conair Customer Care Line on 03705 133 191 (09:00 to 17:00 Monday to Friday) or e-mail your enquiry to ukinfo@conair.com.

Return address:
Customer Care Centre
Conair Logistics
Unit 4, Revolution Park
Buckshaw Avenue
Buckshaw Village
Chorley
PR7 7DW

Please enclose your returns number, name and address details, together with a copy of proof of purchase and details of the fault.

Please note this Instruction Booklet is not the guarantee.

**** SAFE DISPOSAL

This appliance contains Li ion batteries. To protect the environment this appliance and its batteries must be disposed of safely. At the end of its life, please take this appliance to a recycling centre, where the internal rechargeable battery should be removed by a professional and recycled separately. For more information about the recycling of electrical and battery operated appliances please contact your local council office or your household waste disposal service. For specific enquiries regarding the replacement of batteries in this product please contact our Conair Customer Care Line (refer to ‘UK After Sales Service’ section).

UKCA DECLARATION OF CONFORMITY
In accordance with UK Government guidance

We, the undersigned, take full responsibility for the product’s compliance.

Type of product: Clipper
Type number: T180a
Trademark: BaBylissPRO / Conair / CPL
With following characteristics: PRI: 100-240V~, 50-60Hz, 0.4A Max
SEC: 4.5VDC, 2.5A, 11.25W
Country of origin: China
Manufacturer name: Conair UK
Address: PR7 7DW

The object of the declaration described above is in conformity with the relevant UK Statutory Instruments (and their amendments):

Electrical and Electronic Equipment Regulations 2012
2019 No. 539| Ecodesign for energy-related products and energy information (Amendment) (EU Exit) Regulations 2019
2008 No. 1597| Supply of Machinery (Safety) Regulations 2008

References to the relevant designated standards used or references to the other technical specifications in relation to which conformity is declared:

LVD| BS EN 60335-1
BS EN 60335-2-8| 2012
2015| A2: 2019; A15: 2021
A1: 2016
---|---|---|---
(including EMF)| BS EN 62233| 2008|
Ecodesign| BS EN 50563| 2011| A1: 2013
EMC| BS EN IEC 55014-1
BS EN IEC 55014-2
BS EN IEC 61000-3-2
BS EN 61000-3-3| 2021
2021
2019
2013| A1: 2021
A1: 2019 ; A2: 2021

The technical documentation is available from:
Name: The Conair Group Ltd,
Address: Unit 4, Revolution Park, Buckshaw Avenue, Buckshaw Village, Chorley, PR7 7DW

Signed by and on behalf of:
BABYLISS FACO S.R.L. (authorised by BABYLISS S.A.R.L. and The Conair Group Ltd)
Avenue de l’Indépendance 25, B-4020 Wandre, Belgium

EU DECLARATION OF CONFORMITY
This declaration of conformity is issued under the sole responsibility of the manufacturer

Type of product: Clipper
Type number: T180a
Trademark: BaByliss PRO / Conair / CPL
With following characteristics: PRI: 100-240V~, 50-60Hz, 0.4A Max
SEC: 4.5VDC, 2.5A, 11.25W
Country of origin: China

The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:

(EC) No. 1275/2008 amended by (EU) No. 801/2013 and (EC) No. 2019/1782 (where applicable)
2006/42/EC| Machinery Directive

In accordance with the following standards

LVD| EN 60335-1
EN 60335-2-8| 2012
2015| A11: 2014; AC: 2014; A13: 2017; A1: 2019;
A2: 2019; A14: 2019; A15: 2021
A1: 2016
---|---|---|---
(including EMF)| EN 62233| 2008|
Ecodesign| EN 50563| 2011| A1: 2013
EMC| EN IEC 55014-1
EN IEC 55014-2
EN IEC 61000-3-2
EN 61000-3-3| 2021
2021
2019
2013| A1: 2021
A1: 2019; A2: 2021

CE mark first affixed CE: 12/2022

Signed by and on behalf of
BABYLISS FACO S.R.L. (authorised by / The Conair Group Ltd)

BaByliss FACO s.r.l. – 25, Avenue de l’Indépendant
– B-4020 WANDRE – BELGIUM – ****: (0032) 04 345 60 60
– FAX: (0032) 04 345 60 88
Reg. Com. Lg. 116.914
– Β.C.E. 0412.537.139
– VAT BE 0412.537.139
– Société Générale: BE84 6881 00439259
– Swift: SGABBEB2
IB-23/211A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>