AXXESS XSVI-6523-NAV Wiring Interface Adapter Instruction Manual

: June 5, 2024
: AXXESS

Table of Contents

INTERFACE FEATURES
APPLICATIONS
Connections to be made
Initializing the XSVI-6523-NAV
Initializing the XSVI-6523-NAV
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Installation instructions for part XSVI-6523-NAV
XSVI-6523-NAV
Chrysler Data Interface 2013-up

INTERFACE FEATURES

Provides accessory power (12-volt 10-amp)
Retains R.A.P. (retained accessory power)
Can be used in both amplified and non-amplified models
Provides NAV outputs (parking brake, reverse, and speed sense)
Pre-wired ASWC-1 harness (ASWC-1 sold separately)
Retains the factory backup camera (if displayed through the OE radio)
Retains the 3.5mm AUX-IN jack
Retains balance and fade
Micro “B” USB updatable

APPLICATIONS

CHRYSLER

INTERFACE COMPONENTS

XSVI-6523-NAV interface
XSVI-6523-NAV harness

TOOLS REQUIRED

Wire cutter
Crimp tool
Solder gun
T ape
Connectors (example: butt-connectors, bell caps, etc.)

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

Connections to be made

From the XSVI-6523-NAV harness to the aftermarket radio:

Connect the Black wire to the ground wire.
Connect the Yellow wire to the battery wire.
Connect the Red wire to the accessory wire.
Note: If installing an ASWC-1 (sold separately), there will be an accessory wire there to connect as well.
For the Fiat 500L only: Connect the Blue/White wire labeled “500L amp turn on” to the amp turn on wire. This wire must be connected to hear sound from the factory amplifier.
For all models except the Fiat 500L: Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear sound from the factory amplifier.
If the aftermarket radio has an illumination wire, connect the Orange wire to it.
Connect the Gray wire to the right front positive speaker output.
Connect the Gray/Black wire to the right front negative speaker output.
Connect the White wire to the left front positive speaker output.
Connect the White/Black wire to the left front negative speaker output.
Connect the Green wire to the left rear positive speaker output.
Connect the Green/Black wire to the left rear negative speaker output.
Connect the Purple wire to the right rear positive speaker output.
Connect the Purple/Black wire to the right rear negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these wires.

Connect the Blue/Pink wire to the VSS/speed sense wire.
Connect the Green/Purple wire to the reverse wire.
Connect the Light Green wire to the parking brake wire.
If retaining the factory backup camera, connect the Yellow RCA jack to the backup camera input.
If retaining the factory AUX-IN jack, connect the Red & White RCA jacks to the AUX input.

12-pin pre-wired ASWC-1 harness:

This harness is to be used along with the optional ASWC-1 (not included) to retain steering wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If it will be used, please refer to the ASWC-1 instructions for radio connections and programming.
Note: Disregard the harness that comes with the ASWC-1.
Connect the Red wire to the accessory wire.

Initializing the XSVI-6523-NAV

With the key in the off position:

Connect the XSVI-6523-NAV harness into the interface, and then to the harness in the vehicle.
Note: For the Fiat 500L and Ram Promaster City, do not connect the harness to the vehicle yet.
Note: If using the ASWC-1, connect it after you initialize and test the XSVI-6523-NAV, with the key in the off position.

Initializing the XSVI-6523-NAV

Attention! If the interface loses power for any reason, the following steps will need to be performed again. Also, if installing an ASWC-1 connect it after you initialize and test the interface/radio, with the key in the off position.

For the Fiat 500L and Ram Promaster City:

Turn the hazard lights on.
Connect the XSVI-6523-NAV harness to the wiring harness in the vehicle.
Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on.
Note: If the radio does not come on within 60 seconds, turn the key to the off position, disconnect the interface, check all connections, reconnect the interface, and then try again.
Turn the key to the off position, and then to the accessory position. Turn off the hazard lights. Test all functions of the installation for proper operation, before reassembling the dash.

For all other models:

Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on.
Note: If the radio does not come on within 60 seconds, turn the key to the off position, disconnect the interface, check all connections, reconnect the interface, and then try again.
Turn the key to the off position, and then to the accessory position. Test all functions of the installation for proper operation, before reassembling the dash.

IMPORTANT
If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certiﬁed technicians

REV. 7/7/2016 INSTXSVI-6523-NAV
Metra recommends MECP certified technicians
Axxess Integrate axxessinterfaces.com · metraonline.com
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION

http://axxessinterfaces.com/