EACHINE Wizard Ts130 Fpv Racing Drone Pnp Omnibus User Guide
- June 5, 2024
- Eachine
Table of Contents
Wizard Ts130 Fpv Racing Drone PNP Omnibus
User Guide
Package included
1 x Eachine Wizard TS130 frame kit| 2 x T3056C 3-blade propeller transparent
white CCW
---|---
1 x TS 20A 4in1 Brushless ESC| 2 x T3056C 3-blade propeller blue CW
4 x TS1507 4100KV brushless motor| 2 x T3056C 3-blade propeller blue CCW
1 x F4 flight controller| 1 x Antenna
1 x FOXEER Arrow MICRO PRO camera| 1 x Battery strap
1 x 5.8G 40CH 25mw 100mw 200mw switchable VTX| 2 x Carbon fiber wrench
2 x T3056C 3-blade propeller transparent white CW| 10 x Nylon cable tief
Frame kit
Wheelbase: 130mm
Material: 3K carbon fiber
Top plate thickness: 2mm
Bottom plate thickness: 3mm
Artist: hydrographics transfer printing
Motor
| Idle Current (Io/10V): 1.68A | Stator Thickness: 7mm |
|---|---|
| Lipo Cell: 3-4S | Motor Diameter: 21.6mm |
| Weight: 17.6g | Motor Body Length: 15.5mm |
| Max Continuous Current: 26A | Overall Shaft Length: 29mm |
| Max Continuous Power: 416W | Prop adapter shaft: M5 |
| Max thrust: 626g(4S/3″) | Bolt holes spacing: 12mm |
| Configu-ration: 9N/12P | Bolt thread: M2 |
| Motor Resistance (RM): 0.0495 Ω | Propeller: 3” |
| Stator Diameter: 15mm |
ESC
Continuous current: 20A
Peak current (5S): 25A
Input voltage: 2-4S
Supports Dshot600, Dshot300, Dshot150
Size: 27x27mm
Weigjt: 3.3g
Flight controller
CPU: f4STM32 F405 SCM
Input voltage: 3-4S
Sensor: MPU6000 SPI
Built in OSD
Built in 5V 2A BEC
Size: 25x25mm
Weight: 2.3g
Switchable VTX
Input voltage: 7-24V
Dimensions: 20x20mm
Size: 27mm×27mm×4.5mm
Adjustable 25mw / 100mw / 200mw
Supports smart audio (remote OSD parameter adjustment)
There are two ways to control the frequency and power of the launches: <1>
Enter the release: FEATURES->VTX SA can enter the following interface.
uses a remote control to visualize control, as shown in Figure 1.1
Figure 1.1
The second row is the status bar, respectively.
F: freestyle modeF5: is now in frequency band F, fifth frequency point.
5820: now has a frequency of 5820.
500: now has a transmit power of 500MW Third lines
BAND: indicates frequency band, and BAND can be modified by remote control.A
(BOSCAM A) B (BOSCAM B) E (BOSCAM E) F (FATSHARK) F (E) Fourth lines
CHAN: represents frequency points, and the 1—8 can be modified by remote
control. Fifth lines
(FREQ): indicate the corresponding frequency now, changing with the band and
Chan above.
Sixth lines
POWER: indicates the transmission power and can be adjusted.
Switchable VTX
Seventh lines
SET: Enter and select YES to confirm your BADN, CHAN, and POWER settings and
take effect immediately., as shown in Figure 1.2 below
Figure 1.2
Eighth lines
The CONFIG: function is set in, as shown in Figure 1.3 below.
OP MODEL: mode adjustment, with free mode and race mode, needs a reboot
to take effect.
FSEL MODE: regulates frequency setting mode, CHAN, and user, user mode is
temporarily invalid.
PIT FMODE: PITMODE mode, with PIR and POR mode.
Switchable VTX
In the POR mode, POR FREQ: can enter into any frequency between 5300-5900, as
shown in Figure 1.4.
STATX: status information
XMM-VTX is operated by a button with three LED lights (red <2> light CH1-8;
blue light BAND1-5; green light power 1-3 <25100-200 mW>)and TBS Smart Audio
remote control operation.
Keyboard operation: Long press 3S (three LED indicators are all on) to open
and enter CH switching operation, and the red light will flash, flashing once
represents the currentCH1 (2-8 times for CH2-CH8 respectively). At this time,
a short press of the key CH plus 1 will flash the corresponding number of
times.
CH1-8 cycle. Press the button 3S (three LED lights are all on) to open and
enter the BANDswitching operation, and the blue light will flash. The flash
once represents the current BAND1 (2-5 times for BAND2-BAND5 respectively). At
this time, press the button BAND plus 1, and the blue light will flash
correspondingly. BAND1-5 cycle. Press the button 3S (three LED lights are all
on) again to open the power switching operation, and the green light will
flash, one time representing the current power of the first grade (2-3 times
for the green light flashing respectively), at this time, press the button
power to add one gear, and the green light will flash the corresponding number
of times. Power stall 1-3 cycle.
Press the button 3S again (3 LED lights are all bright) to release the above
settings again. Note that the previous settings will not be saved if the power
is off before saving. For example, if CH is only set, it is also necessary to
press 3S three times longer to save the settings. Long press button 8S (green
light) to quit PIT mode.
Switchable VTX
Band| CH1| CH2| CH3| CH4| CH5| CH6|
CH7| CH8
---|---|---|---|---|---|---|---|---
Band-A| 5865| 5845| 5825| 5805| 5785| 5765| 5745| 5725
Band-b| 5733| 5752| 5771| 5790| 5809| 5828| 5847| 5866
Band-E| 5705| 5685| 5665| 5665| 5885| 5905| 5905| 5905
Band-F| 5740| 5760| 5780| 5800| 5820| 5840| 5860| 5880
Band-r| 5658| 5695| 5732| 5769| 5806| 5843| 5880| 5917
Note: In the remote control, the power of 25 corresponds to the actual 25 mW, 200 corresponds to the actual 100 mW, and 500/800 corresponds to the actual 200 mW.
Camera
Solution: 1/3” Sony SUPER HAD II CCD+Nextchip 2040 DSP
Pixel: PAL: 976(H) x 494(V);NTSC: 768(H)×494(V)
TV System: PAL/NTSC (based on country)
Resolution: 600TVL(color) 650TVL(B&W)
Synchronization: internal
Min. Illumination: 0.01Lux
WDR: support
OSD programming board: support
White Dot Repair: support
DNR: 2D DNR
Camera Title: support
Image Adjustment: support
OSD: Edit Name, Power, Flying time
Input Power: 5-40V
Storage Temperature: -40 C ~ 60 C
Working Temperature: -10 C ~ 50 C
Power Consumption: 70mA
Low voltage alarm: Support
Preset mode: DEF, VIVID, SUNNY, CLOUDY, LED TR, USR1
Size: 18.5*19mm (bracket excluded)
Weight: 5.3g (bracket excluded)
Motor Unlock/lock
Motor Unlock
Put the throttle rocker at the lowest point, move the rudder rocker to the
right and keep it for more than 2 seconds. The blue state indicator is always
on, that is unlock the motor.
Motor lock
Put the throttle rocker at the lowest point, move the rudder rocker to the
leftmost side, and the red state indicator is always turned on to lock the
motor. At this time, pushing the throttle rocker motor upward will not rotate.
Traversing flight
- Flying is more suitable for experienced pilots.
- During the flight, please keep the flight within the video receiving range (the actual range depends on the flight environment and weather conditions).
- During flight, please avoid crowds, animals and High voltage wires and other obstacles
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>