Gude BS 18 Cordless Drill or Driver Instruction Manual
- June 5, 2024
- Gude
Table of Contents
BS 18 Cordless Drill or Driver
**Instruction Manual
**
BS 18 58500 / 58501 / 58502
BSB 18 58503 / 58504
GÜDE GmbH & Co. KG
Birkichstrasse 6
74549 Wolpertshausen Deutschland
Please read the instructions carefully before starting the machine.
STARTING-UP THE MACHINE
DELIVERY RANGE
Operation **
Starting up the machine**
Cordless Drill Driver| BS 18|
---|---|---
Cordless percussion drill/driver| | BSB 18
Art. No| 58500 / 58501/ 58502| 58503 / 58504
Battery voltage| 18 V | 18 V
No-load speed| 1st gear 2nd gear| 0 – 350 min-1
0 – 1250 min-1| 0 – 350 min-1
0 – 1250 min-1
Rate of percussion under load| 1st gear 2nd gear| –
–| 0-5250 min-1
0-18750 min-1
Torque max.| 30 Nm| 42 Nm
Drilling capacity max.| Steel plate Wood brick and tile| 10 mm
25 mm-| 12 mm
30 mm
8 mm
Screw diameter max. (Wood)| 6 mm| 8 mm
Drill chuck range| 0,8 – 10 mm| 2 – 13 mm
Weight without battery/Charging equipment| 1,0 kg| 1,3 kg
Noise details
Measured according to EN 60745; Uncertainty K = 3 dB (A)
Sound pressure level LpA| 84 dB(A)| 84 dB(A)
Sound power level LWA| 95 dB(A)| 95 dB(A)
Wear ear protectors!
Vibration details
Vibration total values (triaxial vector sum) determined according to EN
60745, Uncertainty K = 1,5 m/s2
Drilling into metal: Vibration emission value ah,D| 1,08 m/s²| 1,55 m/s²
Impact drilling into concrete: Vibration emission value ah,ID| –| 7,52 m/s²
Screw driving without impact: Vibration emission value ah| 0,59 m/s²| 0,59
m/s²
WARNING: The vibration emission level will vary because of the ways in
which a power tool can be used and may increase above the level given in this
information sheet. The vibration emission level may be used to compare one
tool with another. It may be used for a preliminary assessment of exposure. An
accurate estimate of the vibratory load should also take into account the
times when the tool is shut down or when it is running but not actually in
use. This may significantly reduce the vibratory load over the total working
period. Identify additional safety measures to protect the operator from the
effects of vibration such as: maintaining the tool and the accessories,
keeping the hands warm, and organization of work patterns.
Read and understand the operating instructions before using the appliance.
Familiarise yourself with the control elements and how to use the appliance
properly. Abide by all the safety measures stated in the service manual. Act
responsibly toward third parties.
The operator is responsible for accidents or risks to third parties. Persons
over 16 years of age can only work on the appliance. An exception includes
youngsters trained in order to reach knowledge under the supervision of the
trainer during occupational education. In case of any doubts about connection
and operation refer please to our customer center
Specified Conditions Of Use
BS 18: The battery drill/screwdriver may be used for drilling and the
screwdriver for independent use away from the mains supply.
BSB 18: The cordless percussion drill/driver is designed for drilling,
and percussion drilling, as well as a screwdriver for independent use away
from the mains supply. Do not use this product in any other way as stated for
normal use. Not observing general regulations in force and instructions from
this manual does not make the manufacturer liable for damages.
Emergency procedure
Conduct a first-aid procedure adequate to the injury and summon qualified medical attendance as quickly as possible. Protect the injured person from further harm and calm them down. If you seek help, state the following pieces of information: 1. Accident site, 2. Accident type, 3. A number of injured persons, 4. Injury type(s)
Symbols
WARNING / CAUTION!
WARNING – Read the operating instructions to reduce the risk of injury.
Wear eye protective goggles! Wear ear protectors!
Take the replaceable battery from the appliance before any extension,
cleaning, and servicing works.
CE marking
Any damaged or disposed of electric or electronic devices must be delivered to
appropriate collection centers.
Battery
Protect the battery against heat and fire.
Protect the battery against water and moisture.
Protect the battery against temperatures above 40°C.
Do not throw the batteries in household waste.
****Deliver the batteries to a collection center of old batteries where they
will be recycled in an environmentally friendly way.
WARNING Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or
serious injury. Save all warnings and instructions for future reference.
Screwdriver safety warnings
Hold power tool by insulated gripping surfaces, when performing an operation
where the fastener may contact hidden wiring. Fasteners contacting a,,live”
wire may make exposed metal parts of the power tool,, live” and could give the
operator an electric shock.
Drill safety warnings
Wear ear protectors when impact drilling. Exposure to noise can cause hearing
loss. Use auxiliary handle(s), if supplied with the tool. Loss of control can
cause personal injury. Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may contact hidden wiring.
Cutting accessory contacting a,,live” wire may make exposed metal parts of the
power tool,,live” and could give the operator an electric shock.
Additional Safety and Working Instructions
Use protective equipment. Always wear safety glasses when working with the
machine. The use of protective clothing is recommended, such as a dust mask,
protective gloves, sturdy non-slip footwear, and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Use a dust absorption system and wear a suitable dust protection
mask. Remove deposited dust thoroughly, e.g. with a vacuum cleaner.
Do not machine any materials that present a danger to health (e.g. asbestos).
When working on walls ceilings, or floors, take care to avoid electric cables
and gas or water pipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause
severe injury and damage. Please turn the device immediately off when the tool
used gets blocked! Do not turn the device on again when the tool is still
blocked. This could cause a bounce back with a high reaction moment. Determine
and remove the cause of the blocking of the tool used while respecting the
safety instructions. The possible causes may be:
- it is tilted in the workpiece to be machined
- it has pierced through the material to be machined
- the power tool is overloaded
Do not reach into the machine while it is running. Chips and splinters must
not be removed while the machine is running.
WARNING! The danger of burns The insertion tool may become hot during
use.
- when changing tools
- when setting the device down
The appliance must not be used if damaged or if safety equipment is defective.
Replace any worn-out and damaged parts. Do not use the device near flammable
liquids or gases. Risk of fire and explosion in case of short circuit. Do not
let any metal parts reach the airing slots danger of short circuits!
Battery
Risk of fire! Risk of explosion!
Never use damaged, defective or deformed accumulators. Never open or damage
the accumulator or let it fall on the ground.
Umgebungstemperatur
Protect the battery against heat and fire.
Battery to be used at ambient temperatures between 10°C and +40°C only.
Never put the battery on heaters and do not expose it to strong sunlight for a
long time.
After being subject to heavy load, let the battery cool down first. Short
circuit – do not bridge the accumulator contacts with metal parts.
The accumulator must be packaged (plastic bag, box) or accumulator contacts
must be sealed up for accumulator disposal, transport or storage.
The Güde charger to be used only to charge the battery.
There can be a malfunction or fire if different chargers are used.
Vapors may leak out in case of unauthorized use or when using a damaged
accumulator. Bring fresh air and seek medical advice if experiencing
difficulties.
Vapors may irritate the respiratory system.
Work instructions
Accumulators are supplied partially charged and must therefore be fully
charged before being used for the first time.
- Charge the accumulator when the appliance is running slowly or stops.
- A li-ion battery may be charged at any time without any shortening of its life. Charging process interruption will not damage the accumulator.
- A li-ion battery is protected by the Electronic Cell Protection against deep discharge.
- A significantly shorter operating time of a charged battery means the battery life is over and the battery must be replaced.
Dispose of the batteries in an environmentally friendly manner.
Li-ion batteries are subject to the special disposal obligation. Have any
defective batteries been disposed of by a specialized shop? The battery must
be taken out before the appliance is scrapped. Damaged batteries may harm the
environment and your health if toxic vapors or liquids leak out of such
batteries. Therefore, never send a defective battery by post, etc. Please
contact your local recycling center. Dispose of the batteries when discharged.
We recommend applying adhesive tape on the poles to protect them against short
circuits. Never open the battery.
Maintenance
**** Take the replaceable battery from the appliance before any extension,
cleaning, and servicing works.
Repairs and works specified in these Instructions may only be performed by
qualified authorized staff.
Use only original accessories and original spare parts. Keep the device, in
particular the air vents, clean at all times. Never spray water on the
device’s body! Do not clean the plastics with solvents, flammable or toxic
fluids. For cleaning, use a damp cloth only. Only a regularly maintained and
treated appliance can serve as a satisfactory aid. Insufficient maintenance
and care can lead to unforeseen accidents and injuries.
If necessary, a list of spare parts can be found at
www.guede.com.
Translation of the EC-Declaration of Conformity
We, hereby declare the conception and construction of the below-mentioned
appliances correspond – at the type of construction being launched – to the
appropriate basic safety and hygienic requirements of EC Directives. In case
of any change to the appliance not discussed with us, the Declaration expires.
Akku-Bohrschrauber
58500 — BS 18
Method of compliance assessment
Wolpertshausen, 27/10/2016
Managing Director
Joachim Bürkle
GÜDE GmbH & Co. KG, Birkichstraße 6, 74549 Wolpertshausen, Germany
EN 60745-1:2009+A11:2010
EN 60745-2-1:2010
EN 60745-2-2:2010
AfPS GS 2014:01 PAK
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
Measured sound power leve
Authorized to compile the technical file
Cordless percussion drill/driver
Method of compliance assessment
Wolpertshausen, 27/10/2016
Managing Director
Joachim Bürkle
GÜDE GmbH & Co. KG, Birkichstraße 6, 74549 Wolpertshausen, Germany
GÜDE GmbH & Co. KG
Birkichstrasse 6
74549 Wolpertshausen
Deutschland
Tel.: +49-(0)7904/700-0
Fax.: +49-(0)7904/700-250
eMail: info@guede.com
TN 58500, 58501, 58502, 58503, 58504 2017-02
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>