AXXESS AXTO-MI2 Mitsubishi Amplifier Interface Installation Guide
- June 1, 2024
- AXXESS
Table of Contents
AXXESS AXTO-MI2 Mitsubishi Amplifier Interface
Specifications
- Product Name: AXTO-MI2 Mitsubishi Amplifier Interface
- Compatibility: Mitsubishi vehicles – Lancer 2008-2013, Outlander Sport 2011-2013, Outlander 2007-2013
- Model: AXTO-MI2
- Revision Date: 1/21/2020
Product Usage Instructions
Installation
- Before starting the installation process, ensure to disconnect the negative battery terminal as a safety precaution.
- Make all necessary connections as per the provided instructions, ensuring that all accessories and switches are plugged in before reconnecting the battery or cycling the ignition.
Connections
- If the radio lacks RCA outputs or only has one pair, utilize the Axxess AXLOC4-80A (4 Ch.) or AXLOC-80A (2 Ch.) line-level converters (sold separately).
Initializing and Adjusting
- Use the AXTO-MI2 for mid/high speaker control and subwoofer control. Refer to Figure A for visual guidance.
FAQ
Q: What should I do if unsure about the installation process?
A: If you are unclear about the instructions or lack the understanding to complete the installation safely, it is recommended to consult a technician with the necessary knowledge. For further assistance, contact Metra at 1-800-2210932.
Q: Where can I enhance my installation skills?
A: Consider enrolling in the Installer Institute to improve your installation and fabrication skills. Visit www.installerinstitute.com or call 800-354-6782 for more information.
APPLICATIONS
MITSUBISHI
- Lancer 2008-2013
- Outlander Sport 2011-2013
- Outlander 2007-2013
FEATURES
- Retains the factory amplifier
- Provides multimedia wires (parking brake, reverse, and speed sense)
- RCA level input
- Retains balance and fade
INTERFACE COMPONENTS
- AXTO-MI2 interface
- AXTO-MI2 harness
- 14-pin harness with stripped leads and RCA jacks
TOOLS REQUIRED
- Cutting tool
- Crimping tool
- Tape
- Small flat-blade screwdriver
- Connectors (example: butt-connectors, bell caps, etc.
- CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation.
- All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.
- NOTE: Refer to the instructions included with the aftermarket radio.
Connections to be made
From the 14-pin harness to the aftermarket radio:
- Connect the Red wire to the accessory wire.
- Connect the Blue/White wire to the amp and turn on the wire (this wire must be connected to hear sound from the factory amplifier).
- Tape off and disregard the Brown wire, it will not be used in this application.
- Connect the White RCA to the left front output.
- Connect the Gray RCA to the right front output.
- Connect the Green RCA to the left rear output.
- Connect the Purple RCA to the right rear output.
- Note: If the radio does not have RCA outputs or only one pair, use the Axxess AXLOC4-80A (4 Ch.) or AXLOC-80A (2 Ch.) line-level converters (sold separately).
- The following wires are for aftermarket multimedia/navigation radios that provide these wires (if not required, tape them off and disregard them):
- Connect the Light Green wire to the parking brake wire.
- Connect the Blue/Pink wire to the speed sense/ V.S.S. wire.
- Connect the Green/Purple wire to the reverse wire.
- Note: Reverse wire is not available on manual transmission vehicles.
- Plug the 14-pin harness into the AXTO-MI2
From the AXTO-MI2 harness:
- Connect the Black wire to the ground wire.
- Connect the Yellow wire to the battery wire.
- Connect the Blue wire to the power antenna turn-on wire.
- Connect the Orange wire to the Illumination wire. (If the aftermarket radio has no Illumination wire, tape off the Orange wire.)
- Connect the 16-pin harness to the AXTO-MI2.
- Connect the 18-pin and 20-pin harness to the vehicle.
Initializing and adjusting the AXTO-MI2
- Initialize the interface by turning the ignition on for 30 seconds, then turn the ignition back off, and on again.
- If the speakers are too loud, or not loud enough, you can adjust the output by following the steps below:
- Locate the end of the AXTO-MI2 with the 14-pin harness with stripped leads and RCA jacks.
- Using a small flat-blade screwdriver, turn the gain knob clockwise to make it louder, or counterclockwise to make it lower.
IMPORTANT WARNING
- This product includes instructions for installation which must be carefully followed.
- The instructions are worded in such a manner as to assume that the installer is capable of completing these types of electronic installations.
- If you are unclear as to what you are instructed to do or believe that you do not understand the instructions to properly and safely complete the installation you should consult a technician who does have this knowledge and understanding.
- Failure to follow these instructions carefully and to install the interface as described could cause harm to the vehicle or safety systems on the vehicle.
- Interference with certain safety systems could cause harm to persons as well. If you have any questions in this regard please call the Helpline or Metra at 1-800-221- 0932 for assistance.
KNOWLEDGE IS POWER
- Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
- Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
- Metra recommends MECP-certified technicians
- METRA. The World’s best kits.™ 1-800-221-0932 metraonline.com
- © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>