Laserliner 032 060 PowerCross-Laser 5G Cross Line Laser Instruction Manual

Laserliner 032 060 PowerCross-Laser 5G Cross Line Laser

Completely read through the operating instructions, the „Warranty and Additional Information“ booklet as well as the latest information under the internet link at the end of these instructions. Follow the instructions they contain. This document must be kept in a safe place and if the laser device is passed on, this document must be passed on with it.

Function / Application

• Cross-line laser with intense light green laser lines for horizontal and vertical leveling with plum function.
• The vertical lines are aligned at right angles to one another.
• The slope-mode feature is an extra that permits gradients to be laid out.
• A simple, precise plumb function is afforded by the additional plumb laser at the bottom and the laser cross at the top.
• Individually switchable laser lines.
• Out-Of-Level: is indicated by optical signals when the unit is outside its self-leveling range.
• Long-lasting, powerful lithium-ion rechargeable battery.
• The pivoted housing can be turned with a vernier adjustment mechanism to permit the exact positioning of laser lines.
• Automatic leveling range 2°, accuracy 0.15 mm / m.

General safety instructions

• The device must only be used in accordance with its intended purpose and within the scope of the specifications.
• The measuring tools and accessories are not toys.
• Keep out of reach of children.
• Modifications or changes to the device are not permitted, this will otherwise invalidate the approval and safety specifications.
• Do not expose the device to mechanical stress, extreme temperatures, moisture, or significant vibration.
• The device must no longer be used if one or more of its functions fail] or the battery charge is weak.
• Use the power supply/charger unit only in closed rooms; do not expose to moisture or rain otherwise risk of electric shock.

Safety instructions

Using class 2 lasers

• Laser radiation!
• Do not stare into the beam!
• Class 2 laser < 1 mW · 515 / 650 nm
• EN 60825-1:2014

Attention: Do not look into the direct or reflected beam.

• Do not point the laser beam towards persons.
• If a person‘s eyes are exposed to class 2 laser radiation, they should shut their eyes and immediately move away from the beam.
• Under no circumstances should optical instruments (magnifying glass, microscope, binoculars) be used to look at the laser beam or reflections.
• Do not use the laser at eye level (1.40…1.90 m)
• Reflective, specular, or shiny surfaces must be covered whilst laser devices are in operation.
• In public areas shield off the laser beam with barriers and partitions wherever possible and identify the laser area with warning signs.

Safety instructions

• Dealing with electromagnetic radiation
• The measuring device complies with electromagnetic compatibility regulations and limits in accordance with the EMC Directive 2014/30/EU.
• Local operating restrictions – for example, in hospitals, aircraft, petrol stations, or in the vicinity of people with pacemakers – may apply.
• Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.

Information on maintenance and care

• Clean all components with a damp cloth and do not use cleaning agents, scouring agents, or solvents. Remove the batteries) before storing for longer periods. Store the device in a clean and dry place.

Special product features

Number and direction of the lasers

• H = horizontal laser
• V = vertical laser
• D = down point

OVERVIEW

1. Laser emitting window
2. ON / OFF switch transport fastener
3. 360° horizontal circle
4. Vernier adjustment
5. 5/8“ thread (underside)
6. The window for the plumb laser (underside)
7. Adjustable feet with removable rubber caps
8. Adapter for crank tripods and telescopic stands
9. Vial for approximate alignment with backlight / low bat. display: low battery charge when bubbling level flashes
10. Lithium-ion rechargeable battery (detachable)
11. Vertical laser line
12. Horizontal laser lines
13. Connection socket for the battery charger

• For transport, the device must always be switched off with the transport securing device (2) so as to protect the device from damage.

Use of lithium-ion rechargeable battery

Before using the laser for the first time, insert the battery into the device and fully charge (at least 4 hours).  Connect the battery charger to charge the battery. The LED of the battery pack lights red while the battery is charging. When the LED changes to green, charging is complete. When the backlight of the circular levelflashes, the battery is low. In that case, recharge the battery. The rechargeable battery can either be charged when it is not inserted into the device or when the device is in use.

• The battery may only be charged with the battery charger provided and used only in this laser device. Any other use may cause injury or fire.
• Make sure there are no conductive objects in the vicinity of the battery contacts. Short-circuiting of these contacts can cause burn injuries or fire.
• Do not open the rechargeable battery. This could cause short circuits.

Horizontal and vertical leveling

• Turn the transport fastener (2) clockwise and release the pendulum lock.
• The lasers are now automatically aligned by the pendulum system and the horizontal laser lights constantly.
• The lasers can be switched on and off individually with the H and V buttons. It is now ready for leveling in the horizontal or vertical plane.

If the device is too far off the horizontal (more than 2°), the lasers will blink. Align the device using the adjustable feet (7) or place on a more level surface. The round vial (9) is provided as an aid to alignment.

Slope mode

Do not release the pendulum lock or turn the transport fastener (2) counterclockwise. Switch on the lasers (buttons 11, and 12). Sloping planes and tilts can now be measured. The lasers flash once in a while to show that the device is not aligning automatically.

Positioning laser lines

• The top section of the laser unit can be turned on the plinth to align the lasers approximately. Precise positioning can then be done with the Vernier adjustment (4).
• The adjustable feet (7) allow the device to be positioned on sloping surfaces.
• The freely rotatable horizontal circle (3) makes it easy to turn the deviceto the required angle. Simply set the scale to zero, then rotate the device to the angle you want.

Hand receiver mode

Optional: Working with the laser receiver GRX

• Use a GRX laser receiver (optional) to carry out leveling at great distances or when the laser lines are no longer visible.
• Manual receiver mode is switched on automatically.

Follow the operating instructions of the corresponding laser receiver.

EU directives and disposal

This device complies with all necessary standards for the free movement of goods within the EU. This product is an electric device and must be collected separately for disposal according to the European Directive on waste electrical and electronic equipment. Further safety and supplementary notices at: http://laserliner.com/info?an=pocrolas5g

Preparing the calibration check

It is possible for you to check the calibration of the laser. To do this, position the device midway between 2 walls, which must be at least 5 meters apart. Do this by turning the unit on, thus releasing the transport restraint (cross laser on). Please use a tripod.

1. Mark point A1 on the wall.
2. Turn the device through 180° and mark point A2. You now have a horizontal reference between points A1 and A2.

Performing the calibration check

1. Position the device as near as possible to the wall at the height of point A1.
2. Turn the device through 180° and mark point A3. The difference between points A2 and A3 is the tolerance.

When A2 and A3 are more than 0.15 mm / m apart, an adjustment is necessary. Contact your authorized dealer or else the UMAREXLASERLINER Service Department.

Checking the vertical line

Position the device about 5 m from a wall. Fix a plumb bob with a line of 2.5 m length on the wall, making sure that the bob can swing freely. Switch on the device and align the vertical laser to the plumb line. The precision is within the specified tolerance if the deviation between the laser line and the plumb line is not greater than ± 0.75 mm.

Checking the horizontal line

Position the device about 5 m from a wall and switch on the cross laser. Mark point B on the wall. Turn the laser cross approx. 2.5 m to the right and mark point C. Check whether the horizontal line from point C is level with point B to within ± 0.75 mm. Repeat the process by turning the laser to the left.

• Regularly check the adjustment before use, after transport, and after extended periods of storage.

Technical data (Subject to technical alterations. 18W21)

Self-levelling range| ± 2°
Precision| ± 0.15 mm / m
Laser wavelength linelaser (green)| 515 nm
Laser wavelength plumb laser (red)| 650 nm
Laser class| 2 / ≤ 1 mW
Power supply| Lithium-ion rechargeable battery
Battery operating time (all lasers on)| approx. 4 h
Battery recharging time| approx. 4 h

Operating conditions

| 0…50°C, max. humidity 80% RH, no condensation, max. working altitude 4000 m above sea level
Storage conditions| -10…70°C, max. humidity 80% rH
Weight (incl. rechargeable battery)| 1.4 kg
Dimensions (W x H x D)| 120 x 120 x 200 mm

SERVICE

Umarex GmbH & Co. KG

• Laserliner
• Möhnestraße 149, 59755 Arnsberg, Germany
• Tel: +49 2932 638-300, Fax: +49 2932 638-333
• info@laserliner.com

Umarex GmbH & Co. KG

• Donnerfeld 2
• 59757 Arnsberg, Germany
• Tel: +49 2932 638-300, Fax: -333
• www.laserliner.com

References

• Info - Laserliner
• Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>