PHILCO PEB 608 IX Range Hood User Manual
- June 5, 2024
- PHILCO
Table of Contents
RANGE HOOD
USER’S MANUAL
PEB 608 IX
PEB 644 W, PEB 644 IX
Dear customer,
Thank you for buying a PHILCO brand product. So that your appliance serves you
well, please read all the instructions in this user’s manual.
PART 1: IMPORTANT SAFETY INSTRUCTIONS
Recommendation:
Carefully read these instructions before installing and operating this range
hood. Write down the serial number found on the rating label of the range hood
in the space below. It s essential that you store this user’s manual in a safe
place so that you can use it in the future. If you intend to sell the
appliance, give it to another owner, or if you move, always make sure that the
user’s manual is attached to the appliance so that the new owner can also
learn about the operation of the appliance and the relevant warnings.
SERIAL NUMBER:
Important safety instructions
- This appliance is designed for household use only.
- Before connecting the power cord plug, make sure the voltage stated on the rating label of the appliance corresponds to the voltage in your wall socket. Connect the power ord plug to a power socket with a voltage of 220 – 240 V ~ 50 Hz.
- Only use a properly grounded power socket. The appliance may only be connected to a properly grounded power socket.
- All electrical connections must be performed by a qualified electrician.
- Installation performed by an unqualified person may cause incorrect operation, damage to the appliance, create a fire hazard, or cause injury to persons.
- Neither the manufacturer nor the vendor takes responsibility for damages caused by incorrect or unprofessional installation, connection, or operation. Tampering with the appliance by an unqualified person will void the customer’s right to a warranty repair.
- Do not expose the power cord to excessive pressure or loads, and do not place heavy objects on it, it must not be tangled and it must not be stepped on. Do not locate the power cord in or on heat sources such as stoves, heating, or other generators of heat. Otherwise, this may damage the power cord or create a fire hazard.
- Only connect the power cord plug to a power socket after the entire installation is completed.
- The power plug serves as a disconnection device and for this reason, the power socket must remain easily accessible in the event of a dangerous situation unless it is connected to a terminal box.
- Do not touch the lights if the appliance has been running for some time. Lights heat up during operation and may cause burns.
- This appliance is designed for fume extraction during standard domestic use. Do not use the appliance for purposes other than those for which it was designed. Otherwise, you expose yourself to the risk of a dangerous situation and void the warranty.
- Follow the instructions for installation and ventilation (with the exception of when a fi re stove is used).
- Do not use the fl ambé cooking method under the range hood.
- Regularly replace the filters in the range hood. Otherwise, this presents a fi re hazard.
- Only use filters suitable for use with the range hood. The manufacturer or distributor will recommend a suitable filter type.
- Do not use the appliance without the aluminum filter inserted. Do not take out the filters while the appliance is on.
- Regularly clean the appliance to prevent a dangerous situation from occurring.
- Before cleaning, replacing filters, moving, or any other maintenance, turn off the appliance and pull out the power plug from the power socket, or turn off the respective circuit breaker.
- If you are using another gas or natural gas appliance in the room at the same time, the fumes from this appliance must be spatially isolated.
- If a chimney is connected to the exhaust of the range hood, use pipes with a diameter of 150 or 120 mm. The pipe connection should be as short as possible.
- Keep packaging materials out of children’s reach. They could suffer injury or suffocation.
- Children must be supervised to ensure that they do not play with the appliance. If the power cord is damaged stop using the appliance. Has the power cord been replaced at n authorized service center or by another qualified person? Under no circumstances should you replace the power cord yourself.
To ensure safety, use a fuse with a maximum rating of 6 A.
WARNING!
This appliance must not be used by persons (including children) with physical
or mental impairments or by inexperienced persons unless properly trained or
schooled in the are some of the appliances, or unless they have been properly
supervised by a qualified person who will be responsible for their safety.
Attention when transporting or carrying
The packaging materials are from recyclable materials, so dispose of them in
an environmentally conscientious
manner according to regulations in force.
During transport adhere to the symbols of the cardboard box.
When carrying the appliance, hold it by the respective handles.
NOTE:
We recommend that you keep the original packaging at least for the duration of
the warranty period in the event of repair or refund and transport to the
authorized service enter. Adhere to the symbols on the cardboard box.
If you do not have the original cardboard box, adhere to the following
instructions:
a) Do not place any items on the appliance that could damage the appliance
during transport.
b) Protect the appliance against impacts, falls, etc.
c) Wrap the appliance, e.g. in bubble wrap which will protect the appliance
from damage.
NOTE:
The carbon filter is not included.
NOTE:
If the building is equipped with a heat recovery system, it is necessary to
set up the appliance for internal air circulation (without an exhaust). In
that case, it is necessary to purchase the carbon filter.
PART 2: DESCRIPTION OF THE APPLIANCE
- Front panel
- Control panel
- Filter
- Lighting
PEB 608 IX
PEB 644 W, PEB 644 IX
Remote control (optional accessory)
a) Turn the appliance on / off
b) Increase the exhaust power
c) Decrease the exhaust power
d) Turn the lights on / off
PART 3: INSTALLATION
Unpacking
- After unpacking remove all packaging and advertising labels from the appliance.
- Check that the appliance has not been damaged and that the package includes all this user’s manual.
- If the appliance was damaged during transport, contact the authorized service center
- Do not use a damaged appliance under any circumstances.
Important
Ensure that children do not play with the packaging material.
Dimensions of the appliance
PEB 608 IX
PEB 644 W, PEB 644 IX
Supplied accessories (depending on the model)
A non-return exhaust flap must be installed into the air outlet of the range
hood (unless one is already factory installed). This part is not included, it
must be purchased separately.
Placement
Install the range hood at a height of at least 65 cm above an electric cooktop
or at a height of 75 cm above a gas cooktop.
IMPORTANT:
Before installing or using the appliance, please first read all instructions
and check that the voltage and frequency values on the rating label correspond
to the voltage and frequency in your electricity grid. We recommend that the
appliance be connected by a service technician or another qualified person in
compliance with local codes and regulations.
Before starting the installation
- Check that the purchased appliance has the correct dimensions corresponding to the chosen installation location. Furthermore, ensure that there is an electrical power socket available that will remain accessible even after the range hood is installed.
- Before installing the range hood, check that all necessary masonry work is complete.
- Have all electrical connections performed by a qualified person.
- We recommend that you remove the aluminum filters before installing the range hood.
- Check that there are no packaging materials or other materials, e.g. user’s manual, warranty card, or bags with screws, inside the appliance. These need to be taken out and kept for possible use in the future.
- We recommend that you disconnect and move to the side free-standing or built-in stoves so that you have easier access to the rear wall or ceiling. If this is not possible lace protective material onto the work area, cooktop, or stove. This will prevent damaging these surfaces.
- Select an even surface for the necessary assembly of the range hood. Cover the surface with protective material and place all parts of the range hood and fastening elements onto it.
- It is necessary that a qualified technician inspects the suitability of the supplied fastening material and other components for the specific wall/ceiling type. The wall/ceiling must be sufficiently strong to hold the weight of the range hood.
- Do not attach this range hood to a wall or cabinet furniture by tiling, or plastering, and do not glue it on using silicone glue. The appliance is designed to only be installed n a wall/ceiling.
- We recommend that always two people perform the installation of the appliance.
If your range hood is designed to be mounted to the ceiling, adhere to the following instructions.
- The range hood must only be suspended on ceiling beams or on load-bearing ceiling beam connections.
- Do not suspend the range hood on false ceilings.
- The ceiling must have a load-bearing capacity of at least 40 kg.
- The ceiling thickness must be at least 30 mm.
IMPORTANT:
THE RANGE HOOD MAY ONLY BE CONNECTED TO THE ELECTRICAL GRID AFTER THE ENTIRE INSTALLATION IS COMPLETE.
Drill 4 holes into the bottom wooden shelf according to the pattern on the top plate of the range hood. Also, cut out a hole for the exhaust with a diameter of 130 mm.
Use the provided screws (3.5 x 45) to mount the range hood into the cabinet. Check that the extensible part is not preventing the cabinet doors from opening/closing.
Exhaust connection
NOTE:
This range hood may be used with or without an exhaust. Nonetheless, it is
recommended to install it with the exhaust option. The carbon filter is not
included.
WARNING!
The air outlet must not be connected to the chimney of a fi re stove or
another similar outlet used for heating.
-
Place the exhaust flange onto the range hood. This part is not included, it must be purchased separately.
-
Attach one end of the aluminum fl ue pipe to the range hood flange and the other end to the air outlet. Check that both ends are firmly attached and secured in place.
-
Bends and deviations in the aluminum fl ue pipe reduce the exhaust performance, so it is essential that the pipe is bent as little as possible.
Right …………………………………Wrong
Carbon filter
If you are using the range hood without an air exhaust, it is necessary to use
a carbon filter. The carbon filter is not included. Contact your vendor or an
authorized service center to purchase this filter.
- Before installing or replacing the carbon filter, check that the appliance is turned off and disconnected from the power socket or that the respective circuit breaker is turned off.
- It is necessary to replace the carbon filter regularly every 3 – 5 months depending on how much the appliance is used.
- Never wash the carbon filter in water unless the manufacturer states otherwise.
- Fat filters must always be installed even when the carbon filter is not installed. Do not use the appliance without the fat filter inserted.
Replacing the carbon filter
- For the correct operation of the appliance, it is necessary to install a carbon filter. The number and type depend on the model.
- Place the carbon filter on the motor outlets and turn it in the clockwise direction.
- To remove the carbon filter turn it in the anticlockwise direction.
PEB 608 IX
PEB 644 W
Ventilation
To ensure proper ventilation, leave windows closed while the appliance is
turned on.
WARNING!
Pay increased attention if you are using the appliance together with another
appliance that uses air or fuel for its operation (e.g. heating fan, fan,
etc.) or that uses gas, coal or wood, as its operation may negatively affect
the performance of the range hood because it expels air out of the room. This
warning does not apply if you installed the appliance without an exhaust out
of the room.
PART 4: OPERATION
PEB 608 IX
Remove the protective foil from the control panel.
Exhaust power selection
This range hood is equipped with 5 levels of exhaust power. Select the power
level based on the use of the stove and the amount of steam that the pots
emit.
To turn on the motor press the button and to set the exhaust power level
press the + or – button. Press the + button to increase the exhaust power and
the – button to reduce the exhaust power.
Automatic timer (TIMER)
All models with remote control are equipped with an automatic timer.
Press and hold the button at the set exhaust power level for at least 2
seconds and the automatic timer function will be turned on for a period of 15
minutes. When the function s turned on, the respective symbol will appear on
the display and the motor will turn off automatically after 15 minutes.
NOTE:
Use the range hood together with the stove. This will ensure the correct air
exhaust. We recommend leaving the range hood running a few minutes longer than
the stove to ensure that all odors are extracted.
Lighting
The range hood is equipped with lightning. Press the button with the light
symbol to turn on the lights. Press the button again to turn the lights off.
PEB 644 W, PEB 644 IX
Remove the protective foil from the control panel.
Exhaust power selection
This range hood is equipped with 3 levels of exhaust power. Select the power
level based on the use of the stove and the amount of steam that the pots
emit. Press the respective button on the control panel.
I – lowest exhaust power
II – medium exhaust power
III – highest exhaust power
Automatic timer (TIMER)
All models with electronic controls are equipped with an automatic timer.
Press and hold the respective button for the exhaust power level for at least
2 seconds and the automatic timer function will be turned on for a period of
15 minutes. When the function is turned on, the respective symbol will appear
on the display and the motor will turn ff automatically after 15 minutes.
NOTE:
Use the range hood together with the stove. This will ensure the correct air
exhaust. We recommend leaving the range hood running a few minutes longer than
the stove to ensure that all odors are extracted.
Lighting
The range hood is equipped with lightning. Press the button with the light
symbol to turn on the lights. Press the button again to turn the lights off.
Operating tips
- Regularly clean the aluminum filters and regularly replace the carbon and fat filters.
- Use the medium exhaust power level. Only use the highest power level when necessary.
- To ensure proper ventilation, leave windows closed while the appliance is turned on.
PART 5: MAINTENANCE AND CLEANING
WARNING!
Before cleaning, regular or other maintenance, installation or removal, check
that the appliance is turned off and disconnected from the power socket or
that the respective circuit breaker is turned off.
Changing a light bulb
PEB 608 IX
- To remove the halogen light bulb (50 W), press the light bulb holder downwards and gently turn it anticlockwise. Remove the light bulb.
- Install a light bulb with the same parameters in reverse sequence.
PEB 644 W, PEB 644 IX
- Turn off the appliance.
- Take out the aluminum filter.
- If the light bulb broke during operation wait until it cools down.
- Unscrew the broken light bulb. Install a new one with the same parameters.
Cleaning
- Aluminum filters capture dust and fat from the extracted air.
- It is necessary to regularly wash these filters, ideally once a month, depending on the level of use. Wash the filters in water with dishwashing detergent, or you may place the filters in a dishwasher and wash them using a gentle program (max. 60°C).
- Take out the aluminum filters by pressing the clip.
- After cleaning allow the aluminum filters to dry thoroughly before reinstalling them.
- Wipe the outer surface of the range hood with a clean damp wiping cloth lightly dipped in water with a small amount of dishwashing detergent. Then wipe dry.
- Avoid electrical parts coming into contact with water or another liquid.
- For cleaning, you can also use special agents for the maintenance and cleaning of INOX surfaces.
Cleaning the aluminum filters
The aluminum filters need to be cleaned when “C” appears on the display
(depending on the model). Clean the filters according to the above-mentioned
instructions and after installing them press and hold down the fan button for
3 seconds until the “C” symbol (depending on the model) disappears from the
display. The symbol “E” (depending on the model) will appear on the display,
which means that the appliance is ready for operation.
If you wish to use the appliance without clearing the “C” symbol (depending on
the model), press the fan button to start extraction for 1 second, then the
“C” symbol depending on the model) will appear again and the motor will
continue running.
NOTE:
The “C” symbol (depending on the model) appears on the display after
approximately 60 hours of operation.
WARNING!
For cleaning do not use petrol, benzene, thinners or any other solvents,
coarse cleaning agents, steel wool, or any sponges with steel wool.
WARNING!
You may put the aluminum filters in a dishwasher. The color of the aluminum
filters may change after several washes. This is a normal event.
PART 6: BEFORE YOU CALL THE SERVICE CENTRE
If the appliance is not working as it should check the following
recommendations for resolving the most common problems.
If the problem persists or it is not included in the table below, turn off the
appliance and disconnect it from the power socket and contact an authorized
service center.
| Problem | Solution |
|---|---|
| The range hood is not working. | Check that the power plug is properly inserted |
in a properly grounded power socket with the parameters 220 – 240 V – 50 Hz.
Check that the motor power switch is in the “On” position.
The lights are not working.| Check that the power plug is properly inserted in
a properly grounded power socket with the parameters 220 – 240 V – 50 Hz.
Check that the motor power switch is in the “On” position.
Check whether the light bulb or fluorescent tube is not broken.
Exhaust power is weak.| Check whether the aluminum filters are dirty.
Check the air outlet, it should be open.
Check whether the carbon filter is not too dirty.
The range hood does not extract the air directly out (for models without an
exhaust).| Check whether the aluminum filters are dirty.
Check whether the carbon filter is not too dirty.
ATTENTION:
Use the range hood together with the stove. This will ensure the correct air
exhaust. We recommend leaving the range hood running a few minutes longer than
the stove to ensure that all odors are extracted.
Directive EU 65/2014 – EN61591, EN60704-2-13, EN50554
Band| Philco
Model| PEB 608 IX/ EB 644 W/PE8 644 Ix
aooual fnengv Consumption| 43/79/99
Energy Efficiency Class| A+]D/E
fluid Dynamic Efficiency| 35,6/5,7/5.7
fluid Dwasic Efficiency class| 638 / 300/ 300
Light Efficiency| A/F/F
its deficiency Cars| 69/1/1
Grease Flt foxy| A/G/G
Gras Filtering efficiency Cats| 76,1/46,0/46,0
Minimum Air Flow in Normal| C/F/F
Morr A flew in Norm. a| 294 / 180 / 180
Ar lo at intensive| 638 / 300/ 300
Sound or Level at Mini run Speedable I Nome.al Le| –
Soun hoer Level at Mourn Speed Awai. bole in Normal| 55/47/47
Sound Power Level at intensive| 70/60/60
Power Consumption 0ff tee| –
hoer Corsugption in db Mode| 0,67/ 0,0 /0,0
Product information compliant with commission regulation FU) No| –
Tone increase facto
net file| 0,7/1,8/1,8
Measured air pressure at the best efficiency point| 390,0/134,0/ 134,0
Measured air pressure at the best efficiency point| 490 / 136 / 136
Measured electric power input at best efficiency point| 149,0/139,0/ 139,0
Norri. al power of the lighting system| 6,0/ 28,o /56,0
Average illumination of the lighting system on the cooling surface| 411/41/96
NOTE : All the here-mentioned data is subject to change.
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING
MATERIALS
Dispose of packaging material at a public waste disposal site.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES
The meaning of the symbol on the product, its accessory, or packaging
indicates that this product shall not be treated as household waste. Please,
dispose of this product at your applicable collection point for the recycling
of electrical & electronic equipment waste. Alternatively in some states of
the European Union or other European states, you may return your products to
your local retailer when buying an equivalent new product. The correct
disposal of this product will help save valuable natural resources and help in
preventing the potential negative impact on the environment and human health,
which could be caused as a result of improper liquidation of waste. Please ask
your local authorities or the nearest waste collection center for further
details. The improper disposal of this type of waste may fall subject to
national regulations for fi nes.
For business entities in the European Union
If you wish to dispose of an electrical or electronic device, request the
necessary information from your seller or supplier.
Disposal in other countries outside the European Union
If you wish to dispose of this product, request the necessary information
about the correct disposal method from local government departments or from
your seller.
****This product meets all the basic EU regulation requirements that relate
to it.
Changes to the text, design and technical specifications may occur without
prior notice and we reserve the right to make these changes.
is a registered trademark used under license from Electrolux International Company, U.S.A?
Documents / Resources
|
PHILCO PEB 608 IX Range
Hood
[pdf] User Manual
PEB 608 IX, PEB 644 W, PEB 644 IX, Range Hood, PEB 608 IX Range Hood
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>