PERFECT WATER TMULTRA Home Master Series Reverse Osmosis System Instructions
- June 5, 2024
- PERFECT WATER
Table of Contents
Perfect Water Technologies Series
Reverse Osmosis System
Home Master®
Filter Change Instructions
Insert tube Push up to tube stop
Push the tube into the fitting, to the tube stop. The collet (gripper) has
stainless steel teeth that hold the tube firmly in position while the ‘0’ ring
provides a permanent leakproof seal.
Pull to check secure
Pull-on the tube to check that it is secure. It is a good practice to test
the system prior to leaving the site and/or before use.
Push in the collet and remove the tube
To disconnect, ensure the system is depressurized before removing the tube.
Push in collet squarely against the face of fitting. With the collet held in
this position, the tube can be removed.
Home Master® Series Reverse Osmosis System Filter Change Instructions
Tools Required Tube cutter or Scissors
Towel and/or Paper Towels
-
Clear away a workspace under the sink near the location of the Home Master RO System.
-
Close the water valve feeding the Home Master RO, by either closing the Home Master ball valve located on the cold water line or alternatively, by closing your angle-stop feed water valve clockwise. If present, close the inline ball valve feeding refrigerator/icemaker. For models UV, ULTRA or HydroPerfection—disconnect the power adapter.
-
Close the reserve tank valve located on top of the reserve tank. When closed the blue handle will be perpendicular to the waterline.
-
Depressurize the system. Flip-up the handle on the RO faucet so that it locks into place, and dispenses water until it no longer flows. The water flow should fall off and stop in seconds. If water still continues to flow, repeat steps 2 & 3. The system is now depressurized; continue to leave to RO faucet in the open position.
-
Slowly and gently pull the Home Master RO off of its mounting clips from the bottom up. Lay it on a towel. Pull off the first filter to be changed—typically the sediment filter at the system inlet. IMPORTANT: Make a note of flow direction arrows on the filters or take a picture to maintain a consistent flow. Please service one filter at a time.
-
To remove the tubing from the filter – push down the collet ring to the filter body with the thumb and forefinger while simultaneously pulling on the tubing as shown on the cover figure. Some mild resistance to pulling out the tubing is normal. Removing the tubing will be impossible without first fully depressurizing the Home Master RO as described in step 4. Immediately trim off a ¼” from the end of the tubing with the scissors. Make sure the tubing end is smooth and round before inserting it into the replacement filter. NOTE: A rough or oblong tube end will leak.
-
Insert the tube end about a ¼” into the replacement filter fitting then pull back gently to ensure a snug fit. Repeat step 6 for the other end of the filter. Immediately discard the used filter. Repeat step 6 for each of the next replacement filters. For UV bulbs -See Below
-
Remount the Home Master RO. For models UV, ULTRA and HydroPerfection reconnect the power adapter. Dry any excess water at the fittings with a paper towel.
-
SLOWLY open the main water line to the Home Master RO. In 2 –20 minutes water should flow from the RO faucet in a trickle. Initial Page 3 3 discharge may be accompanied by a harmless discoloration due to loose carbon.
-
After the trickle runs clear, close the lever on the RO faucet and allow the system to pressurize. When the system has pressurized fully it will shut off automatically, usually in a few minutes. (IMPORTANT STEP) dry unit thoroughly again, gently tug on each connection and check for leaks. Then open the reserve tank valve slowly. Allow reserve tank to fill until full, which may take up to 3 hours.
-
When the tank has filled completely, and the system shuts off automatically, then close the feed valve and open the RO faucet to allow the water to drain out until it comes to a complete stop. Then reopen the feed valve and allow the system to refill again. A further tank flush may be necessary depending on the initial tank fill level. Finally, if present, open the inline ball valve feeding the refrigerator/icemaker
VIDEO INSTRUCTIONS:
https://flowcode.com/p/e0ZP85zVM
– scan 2d QR code with smartphone camera –
System schematics are available upon request.
www.ThePerfectWater.com or contact customer
service at 877-693-7873. We will be
happy to assist you with your filter change.
Perfect Water Technologies, Inc.
Copyright © 2021
Version 9
Customer Service Hotline 1-877-693-PURE